Panasonic WV-BP550 User Manual

CCTV CamerasWV-BP550/WV-BP554(Lens : option)Before attempting to connect or operate this product,please read these instructions completely.FRANÇAISEN

2. 24 V AC Power SupplyConnect the power cable to the AC/DC compatibleinput terminal on the rear panel of the camera.Copper wire #24 #22 #20 #18size (

-9-Type of RG-59/U RG-6U RG-11/U RG-15/Ucoaxial cable (3C-2V) (5C-2V) (7C-2V) (10C-2V)Recommended (m) 250 500 600 800maximumcable length (ft) 825 1,65

-10-Installation of Auto Iris Lens ConnectorInstall the lens connector (YFE4191J100) when using avideo drive ALC lens.The installation should be made

Caution for Mounting the LensThe lens mount should be a C-mount or CS-mount (1”-32UN) and the lens weight should be less than 450g(0.99 lbs). If the l

The following adjustment should be made by qualifiedservice personnel or system installers.1. Loosen the screws on the flange-back adjustingring.2. Tu

• Mounting from the bottomThis camera is designed to be mounted from thebottom, as shown below. The mounting hole is astandard photographic pan-head s

-14-1. CAMERA SETUP MENUThis camera utilizes a user setup menu that is displayed on-screen.The setup menu contains various items that form a tree-type

-15-MotionDetectorON/OFFLens DriveSignalSelectionDC VideoSpecialmenuDetectionLevelAdjustmentDetectionMasking AreaSelectionUpsidedownAPGainPede

-16-Left ButtonSet SwitchRight ButtonDown ButtonUp ButtonUp Button (): This button is used to move thecursor upwards. Use this button toselect an item

** CAM SET UP **CAMERA ID OFF ALC/ELC ALC SHUTTER ---AGC ONSENS UP OFFSYNC INTMOTION DET OFF LENS DRI

WARNING:TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.The lightning flash with arrowheadsymbol, within an

-18-• Editing the SPECIAL menuTo edit the SPECIAL menu (change settings), proceedas for editing the CAM SET UP menu above.Move the cursor to END after

-19-1. Camera Identification (CAMERA ID)SettingYou can use the camera identification (CAMERA ID) toassign a name to the camera. The camera ID consists

-20-2. Move the pointer to the character to be edited bypressing or . Then move the cursor to thecharacter area and select a new character.3. Press

-21-2-1. ALC Mode with SUPER-D ONSuper Dynamic Function (SUPER-D)The important object in a scene is usually placed in thecenter of the monitor’s scree

-22-2. Move the cursor to MASK SET and press . The48 mask areas appear on the monitor screen. Thecursor is blinking in the top left corner of thescre

-23-4. Repeat step 1 to 3 to mask the desired area.Tocancel masking, move the cursor to that area andpress .5. After masking is completed, press for

-24-4. Gain Control Setting (AGC ON/OFF)You can set the gain (brightness level portion of animage) to automatic level adjustment (ON) or fixedlevel(OF

-25-• When ON is selected for SUPER-D, the SENS UPSELECT function for the WV-CU254 or WV-CU300system controller does not work.Use the buttons on the s

-26-5. The VS gen-lock mode has its own menu for hori-zontal phase adjustments. When the cable lengthof the video output or the gen-lock input ischang

-27-7. Set the oscilloscope to the horizontal rate andexpand the horizontal sync portion on the oscillo-scope.8. Adjust the horizontal phase by pressi

CONTENTSPREFACE ...

-28-(FINE adjustment can be made up to 22.5 degreesby pressing or .)Notes:• When the “I” cursor reaches the “+” end, itjumps back to “−”. At the sam

-29-1. Move the cursor to the LENS DRIVE parameter.2. Select DC if you are using the auto iris lens thatrequires a DC drive signal.Select VIDEO if you

-30-9. Special Menu (SPECIAL)This menu lets you adjust and set up the video signalof the camera to meet your requirements.Move the cursor to END on th

-31-When the camera is aimed at a bright light, such as aspotlight, or a surface that reflects bright light, smearor blooming may appear. Therefore,

Pick-up Device: 771 (H) x 492 (V) pixels, Interline Transfer CCDScanning Area: 4.8 (H) x 3.6 (V) mm (Equivalent to scanning area of 1/3” pick-up tube)

-33-Power Source and WV-BP550: 120V AC 60 Hz, 5.3WPower Consumption: WV-BP554: 24V AC 60 Hz, 5.4W12V DC, 570 mADimensions (without lens): 67 (W) x 55

Video Imaging Systems CompanyA Division of Panasonic Broadcast & Television Systems CompanyA Unit of Matsushita Electric Corporation of AmericaExe

1. The following functions are built in.(1) Auto Light Control (ALC)/Electronic LightControl (ELC)(2) The SUPER-D function eliminates interferenceby s

1. Do not attempt to disassemble the camera.To prevent electric shock, do not remove screwsor covers.There are no user serviceable parts inside. Ask a

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS-4-SUPERDYNAMICWV-BP550SUPERDYNAMICWV-BP550Hi-Z G/L 75ΩVIDEO OUTPOWER120V AC 60HzGEN-LOCKALARM OUTGNDVID

q Auto Iris Lens ConnectorThis connector is used to connect with the auto irislens by a 4-pin male connector that is supplied asa standard accessory (

!3 Video Output Connector (VIDEO OUT)This connector is used to connect with the VIDEOIN connector of the monitor.!4 Power Cord SocketThis socket is us

Copper wire #24 #22 #20 #18size (AWG) (0.22mm2) (0.33mm2) (0.52mm2) (0.83mm2)Resistance 0.078 0.050 0.030 0.018Ω/mResistance 0.026 0.017 0.010 0.006Ω/