Before attempting to connect or operate this product,please read these instructions carefully and save this manual for future use.The model number is
10Major Operating Controls and Their FunctionsALARMALARMSUSPENDOPERATEERROR TIMER REC 1-LINK/ACT-2HDD1 HDD2 HDD3 HDD4ESC SETPULLNetwork Disk RecorderW
11!2 Escape Button (ESC)Use this button to display the previously displayed itemon the LCD.!3 Set Button (SET)Use this button to determine the edited
12Rack MountingImportant:• When installing the unit in the rack without turning the power of the unit off, activate the HDD safety mode. (Refer to pag
13ConnectionsThe following are descriptions of how to connect the unit with PCs, cameras and an optional extension unit.Required devices and cables va
14Connection between cameras and PCsWhen connecting the unit and PCs through a hub, use a LAN cable (straight) to connect between the unit and a hub.C
15<Connecting multiple units>10/100BASE-T21EXT STORAGESERIALPCCAMERAAC INALARM/CONTROLALARMSIGNAL GNDPOWERONOFF10/100BASE-T21EXT STORAGESERIAL
16Connecting with Extension UnitUp to 6 extension units can be connected with a single network disk recorder.Use the dedicated cable to connect betwee
17When connecting two extension units or more, connect them as follows. Up to 6 extension units can be connected to a singleunit. When connecting the
18 How to Use the Terminals of the ALARM/CONTROL ConnectorThese terminals are used for emergency recording, auto time adjustment, taking measures aga
19● Connection for emergency recordingWhen the external switch is turned ON, emergency recording will be started.Recording time and recording rate for
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CARE-FULLY.This appliance is supplied with a moulded three pin mains plug for yoursafety and convenienc
20• When "Auto Adjust Time" of "Time & Date" of "System" on the SETUP MENU is set to "SLAVE""Time Adj
21● Connection with the Uninterruptible Power System (UPS)This is an example of connection with the uninterruptible power system (UPS) to be installed
22 How to Use the Terminals of the ALARM ConnectorThese terminals are used to connect the alarm devices, such as sensors, door switches, etc.The pin
23Terminal● Alarm connectionWhen a signal is supplied to the alarm input terminals recording and displaying of camera images will be performed accordi
24How to Replace Hard Disk DrivesReplacement of hard disk drives is available regardless ofwhether the power of the unit is on or off.The procedure of
25• Remove the screws (4 for each drive unit) and pull thedrive units out.• Avoid missing the screws for reattaching.* For replacement of hard disk dr
26When replacing the hard disk drive with theunit power onz Call up the "HDD Setup" display on the LCD, and pressthe [SET] button.The follow
27Turn off the Power of the UnitTo shutdown the unit, do the following. 1. When the manual recording is being performed,stop the recording.Click the
28Operation Using the Buttons on the Front PanelThe following are the available functions using the buttons on the front panel and the LCD.The display
29DHCPIP addressSubnet maskGatewayHTTP portOFF192.168.0.250255.255.255.0192.168.1.1–OFF192.168.1.250255.255.255.080–192.168.2.250255.255.255.0––Camera
3Limitation of LiabilityTHIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WAR-RANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,INCLUDING BUT NOT LIMI
30Set the Network SettingsIt is possible to set the network settings. The available settings items are the same as described in the "Check the Ne
31Key Lock SettingsIt is possible to lock the buttons on the front panel to make them unusable. When the [SET] button is pressed while displaying the
32Shift the display on the LCD using the arrows button (C and D).C Arrows buttons DC Arrows buttons D[SET][ESC]C Arrows buttons DC Arrows buttons DC A
33Set the HDD Safety ModeWhen installing/uninstalling the unit in the rack without turning the power of the unit off, do the following. (Steps 1, 2.)W
34Check the Unit Number of the Extension UnitThe unit number of the connected extension unit can be checked with the HDD access indicators on the exte
35Reboot the Unit ManuallyIt is possible to reboot the unit manually as follow.Press the [SET] button while displaying the [REBOOT] display.The messag
36• The fan is not functioning because of the malfunction.Refer to the dealer.TroubleshootingCheck the following before requesting repair Contact a de
37Inspect the power cord, power plug and connectors periodically. • The power cord, plug and connectors are worn out. This may result in electricshock
38Standard AccessoriesCD-ROM* ... 1 pc.Inst
3939[English]Declaration of Conformity with the requirements of Technical Regulation on the Restriction Of the use of certainHazardous Substances in E
4Important Safety Instructions1) Read these instructions.2) Keep these instructions.3) Heed all warnings.4) Follow all instructions.5) Do not use this
Disposal may be regulated in your community due to environmental considerations. For disposal or recycling information,please visit Panasonic website:
5CONTENTSLimitation of Liability ...
6Precautions• Refer all work related to the installation of this prod-uct to qualified service personnel or systeminstallers. • Do not operate the uni
7• Indication labelRefer to the indication label placed on the surface ofthe unit as to the indications of equipment classificationand power source, e
8• Adobe, Adobe logos, and Acrobat are registered trademarks of Adobe Systems Incorporated in the U.S. and/or othercountries. • Microsoft, Windows and
9PrefaceThe Network Disk Recorders WJ-ND300A is designed for use within a surveillance system.The network disk recorder is a recording device using a
Comments to this Manuals