Panasonic WR-XS3P User Manual

Before attempting to connect or operate this product,please read these instructions carefully and save this manual for future use.Model No. WR-XS3Audi

10Input level: –10 dBVImpedance: 10 kΩo Multiple mono input connector [MULTI INPUT MONO]Connects a microphone. When using this connector,remove the sh

11System ConfigurationDecide what kind of system to form. Determine the num-ber of the external devices, the connection form, and themode (p. 14 Unit

12Secure the unit by 4 pieces of rackmounting screws (M5 x 12) in theaccessories.Where to install How to install1. Install the unit on a rack.Apply th

13 Cable InformationThe usable cable types, plugs, and connectors are the following.Before connection, sure you are using the proper cables.Screw (x3

14After connecting the external devices, do the following procedures:• Mode setting• Input signal assignment to the SUB OUTPUT jack• Output signal ass

15Mono amplificationThe signals from stereo or mono inputs are mixed and output through the MONO OUTPUT jack toward one zone.Signal FlowTo adjust the

16● Mode 2The stereo input signals are output through the STEREO OUTPUT jack, and mono input signals are output through MONOOUTPUT jack.BGM is output

17● Mode 3The signals from stereo or mono input lines are separately output through the STEREO OUTPUT, MONO OUTPUT and SUBOUTPUT jack. For example, th

18 Input Line Setting for SUB OUTPUT The SUB OUTPUT jack at the rear panel can output any signal from the STEREO INPUT 1 to 4 jacks or MONO INPUT 1 t

19 Output Line Setting for MULTI IN/LINE INThe signal from the MULTI IN ST jacks and MULTI IN MONO connector at the rear panel can be output through

2The serial number of this product may be found on the bot-tom of the unit.You should note the serial number of this unit in the spaceprovided and ret

20When using the MULTI INPUT ST jacks (or MONO connector) and LINE IN jack at the same timeIn this case, the signal from the MULTI INPUT ST jacks will

21 Example 1: Home Party (Mode 1)•Set the DIP switches to Mode 1. (Refer to p. 15.).• Mic 1 to 4 (MONO IN 1 to 4), Key (ST IN 1), Bass AMP (ST IN 2)

22 Example 2: Presentation Room (Mode 2)MONO IN 1REC OUTMONO IN 2MONO IN3 to 4ST IN1 to 4LINE INSUB OUTMONO OUTST OUT LST OUT RONOFF42810016428100264

23 Example 3: Shop (Mode 3)ST OUT LMONO IN 1MONO IN 2MONO IN 3MONO IN 4MULTI IN STMONO OUTSUB OUTST IN 1 to 4ONOFF42810016428100264281003642810046MON

24When you connect a cassette tape recorder or MD recorder to record the broadcasting, confirm the following: Notice about Recorder ConnectionsHowlin

25 Recording and Playback with One DeckTo record and play back a broadcast with one deck, connect the SUB OUTPUT jack to cut the feedback.Then set t

26STICKING LABELSAfter the connection and settings, stick the supplied labels on the front panel of the unit.The labels indicate the following:• Name

27 Indication of Input Line Assigned to SUB OUTDraw a line between SUB OUT and the assigned input connector, or black out the square.The assigned inp

28ATTACHING/DETACHING THE ACRYLIC COVERThe input levels need to be adjusted before using the unit.After the adjustments, attaching the supplied acryli

29 Basic OperationThis section describes basic operation. All setup items and connections must be completed in advance.The switches located under the

3Wij verklaren als enige aansprakelijke, dat het product waarop dezeverklaring betrekking heeft, voldoet aan de volgende normen of anderenormatieve do

30 Input Level AdjustmentThis section describes how to adjust input levels.The figure describes an example. • Mode 1• The microphone is connected to

31 Using CD/MD Player through LINE INThis section describes amplification when a CD player orMD player, etc. is connected to the LINE IN jack at the f

32BLOCK DIAGRAMHPFSENSSENSMONO 1MULTI INMONOMULTI INSTLINE IN(FRONT PANEL)HPFMONO 2HPFMONO 3HPFMONO 4ST 1MUTE SENSEREAR PANEL SWST 2ST 3ST 4SUB INMute

33HPFSENSSENSMONO 1MULTI INMONOMULTI INSTLINE IN(FRONT PANEL)HPFMONO 2HPFMONO 3HPFMONO 4ST 1MUTE SENSEREAR PANEL SWST 2ST 3ST 4SUB INMuteSTEREOMONOSUB

34 MODE 2HPFSENSSENSMONO 1MULTI INMONOMULTI INSTLINE IN(FRONT PANEL)HPFMONO 2HPFMONO 3HPFMONO 4ST 1MUTE SENSEREAR PANEL SWST 2ST 3ST 4SUB INMuteSTERE

35 MODE 3HPFSENSSENSMONO 1MULTI INMONOMULTI INSTLINE IN(FRONT PANEL)HPFMONO 2HPFMONO 3HPFMONO 4ST 1MUTE SENSEREAR PANEL SWST 2ST 3ST 4SUB INMuteSTERE

36LEVEL DIAGRAM+30+20+100–10–20–30–40–50–60–70–80–90–100–110–120–130(dBu)+30+20+10–10–20–30–40–50–60–70–80–90–100–110–120–130(dBu)ST "10"MON

37TroubleCheck item RemedyPower does not turn on.No sound is heard from thespeakers connected to SUBOUTPUT.The power cord insulation isdamaged.The pow

38● Basic SpecificationsPower supply 120 V AC, 60 Hz or 220 V to 240 V AC, 50 Hz*Power consumption 10 WTemperature range 0 °C - +45 °C (32 °F - 113 °F

Na0402-0 3TR001013AAA Printed in ChinaN 192002 © Matsushita Communication Industrial Co., Ltd. All rights reserved.Panasonic Canada Inc.5770 Ambler D

41) Read these instructions.2) Keep these instructions.3) Heed all warnings.4) Follow all instructions.5) Do not use this apparatus near water.6) Clea

5CONTENTSIMPORTANT SAFETY INSTRUCTIONS ...4PREFACE ...

6This audio mixer has four mono input lines, four stereo input lines, one mono/stereo input line and three output lines.FEATURES● Three modes applicab

7PRECAUTIONS• Refer all work related to installation of this productto qualified service personnel or system installers.• Turning On the PowerTurn on

8MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS Front Viewq Power switch [POWER]Toggles the power on and off.w Power indicatorLights up when the power

9!0Input peak indicator [INPUT PEAK]Lights up when any input signal reaches –3 dB (fromthe MONO INPUT 1 to 4 connectors, the STEREOINPUT 1 to 4 jacks