Panasonic DMPBD85 User Manual download pdf (Page 34)

VQT2H79

Messages

The following messages or service numbers appear on the

television or unit’s display when something unusual is

detected during startup and use.

Cannot play.

You inserted an incompatible disc.

Cannot play on this unit.

You tried to play a non-compatible image.

Confirm “SD” on the unit’s display is not blinking and

re-insert the card.

No disc is inserted.

The disc may be upside down.

$ This operation is not available.

Some operations are unsupported by the unit. For

example;

– BD-Video: During playback, reverse slow-motion or

reverse frame-by-frame is not possible.

IP address is not set.

The “IP Address” in “IP Address / DNS Settings” is “---. ---.

---. ---”. Set the “IP Address”, “Subnet Mask”, and

“Gateway Address”. (Select the automatic address

acquisition if necessary.)

The current security setting of Wireless LAN

is low. It is recommended to change the

setting.

Authentication type for the Wireless LAN is set to “Open

system”, or the encryption type is set to “No encryption”. It

is recommended to encrypt for safety reasons. For

details, refer to the instructions of the Wireless router

being used. Encryption is required when playing back

video, etc., from DLNA compatible devices.

F99

The unit fails to operate properly. Press [Í/I] on the main

unit for 3 seconds to switch the unit to standby, then

switch back on.

HDMI ONLY

Some BD-Video discs can only be output with HDMI.

NET

Displays while VIERA CAST is starting up.

No PLAY

There is a viewing restriction on a BD-Video or

DVD-Video. (> 28)

No READ

The media is dirty or badly scratched. The unit cannot

play.

PLEASE WAIT

The unit is carrying out internal process.This is not a

malfunction. You cannot operate the unit while “PLEASE

WAIT” is displayed.

REMOVE

The USB device is drawing too much power. Remove the

USB device.

SET 

(“  ” stands for a number.)

The remote control and main unit are using different

codes. Change the code on the remote control.

Press and hold [OK] and the

indicated number button at the

same time for more than 5

seconds.

U59

The unit is hot.

The unit switches to standby for safety reasons. Wait for

about 30 minutes until the message disappears.

Select a position with good ventilation when installing the

unit. Do not block the ventilation hole on the rear and side

of the unit.

U72

U73

The HDMI connection acts unusually.

– Turn the unit and TV off.

– Disconnect the HDMI cable between the player and the

TV.

– Please use HDMI cables that have the HDMI logo.

– The connected equipment may not be compatible. If

connecting through an amplifier/receiver, try connecting

directly to the TV to see if message clears.

H or F

(“  ” stands for a number.)

There is something unusual.

Check the unit using the troubleshooting guide. If the

service number does not disappear, do the following.

1 Disconnect the plug from the household mains socket

wait a few seconds, then reconnect it.

2 Press [Í/I] to turn the unit on. (The unit may be fixed.)

If the service number does not disappear despite doing the

above, request service from the dealer. Inform the dealer of

the service number when requesting service.

START

The system is being restarted during the firmware update.

Please do not turn off the unit

UPD/

(“  ” stands for a number.)

The firmware is being updated.

Please do not turn off the unit.

FINISH

The firmware update is complete.

On the television

On the unit’s display

DMP-BD85EB&EG-VQT2H79_eng.book 34 ページ２０１０年１月１５日　金曜日　午後６時４６分

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 43 44

Comments to this Manuals

No comments

Panasonic DMPBD85 User Manual Page 34

Comments to this Manuals

Related products and manuals for Blu-Ray players Panasonic DMPBD85