Panasonic RXES29 User Manual download pdf (Page 7)

RQT7967

The Radio

Preparation:

≥ When using batteries, press [].

≥ Press [TUNER BAND] to select “FM” or “AM”.

Manual tuning

[1]

Press [REW/–/

] or [

/+/FF] to select a station.

To tune automatically

Press and hold [REW/–/6] or [5/+/FF] until the

frequency starts changing rapidly.

≥ Auto tuning may be interrupted when there is excessive

interference.

≥ To cancel auto tuning, press [REW/–/6] or

[5/+/FF] once again.

[2] Press [+, – VOLUME] to adjust volume.

To use auto scan

You can search for a station by listening to all tuned-in stations

for 8 seconds each.

[1] Press [AUTO SCAN].

[2] Press [AUTO SCAN] when you find the desired

station.

Auto scan ends when it reaches the original frequency again.

To stop during the process, press [AUTO SCAN].

To improve FM sound quality

Press [PLAY MODE] to display “ ”.

Monaural sound is selected and noise reduces when reception is weak.

Press [PLAY MODE] again to cancel the mode.

≥ To improve reception

FM : Change the length and direction of the antenna.

AM : Change the direction of the unit.

≥

AM reception is briefly interrupted if [< DECK] is pressed.

≥

To improve reception when using the unit in a building or

vehicle, place it near a window.

To receive FM broadcasts allocated in 0.1MHz

Main unit only

First press [TUNER BAND] to select “AM”. Now, press and

hold [TUNER BAND]. The display changes in a few seconds to

show the current lowest FM frequency. Continue to hold down

the button. The minimum frequency changes and the step is

changed at the same time. Changing the step erases all preset

stations. Repeat the above to change the step back.

Preset tuning

Up to 16 stations can be set in the FM and AM band.

[1] Press [REW/–/6] or [5/+/ FF] to tune to the

required station.

[2] Press [ MEMORY CLEAR].

[3] While “ ” is flashing

Turn [TIME/PRESET TUNE TRACK SKIP ] to select the

channel and press [ MEMORY CLEAR] or on remote control,

press the numeric buttons to select channels.

≥ For channels 1 to 9, press the corresponding number.

≥ For channels 10 to 16, press [S10], then the two digits.

If “ ” goes off during presetting, return to step [1].

To select channels

Turn [TIME/PRESET TUNE TRACK SKIP ] to

select the channel or on remote control, press the

numeric buttons to select channels.

To use preset scan

You can search for a station by listening to all preset channels

for 8 seconds each.

[1] Press and hold [C/: ALBUM] or [ALBUM 9/

D] until “PS” appears on the display.

[2] Press [C/: ALBUM] or [ALBUM 9/D] when

you find the desired channel.

Preset scan ends after searching through each preset channel

once. To stop during the process, press

[C/: ALBUM] or

[ALBUM 9/D].

To skip the preset channel,

1 Select the desired station.

2 Press [MEMORY CLEAR].

3 While “ ” is flashing

Turn

[TIME/PRESET TUNE TRACK SKIP ]

to display “– –”.

4 Press [ MEMORY CLEAR].

To select the skipped channel,

Press the numeric buttons.

LUME

REW

POWER

OWER

POWER

AMFM

RX-ES29-ad.book 7 ページ２００５年３月２３日　水曜日　午後５時４７分

1 2 3 4 5 6 7 8 9 10 11 12 ... 17 18

Comments to this Manuals

No comments

Panasonic RXES29 User Manual Page 7

Comments to this Manuals

Related products and manuals for Cassette players Panasonic RXES29