Panasonic VLWD812EX User Manual download pdf (Page 2)

How to connect the power cable (AC/DC)

Attach to the DIN rail

Attach in the order described below so that hook (b) is positioned at the bottom.

Hang hook (a) on the DIN rail (

Pull and hold the lever down (

Secure hook (b) to the DIN rail (

Hook (a)

Hook (b)

Installing the power supply unit and camera

Important:

● Register the camera to the main monitor station before installation. ( reverse side)

● Do not attach to a ceiling.

● Do not install in areas directly exposed to water or rain.

● Holes must be made in the wall for cables and wires to pass through. Panasonic takes no

responsibility for issues related to opening holes in walls.

● Make sure to waterproof the holes made in walls.

● Make sure you use the safety wire attached to the camera to prevent the camera from

falling.

● Required pull-out capacity of a single screw is 294 N {30 k

f} or more. If this criteria is not

met, make sure to take additional measures to increase strength.

● Do not use an impact driver. (This may lead to damaged screws or over tightening.)

Install the power supply unit

Install the camera (continued)

If connecting an external sensor

Open the cover on the rear and connect the DC cable.

Attach the wall mount bracket to the wall that has the cable access hole and

caulk the bracket.

Pass the DC cable through the recessed area

of the water-resistant rubber and attach the

cable.

2-1 Open the cover. 2-2 Strip the DC cable.

2-3 Remove the water-resistant rubber (A) from the camera and attach it to the DC

cable.

2-4 Loosen the screws (

B) and push in the wires

of the DC cable to the terminal connectors

(non-polar), then tighten the screws.

● Recommended torque:

0.8 N·m {8.2 k

f·cm}

● Secure the water-resistant rubber attached to

the cable to its original position.

1-1 Secure the wall mount bracket.

Install the camera

1-2 Use a water-resistant seal-

ant to caulk around the

bracket, except for the bot-

tom part.

● Mount the wall mount bracket so that the "

UP" mark faces up, and caulk as shown

here, making sure to ll in any gaps.

(If the bracket is not properly waterproofed, water may enter, which may result in fire

or electric shock.)

1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan

http://www.panasonic.net/

PNQW3991ZA PC1113MT1113

12 mm

32 mm

● Insert the wires while pressing the terminal buttons with the tip of a screwdriver.

Connect wires to the external input terminal.

● Refer to "About the external input terminal" on the reverse side and connect the wires

properly.

3-1 Strip the wires.

● Refer to 2-2 of step 2 for stripping wires.

3-2 Remove the water-resistant rubber (

from the camera and attach it to the

wires.

● Refer to the drawing in 2-3 of step 2.

3-3 Connect the wires to the terminals (

D) and reattach

the water-resistant rubber and secure it in its original

position.

Close the cover (push closed until it clicks).

● After attaching the 4 screws

(accessory), attach the screw covers.

● Recommended torque:

1.2 N·m {12.2 k

f·cm}

Screws

(accessory)

Washer (accessory)

Safety

wire

Screw covers

(accessory)

Mounting screw

(locally procured)

Attach the camera to the wall mount bracket and secure it.

Adjusting the camera angle.

View when looking from below

● Recommended torque for screw

: 0.7 N·m {7.1 k

f·cm}

Adjusting angle left and right:

1. Loosen screw A and adjust the

angle left or right.

2. Tighten screw

1. Hold the camera in one hand and

loosen screw

B to adjust the angle up

or down.

2. Tighten screw

Adjusting angle up and down:

Turn on the camera, monitor the camera image, conrm the viewable area and the

camera audio. (

Operating Instructions of the Video Intercom System)

● If you’re not satised with the viewable area, adjust the camera angle and conrm the

results.

● If the Video Intercom System includes a sub monitor, take it to the camera installation

location and conrm the image displayed on the sub monitor while adjusting the camera

angle as necessary.

● Attach the safety wire high on the wall so

that the camera does not strike anyone in

the event the camera becomes detached

from the wall.

● Do not hang from the camera.

After you have adjusted the angle,

attach the safety wire to the wall.

Test the sensor detection and image recording. ( at right)

Lift the tab

to open the

cover

Water-resistant rubber

Cover

It is difficult to tighten the screw when the

camera is facing forward. Using the meth-

od shown to the right, tighten the screw

after rotating the camera body to the left or

right.

When tightening screws

View when looking

from below

Loosen this screw

and move the camera

left or right

Screw A

Screw B

When using the heat sensor

Using the sensor range caps Changing the angle of the heat sensor

If there are objects that you do not want the heat sensor to detect, you can limit the detectable

area by attaching the sensor range caps.

You can use the heat sensor adjustment lever on the camera to set the heat sensor to one

of two positions.

■ Sensor range cap types and detection range

In addition to the standard cap (already attached to the camera), there are four cap types

(caps 1-4). Each cap prevents a different area from being detected and can be attached

at 45-degree increments. Refer to the following and attach the proper cap at the proper

angle.

● The detection area is an approximation for when the [Heat sensor sensitivity] setting

(

"Changing the sensitivity of the heat sensor", below right) is set to [Normal].

(Varies by ambient temperature at camera installation location)

(Example 1)

When there is an object on the right side of

the viewable area that you do not want to

be detected (house next door, street, etc.).

Attach one of caps 1-3 as shown on the right

according to the area you do not want to be

detected.

(Example 2)

When there is an object in the top left of

the viewable area that you do not want

to be detected (cars in a street, etc.).

■ Removing and attaching sensor range caps

When removing:

Use the thick end of the cap removement tool (accessory) to remove.

When attaching:

Rotate the tab on the cap toward the

top or at a 45-degree angle according to

the type of cap or direction, and attach

the cap on the camera as shown on the

right.

Attach one of caps 1-3 as shown

above according to the area you

do not want to be detected

① ② ③

When using motion detection

Changing the detection range of the motion detection sensor

Changing the sensitivity of the motion detection sensor

Use the main monitor to change the camera’s [Motion detection range] setting.

● By setting the areas that you do not want motion to be detected from the 12 blocks shown in

the screen below, you can narrow down the areas that motion can be detected in.

Use the main monitor to change the camera’s [Motion detection sensitivity] setting. (You can

adjust the amount of motion that will be detected by setting the sensitivity setting.)

■ Motion detection sensitivity setting (4 levels)

● High sensitivity

● Normal (default setting)

● Low sensitivity

● Very low sensitivity

Changing the setting (Example: Video Intercom System VL-SWD501EX series)

Use the main monitor settings, select [Connected devices] → [Camera] → camera number

→ [Sensor settings] → [Motion detection range] → the areas not subject to detection from

the 12 blocks, and then touch [Configure].

(Example) When checking motion detection performance, a car in the street that

you do not want to be detected is displayed in the top of the screen

In the motion detection range screen, select the area containing the street that you do not

want to be detected.

Adjusting sensor sensitivity and detection range

Note:

● When [High sensitivity] is selected, it is more likely that wind or objects outside the

viewable area will cause detections. (Use this setting only when the installation

environment absolutely requires it)

Use the main monitor to change the camera’s [Heat sensor sensitivity] setting.

(

The heat sensor’s range of detection varies by the selected sensitivity.

)

■ Heat sensor sensitivity and detection range

The detection range shown below is an approximation. (Varies by ambient temperature

and environment of installation location)

High sensitivity:

Low sensitivity:

Normal (default setting):

■ Lever position and sensor detection range

The detection range shown below is an approximation. (Varies by ambient temperature

and environment of installation location)

At time of purchase:

When lever is raised:

Changing the sensitivity of the heat sensor

Use the main monitor settings, select [Connected devices] → [Camera] → camera

number → [Sensor settings] → [Heat sensor sensitivity] → the sensitivity from the 4 lev-

els.

Changing the setting (Example: Video Intercom System VL-SWD501EX series)

Very low sensitivity:

Ambient temperature: 20 °C

Use the main monitor settings, select [Connected devices] → [Camera] → camera

number → [Sensor settings] → [Motion detection sensitivity] → the sensitivity from the 4

levels.

Changing the setting (Example: Video Intercom System VL-SWD501EX series)

Cap type

Approximate detection range (view when looking from above)

20 ºC 0 ºC 30 ºC

Standard (attached

to camera)

Cap 1

(Example) Cap 1 (Example) Cap 1 (Example) Cap 1

Cap 2

(Example) Cap 3 (Example) Cap 3 (Example) Cap 3

Cap 3

When you want

to make one side

not detectable

Cap 4

When you want to

make both sides

not detectable

● The detection range rotates according to the sensor range cap angle.

Motion will not be detected in areas

with an "X".

Configure

>>>>>>Motion detection range

Touch the areas that you do not

want to detect motion for.

If you want to detect small changes in

motion, select [High sensitivity], and select

[Low sensitivity] or [Very low sensitivity] if you

want to detect only drastic changes in motion.

Detection

range

About 5 m

About 6 m

About 4 m

Detection

range

Example 1

Example 2

Detection

range

Tab

About 6 m

About 5 m

About 4 m

About 3 m

Detection

range

Detection

range

Detection

range

Detection

range

View from above

Lever

At time of purchase:

When the lever is raised:

Viewable area

Detection range

Viewable area

Detection range

Confirming sensor detections

From the top menu of the main monitor, touch → →

[Connected devices] → [Camera] → camera number → [Sensor settings] →

[Check sensors] → tap each type of sensor to confirm.

You must trigger the

sensor at the camera

within about 20 minutes.

To end the operation, press

Use the main monitor to confirm the detections made by the heat sensor or motion detection.

● The operations described here are based on the VL-SWD501EX series main monitor. See the

Operating Instructions of the Video Intercom System for more information.

● When sensors make a detection

–

The camera’s LED lights and indicator lamp

ash.

–

The display on the main monitor changes as

shown to the right according to the sensor type

selected in step 1.

Note:

● The camera image turns off automatically after about 20 minutes when conrming the sensor. If

20 minutes pass while conrming, start over from the beginning.

● You can also use the above procedure to conrm a commercially available external sensor, if

connected.

When detections are not made correctly or when incorrect detections are made

■ When detections are not made prop-

erly

Refer to "Adjusting sensor sensitivity and

detection range" (

at right) and make

adjustments as explained below.

Heat sensor:

● Change the [Heat sensor sensitivity]

setting (increase sensitivity)

Motion detection:

● Change the [Motion detection sensitivity]

setting (increase sensitivity)

■ When incorrect detections are made

Refer to "Adjusting sensor sensitivity and

detection range" (

at right) and make

adjustments as explained below.

Heat sensor:

● Use the sensor range caps

● Change the angle of the heat sensor

● Change the [Heat sensor sensitivity]

setting (decrease sensitivity)

Motion detection:

● Change the [Motion detection sensitivity]

setting (decrease sensitivity)

● Change the [Motion detection range]

setting (change the range)

Testing the sensor detection images

Confirm if images are correctly recorded before and after images are recorded for sensor detections.

● The operations described here are based on the VL-SWD501EX series main monitor. See the

Operating Instructions of the Video Intercom System for more information.

From the top menu of the main monitor, touch → →

[Connected devices] → [Camera]→ camera number → [Sensor settings] →

[Recording test].

You must trigger the

sensor at the camera

within about 20 minutes.

When recording ends, touch [Result] and

confirm the recorded images (A-D).

To end the operation, press

● A screen such as the one shown on

the right is displayed on the main

monitor, and images from when the

detection occurred are retained (up

to 4 still images).

● Touch an image (

) to display it full-

screen.

● To perform a recording test again, touch

in the screen shown to the right,

and touch [Test again] when the screen

in step 3 is displayed.

When using default setting:

Image from 1 second before detection

B to D: Images from time of detection

until about 2 seconds after detection

You can use the

[Recording before detection] setting to

retain images from up to 2 seconds before

the detection. (

Operating Instructions

of the Video Intercom System)

The sensor name is displayed for

about 1 second. When the sen-

sor is triggered again, the name is

displayed.

■ Confirm with a subject that you want

to detect

Check whether the sensor is triggered at the

location where you want to detect movement,

with people moving in the direction you want

to detect.

■ Confirm with a subject that you do not

want to detect

Check whether the sensor is not triggered by

subjects that you do not want to detect, such

as people or cars moving on a street.

● The camera waits for the sensors to be triggered and live images from the camera are

displayed.

Motion detection:

Heat sensor:

Heat sensor

Motion detection

Area that motion was detected in (shown in yellow)

Displayed when recording is complete

Live image

(Example) When the heat sensor

makes a detection

ヒ

ヵㄆㄔㄕチ㄂ㄈ㄂ㄊㄏ

ンㄆㄔㄖㄍㄕ

ラㄆ㄂ㄕチㄔㄆㄏㄔㄐㄓ

Result

①

②

③

④

Name of sensor which made the detection

Confirm the displayed message and then touch [Next].

● The camera waits for the sensors to be triggered.

■ About the installation location

● The device must be installed inside an electrical panel or cabinet.

● A readily accessible disconnect device shall be incorporated external to the equipment.

- External disconnect device must be certied and have a creepage and clearance

distance of 3 mm or more.

■ Precautions for wiring

● Make sure you turn off the power at the breaker before performing any wiring work.

● Always connect AC or DC cables to the appropriate connection terminals. Incorrectly

connecting the AC or DC cables may damage the power supply unit.

● To prevent the power cables from disconnecting and to prevent electric shock, secure the

power cables using the cable binders (accessory) and attach the cable covers.

CAUTION

Insert the cables firmly all the

way into the terminals.

If the cables are not inserted all

the way, heat may be generated.

*1 Make sure that there are no bare wires

exposed outside the product.

Connect the power supply unit (accessory) and AC/DC cables (locally procured).

Strip the AC/DC cables as follows:

7 mm

45 mm

25 mm

7 mm

Remove the screws (

) and then remove

the cable covers (

Connect the AC/DC cable to the AC IN

terminal/DC OUT terminal on the top and

bottom of the power supply unit, and then

secure the wires by tightening the screws.

● Recommended torque:

- AC terminal: 0.4 N·m {4.1 kgf·cm}

- DC terminal: 0.45 N·m {4.6 kgf·cm}

220-240 V AC

AC cable

DC cable

24 V DC

Screws

Cable binders (accessory)

Use the cable binders (accessory) to secure

the AC/DC cables (double-coated area) to

the power supply unit.

Make sure to replace the cable covers (

DC OUT terminal

AC cable

binder hole

AC IN terminal

DC cable

binder hole

Cable covers (

)

Screws (

)

Mounting screws

(locally procured) × 4

Vertical, flat wall

46 mm

83.5 mm

Cable access

hole

DC cable

Water-

resistant

sealant

Wall mount

bracket

Configure

>>>>>>Motion detection range

Touch the areas that you do not

want to detect motion for.

The bottom part of the bracket

has a water drain hole on it; do

not caulk it

Power supply unit (with cable covers

removed)

1 2

Comments to this Manuals

No comments

Panasonic VLWD812EX User Manual Page 2

Comments to this Manuals

Related products and manuals for Cool boxes Panasonic VLWD812EX