Panasonic TH42PA60E Operations Instructions Page 16

  • Download
  • Add to my manuals
  • Print
  • Page
    / 16
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 15
FAQs, etc.
30
31
Licence
Trademark Credits
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
FAQs
Specifications
Note
Design and Specifications are subject to change without notice. Weight and Dimensions shown are approximate.
This equipment complies with the EMC standards listed below.
EN55013, EN61000-3-2, EN61000-3-3, EN55020.
TH-37PA60E TH-42PA60E
Power Source
AC 220-240 V, 50 / 60 Hz
Power
Consumption
Average use 206 W 238 W
Standby condition 0.3 W
Plasma Display
panel
Drive method AC type
Aspect Ratio 16:9
Contrast Ratio Max 10000:1
Visible screen size
(No. of pixels)
94 cmV 106 cmV
818 mm (W) × 461 mm (H) ×
939 mm (diagonal)
920 mm (W) × 518 mm (H) ×
1,056 mm (diagonal)
408,960 (852 (W) × 480 (H)) [2,556 × 480 dots]
Sound
Speaker
12 cm × 6 cm × 2 pcs, 8
Audio Output 20 W (10 W + 10 W), 10% THD
Receiving Systems /
Band name
PAL B, G, H, I, SECAM B, G, SECAM L / L
VHF E2 - E12 VHF H1 - H2 (ITALY)
VHF A - H (ITALY) UHF E21 - E69
CATV (S01 - S05) CATV S1 - S10 (M1 - M10)
CATV S11 - S20 (U1 - U10) CATV S21 - S41 (Hyperband)
PAL D, K, SECAM D, K
VHF R1 - R2 VHF R3 - R5
VHF R6 - R12 UHF E21 - E69
PAL 525/60 Playback of NTSC tape from some PAL Video recorders (VCR)
M.NTSC Playback from M. NTSC Video recorders (VCR)
NTSC (AV input only) Playback from NTSC Video recorders (VCR)
Aerial - Rear VHF / UHF
Operating Conditions
Temperature : 0 °C - 40 °C
Humidity : 20 % - 80 % RH (non-condensing)
Connection Terminals
AV1 (Scart terminal) 21 Pin terminal (Audio/Video in, Audio/Video out, RGB in)
AV2 (Scart terminal) 21 Pin terminal (Audio/Video in, Audio/Video out, S-Video in, Q-Link)
AV3 (Scart terminal) 21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, S-Video in, Q-Link)
Others
COMPONENT
Y 1.0 V[p-p] (including synchronization)
PB, PR ±0.35 V[p-p]
HDMI TYPE A Connector
AUDIO L - R RCA PIN Type × 2 0.5 V[rms]
Output AUDIO L - R RCA PIN Type × 2 0.5 V[rms] (high impedance)
Dimensions ( W × H × D )
968 mm × 641 mm × 97 mm (TV Set only)
968 mm × 704 mm × 320 mm (With Pedestal)
1,068 mm × 701 mm × 97 mm (TV Set only)
1,068 mm × 764 mm × 320 mm (With Pedestal)
Weight
25.0 k Net (TV Set only)
27.0 k Net (With Pedestal)
29.0 k Net (TV Set only)
31.0 k Net (With Pedestal)
Licence / Specifications
Frequently Asked Questions
Problem Actions
Screen Sound OtherHDMI
Chaotic image, noisy
Set "P-NR" in the Picture menu (to remove noise).
(p. 14)
Check nearby electrical products
(car, motorcycle, fluorescent lamp).
Blurry or
distorted image
(no sound or low volume)
Reset channels. (p. 18)
No image can be
displayed
Is "Colour" or "Contrast" in the Picture menu set to the
minimum? (p. 14)
Neither image nor
sound is produced
Is the unit in "AV mode"?
Is the mains lead plugged into the socket outlet?
Is the TV unit turned On?
Check Picture menu (p. 14) and volume.
No sound is produced
Is "Sound Mute" active? (p. 7)
Is the volume set to the minimum?
Sound is unusual
Set the sound setting of the connected equipment
to "2ch L.PCM".
Check the "HDMI input" setting in the Sound menu.
(p. 14)
If digital sound connection has a problem, select
analogue sound connection. (p. 27)
Sound level is low
or sound is distorted
Sound signal reception may be deteriorated.
Set "MPX" (p. 14) in the Sound menu to "Mono".
TV unit goes into
"Standby mode"
The sleep function is activated.
The TV unit enters "Standby mode" about 30 min.
after broadcasting ends.
An error message
appears
Follow the message's instructions.
If the problem persists, contact the authorized
Service Centre.
An error message
appears
Contact the authorized Service Centre.
"
Control with HDMI
"
function does not work
Switch the TV unit on again with the equipment on.
Set "Control with HDMI" to "Off", then set to "On" again.
(p. 21)
Page view 15
1 2 ... 11 12 13 14 15 16

Comments to this Manuals

No comments