®PLASMA DISPLAYTQBC0937Please read these instructions before operating your set and retain them for future reference.EnglishTH-65PHD7WHigh Definition
10SERIAL Terminals connectionNotes:• Use the RS-232C cable to connect the computer to the Plasma Display.• The computer shown is for example purposes
11ConnectionsAV and COMPONENT connectionSLOT2 SLOT3VIDEO INVIDEO OUTPR/CR/R PB/CB/BY/GAUDIORLCOMPONENT/RGB INAUDIOINR LAVS VIDEO INSLOT1PC INVIDEOO
12Power On / OffConnecting the plug to the Wall OutletNote:Main plug types vary between countries. The power plug shownat right may, therefore, not be
13Press to display the Setup menu.Press to select your preferred language. Selectable languagesPress to select the OSD Language.Notes:• Selecting is a
14PC buttonPress the “PC” input mode selection button to selectthe PC input mode.This button is used to switch directly to PC input mode.Note:After-im
15PLASMA DISPLAYINPUTSURROUNDVOLNRPICTURESOUNDSET UPASPECTPICTUREPOS. /SIZEOFF TIMERPCMULTIPIPSWAP SELECT MOVEZOOMBasic ControlsSURROUND buttonThe sur
16PLASMA DISPLAYINPUTSURROUNDVOLNRPICTURESOUNDSET UPASPECTPICTUREPOS. /SIZEOFF TIMERPCMULTIPIPSWAP SELECT MOVEZOOMINPUT MENU ENTER–+VOLOn-Screen Menu
172 Press toaccess eachadjust screen.Press the R button to return toprevious menu screen.Note: “Signal” setup menu displays different setting conditio
18ASPECTASPECT ControlsThe Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinemaformat picture.
19Adjusting Picture Pos. / Size1Press to display the Picture Pos. /Size menu.Press to adjust Pos. / Size.Press to exit from adjust mode.Press to selec
2Table of ContentsDear Panasonic CustomerWelcome to the Panasonic family of customers. We hope that you will have many years ofenjoyment from your new
20MULTI PIPMULTIPIPMULTIPIPMULTIPIPABABABBABABAPC1VIDEO1SELECTSWAP SWAP SWAPPC1VIDEO1VIDEO2VIDEO1PC1VIDEO3AAACBBBDMULTIPIPSWAPSELECTZOOMMOVEINPUTSURRO
211/2PictureNormalNormaliseNormal250003BrightnessSharpnessPicture ModeColourContrastTint2/2PictureAdvanced settingsWhite balanceColour ManagementNorma
22DetailsAdjusts the dark shades of the image in gradiation.Adjustment of parts which are extremely bright and hard to see.(This cannot be adjusted wh
23SoundNormalNormaliseNormal000OffTrebleSound ModeBalanceBassSurroundSound Adjustment1Press to display the Sound menu.MuteUseful when answering the ph
24Digital Zoom1324This displays an enlargement of the designated part of the displayed image.Display the “Operation Guide”.Press to access Digital Zoo
25PRESENT TIME Setup / Set up TIMERThe timer can switch the Plasma Display On or Off.Before attempting Timer Set, confirm the PRESENT TIME and adjust
26Set up TIMERPress to setupPOWER ON Time / POWER OFF Time. button: Forward button: BackNotes:• Pressing “ ” or “ ” button once changes POWER ON Time
27Reversal / Scroll selectionScreensaver (For preventing after-images)Do not display a still picture, especially in 4:3 mode, for any length of time.I
28Screensaver (For preventing after-images)Setup of Screensaver TimePress to select Start Time / Finish Time(When Time Designation is selected).Press
29Side Panel Adjustment1Press to select Side panel.Press to select Off, Low, Mid, High.Press to exit from Screensaver.2Do not display a picture in 4:3
3Important Safety NoticeCAUTIONThis appliance is intended for use in environments which are relatively free of electromagnetic fields.Using this appli
30Reduces power consumptionPress to select “On” or “Off”.Press to select“Power save”“Standby save”“Power management”“Auto power off”.• Power save: Whe
31Setup for MULTI DISPLAYBy lining up Plasma Displays in groups of 4, 9 or 16 as illustrated below, an enlarged picture may be displayed acrossall scr
32Press to select Ratio (2nd step).Press to select “2 × 2”, “3 × 3”, “4 × 4”.How to set the display location number for each Plasma DisplayPress to se
33Setup for Input SignalsComponent / RGB-in selectSelect the input signals to be connected by installing the Optional Terminal Board.(Refer to the Ope
34Setup for Input SignalsColour system / Panasonic AutoSelect Signal from the “Setup” menu during AV(S Video) input signal. (“Signal[AV]” menu is disp
35Select Signal from the “Setup” menu during RGB input signal.Press to adjust.Setting RGB sync signal:Confirm that the input is set to RGB input (this
36Shipping conditionThis function allows you to reset the unit to the factory setting.SET UP12341/2SignalPCOffStandby saveOffPower managementOffAuto p
37SymptomsPicture SoundTroubleshootingBefore you call for service, determine the symptoms and make a few simple checks as shown below.This Plasma Disp
38VIDEO/COMPONENT/RGB/PC input signalsVIDEO input [Applicable when Multi Screen and Digital Zoom]Signal nameHorizontal Verticalfrequency(kHz) frequenc
39Note:Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.SpecificationsPower SourcePower Consu
4Safety PrecautionsWARNING SetupThis Plasma Display is for use only with the following optional accessories. Use with any other type of optionalaccess
Customer’s RecordThe model number and serial number of this product can be found on its back cover. You should note this serialnumber in the space pro
5Safety Precautions When using the Plasma DisplayThe Plasma Display is designed to operate on 220 - 240 V AC, 50/60 Hz.Do not cover the ventilation ho
6 CAUTION When using the Plasma DisplayDo not bring your hands, face or objects close to the ventilation holes of the Plasma Display.• Heated air come
7PLASMA DISPLAYINPUTSURROUNDVOLNRPICTURESOUNDSET UPASPECTPICTUREPOS. /SIZEOFF TIMERPCMULTIPIPSWAP SELECT MOVEZOOMAccessoriesAccessories SupplyCheck th
812SERIALPC INAUDIOSLOT1 SLOT2 SLOT3VIDEO INVIDEO OUTPR/CR/R PB/CB/BY/GAUDIORLCOMPONENT/RGB INAUDIOINR LAVS VIDEO IN1321212ConnectionsWhen connecti
9ConnectionsPC Input Terminals connectionNotes:• Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz a
Comments to this Manuals