Panasonic PT-D10000E User Manual Page 79
- Page / 122
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Special Features
ENGLISH – 79
of the lamps.
Yellow: An error has occurred with the illumination
of one or more of the lamps
White: Unselected item
Red: Lamp where an illumination error has
occurred
Lamp relay
If using the projector for a continuous period of
24 hours or more, this setting can be used to
automatically switch the lamps that are turned on in
order to reduce the lamp deterioration that can occur
as a result of continuous use.
“LAMP RELAY” will only be enabled when the lamp
selection is “SINGLE” (1 lamp), “DUAL” (2 lamps),
“TRIPLE” (3 lamps) or “QUAD” (4 lamps).
1. Press ▲▼ to select “LAMP
RELAY”.
2. Press ◄► to switch “LAMP
RELAY”.
The time interval for lamps to be switched will
change as shown in the diagram below each
time ◄► is pressed.
Note
If the lamp selection is changed, picture is muted
during lamp switching execution. (7-25 sec.)
The lamps will switch at the specified time when the
lamp selection is “SINGLE” or “DUAL”.
When the lamp selection is “TRIPLE”, the lamps will
switch a total of three times at two-hour intervals
starting from the specified time, and after this the
previous operating status will be maintained until the
next specified time is reached.
When the lamp selection is “QUAD”, three lamps
will illuminate from the specified time, and the three
lamps will switch a total of four times at two-hour
•
•
•
•
•
•
OPTION2
PROJECTOR ID
INSTALLATION
ALTITUDE
DIRECTION
LAMP SELECT
LAMP RELAY
RS-232C
SYSTEM INFORMATION
AIR FILTER CLEANING
DATE AND TIME
STARTUP LOGO
PASSWORD
MENU SELECT
CHANGE
2
FRONT-F
LOW
H
QUAD
OFF
LOGO1
OPTION2
PROJECTOR ID
INSTALLATION
ALTITUDE
DIRECTION
LAMP SELECT
LAMP RELAY
RS-232C
SYSTEM INFORMATION
AIR FILTER CLEANING
DATE AND TIME
STARTUP LOGO
PASSWORD
MENU SELECT
CHANGE
2
FRONT-F
LOW
H
QUAD
OFF
LOGO1
(Units of 1 hour)
OFF
00:00
23:00
01:00
(Units of 1 hour)
OFF
00:00
23:00
01:00
intervals from that time. After this, four lamps will
illuminate for eight hours from the specified time,
and then when the next specified time is reached,
switching between three lamps will resume.
The setting time will be the local time. (p. 81)
RS-232C setting
This sets communication parameters for the projector.
1. Press ▲▼ to select “RS-232C”.
2. Press ENTER.
The “RS-232C” screen will be displayed.
3. Press ▲▼ to select “SERIAL
IN”.
4. Press ◄► to switch “SERIAL
IN”.
The setting will change as follows each time
◄► is pressed.
RS-232C RS-422
5. Press
▲▼ to select
communication conditions.
6. Press ◄► to confirm the setting.
7. Press MENU three times.
The on-screen indications disappear, and the
system returns to the normal screen.
•
•
•
•
OPTION2
PROJECTOR ID
INSTALLATION
ALTITUDE
DIRECTION
LAMP SELECT
LAMP RELAY
RS-232C
SYSTEM INFORMATION
AIR FILTER CLEANING
DATE AND TIME
STARTUP LOGO
PASSWORD
MENU SELECT
SUB MENU
2
FRONT-F
LOW
H
QUAD
OFF
LOGO1
ENTER
OPTION2
PROJECTOR ID
INSTALLATION
ALTITUDE
DIRECTION
LAMP SELECT
LAMP RELAY
RS-232C
SYSTEM INFORMATION
AIR FILTER CLEANING
DATE AND TIME
STARTUP LOGO
PASSWORD
MENU SELECT
SUB MENU
2
FRONT-F
LOW
H
QUAD
OFF
LOGO1
ENTER
RS-232C
SERIAL IN
(IN) BAUDRATE
(IN) PARITY
(OUT) BAUDRATE
(OUT) PARITY
VPS SYSTEM
GROUP
MENU SELECT
CHANGE
RS-232C
38400
EVEN
38400
EVEN
MASTER
A
MASTER
RS-232C
SERIAL IN
(IN) BAUDRATE
(IN) PARITY
(OUT) BAUDRATE
(OUT) PARITY
VPS SYSTEM
GROUP
MENU SELECT
CHANGE
RS-232C
38400
EVEN
38400
EVEN
MASTER
A
MASTER
- PT-D10000E 1
- PT-DW10000E 1
- Dear Panasonic Customer: 2
- Contents 3
- IMPORTANT SAFETY NOTICE 4
- 6 – ENGLISH 6
- 8 – ENGLISH 8
- Before Using 10
- Getting Started 11
- Notes on use 11
- Disposal 11
- 12 – ENGLISH 12
- Remote control unit 12
- 14 – ENGLISH 14
- Projector Main Unit 14
- 16 – ENGLISH 16
- Using the remote control unit 17
- 18 – ENGLISH 18
- Setting projector ID 18
- Using a wired remote 18
- Installation 19
- – ENGLISH 20
- (optional) 21
- 22 – ENGLISH 22
- 24 – ENGLISH 24
- Before starting connection 24
- 26 – ENGLISH 26
- Installing the input module 27
- 28 – ENGLISH 28
- 30 – ENGLISH 30
- 32 – ENGLISH 32
- ENGLISH – 33 33
- Projection 34
- Basic Operation 35
- Powering up the projector 35
- Making adjustment and 35
- 36 – ENGLISH 36
- Powering off the projector 36
- How to adjust the lens 37
- 38 – ENGLISH 38
- 40 – ENGLISH 40
- Registration of new data 40
- Clearing the data of 41
- Sub memory 41
- 42 – ENGLISH 42
- ENGLISH – 43 43
- Changing the picture 45
- On-screen menus 46
- 48 – ENGLISH 48
- Using the menu screens 48
- Resetting to the factory 48
- Adjusting the picture 49
- 50 – ENGLISH 50
- Adjusting Contrast 50
- Adjusting Brightness 50
- Adjusting Colour 50
- Adjusting Tint 51
- Adjusting the colour 51
- 52 – ENGLISH 52
- Gamma setting 52
- Sharpness setting 52
- Noise reduction setting 53
- Dynamic iris setting 53
- 54 – ENGLISH 54
- Registering the picture 54
- Setting the system format 54
- Adjusting the position 56
- Adjusting the aspect ratio 57
- 58 – ENGLISH 58
- Adjusting the zoom ratio 58
- Clock phase adjustment 58
- Keystone distortion 59
- How to use ADVANCED MENU 60
- Blanking adjustment 61
- 62 – ENGLISH 62
- Adjusting the clamp 62
- Edge blending adjustment 62
- 64 – ENGLISH 64
- Frame delay 64
- Raster position 65
- Setting the DISPLAY LANGUAGE 66
- Option1 settings 67
- 68 – ENGLISH 68
- Adjusting the colour 68
- Large Screen Correction 69
- 70 – ENGLISH 70
- Auto signal 70
- Automatic adjustment 70
- (Only RGB input) 70
- Back Colour 71
- DVI EDID 71
- 72 – ENGLISH 72
- AUX DVI EDID (Only when the 72
- Setting FUNC1 73
- 74 – ENGLISH 74
- Position of on-screen 74
- OSD memory 74
- Option2 settings 75
- 76 – ENGLISH 76
- Installation Setting 76
- Altitude 76
- Direction 77
- Output resolution 77
- (PT-D10000E only) 77
- 78 – ENGLISH 78
- Lamp select 78
- Lamp relay 79
- RS-232C setting 79
- 80 – ENGLISH 80
- System information 80
- Cleaning the air filter 80
- Setting the date and time 81
- 82 – ENGLISH 82
- Setting the startup logo 82
- Password 82
- Test pattern 83
- How to use network function 84
- 86 – ENGLISH 86
- Network connections 86
- 88 – ENGLISH 88
- 90 – ENGLISH 90
- 92 – ENGLISH 92
- 94 – ENGLISH 94
- 96 – ENGLISH 96
- Using the PJLink™ protocol 98
- Setting the security 99
- 100 – ENGLISH 100
- Changing the password 100
- Setting the text 100
- Special Features 101
- Changing the text 101
- Using the serial terminals 102
- 104 – ENGLISH 104
- Basic format 104
- Control commands 104
- Cable specifications 105
- Using the Remote 2 terminal 106
- Indication of monitor lamp 107
- 108 – ENGLISH 108
- Procedure of cleaning 108
- Information 109
- Replacement of lamp unit 110
- 112 – ENGLISH 112
- Installation procedure 112
- Self-diagnosis display 114
- 116 – ENGLISH 116
- BPR input] 117
- BPR: 0.7 V [p-p] 75 Ω 117
- Appendix 118
- List of P IN P 119
- Dimensions 120
- BPR/DVI-D Signals 121
- Trademark Acknowledgement 122
Related products and manuals for Projectors Panasonic PT-D10000E
Projectors Panasonic TX-47P950A User Manual
(39 pages)
(39 pages)
Projectors Panasonic PT-AX100E User Manual
(52 pages)
(52 pages)
Projectors Panasonic PT-LW80NTE User Manual
(58 pages)
(58 pages)
Projectors Panasonic PT 60LCX64 User Manual
(112 pages)
(112 pages)
Projectors Panasonic PT VX400NTU User Manual
(86 pages)
(86 pages)
Projectors Panasonic TQBJ0350 User Manual
(96 pages)
(96 pages)
Projectors Panasonic PT-AE500U User Manual
(30 pages)
(30 pages)
Projectors Panasonic TX-47P500X User Manual
(44 pages)
(44 pages)
Projectors Panasonic PT-AE700U User Manual
(32 pages)
(32 pages)
Projectors Panasonic PT-53WXD63 User Manual
(88 pages)
(88 pages)
Projectors Panasonic PT-60LC14 User Manual
(95 pages)
(95 pages)
Projectors Panasonic PT-DZ6710 User Manual
(52 pages)
(52 pages)
Projectors Panasonic PT-AE200 User Manual
(12 pages)
(12 pages)
© 2020, manymanuals.com. All rights reserved. | 1.371 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals