UB-T781Operating Instructions(For Basic Operations)Electronic Board(elite Panaboard)Model No. UB-T781UB-T781WUB-T761Installation Manual Included (for
Make sure that the battery is installedwith the correct polarity as indicated onthe battery holder. Incorrectly installedbatteries may burst or leak,
After installing or moving the unit, lockthe casters and set the fall-preventionextension legs.Locking the casters(Push this side)Push to lockOperatin
As the colours of the wire in the mains lead of thisapparatus may not correspond with the colouredmarkings identifying the terminals in your plug,proc
Warning Label䄺ਞ˖Ўњ䰆ℶ㾺⬉џᬙǃߛ࣓ᠧᓔᴎⲪDŽᴎ఼ݙ䚼≵᳝⫼᠋㞾Ꮕৃҹ㓈ׂⱘ䚼ߚDŽ㓈ׂџᅰࡵ䇋ྨᠬ᳝䌘Ḑⱘ㓈ׂҎਬDŽPBQAA0582ZAWARNING: TO PREVENT ELECTRIC SHOCK, DO NOT REMOVE COVER.NO USER-SERVICEA
Included AccessoriesCheck that all of the following items are included with your elite Panaboard.In the event that an item is missing, please contact
Names and Uses of the PartsScreenFront ViewPosition SensorDetects the position of the electronic pen. Do not block the sensor while operating the elit
Rear ViewAC InletPower CordNotice• The elite Panaboard is designed exclusively for projector images. Do not write on the screen boardwith a white-boar
Notice• Use the electronic pen by holding it at a right angle to the screen board.Holding it at an angle can cause its position to be read incorrectly
Connecting External Components1. Set the power switch to "O" (OFF), connect the power cord (included) to the elite Panaboard, andplug the po
2. Connect the elite Panaboard to a computer using the USB cable (included).• elite Panaboard: Plug the B connector (smaller connector) into the elite
IntroductionThank you for purchasing the Panasonic Electronic Board.For optimum performance and safety, please read these instructions carefully.Featu
Connecting External Devices1. Connect the external device to the elite Panaboard using a USB cable (sold separately).• elite Panaboard: Plug the A con
Volume Control• The volume of the USB speaker on the elite Panaboard can be controlled using the Volume Dial, the volumeof Windows, and the volume of
Installing the elitePanaboard softwareYou need to install the elite Panaboard software on thecomputer that will be used with the elite Panaboard.To in
Setting the ProjectorSet up your projector as instructed below.About Positioning the Image• When you are projecting an image, make sure thatthe edge o
• If the image is projected trapezoidally, theposition of the electronic pen may not be readcorrectly. Adjust the projector so that theprojected image
Starting the elitePanaboard software andPerforming Calibration1. Turn on the elite Panaboard.2. Connect the elite Panaboard to your computerwith the U
• After calibration has completed, the iconis displayed in the notification area, and theDesktop Drawing Tool is automaticallydisplayed.[Desktop Dra
Viewing the ElectronicDocumentationFollow the procedure below to view the electronicdocumentation "Operating Instructions (For Software)".1.
Daily CareWhen cleaning the elite Panaboard or inside the elite Panaboard, make sure to switch off the power and unplugthe power cord from the AC outl
Replacing the Penpoint of theElectronic PenAs the penpoint of the electronic pen becomes worn, ahole will appear in the penpoint. Continuing to use th
Things you should keep a record ofAttach your sales receipt hereFor your future referenceDate of purchaseSerial numberDealer’s nameDealer’s addressDea
TroubleshootingWhen experiencing problems, please refer to the table below for possible solutions. If the problem persists,contact your dealer.Symptom
Symptom Possible cause and solutionSeepageThe message "The penbattery is low. Replace thebattery soon." is displayedon the computer screen.T
SpecificationsModelNumberUB-T781 / UB-T781W / UB-T761General Power AC 100 V–240 V, 50 Hz/60 HzPower Consumption: DuringOperation0.4 AOperating Environ
ModelNumberUB-T781General External Dimensions: Height´ Width ´ Depth1,340 mm ´ 1,752 mm ´ 89 mm(4 ft. 4 3/4 in. ´ 5 ft. 9 in. ´ 3 1/2 in.)Weight 27 kg
ModelNumberUB-T781WGeneral External Dimensions: Height´ Width ´ Depth1,340 mm ´ 1,899 mm ´ 89 mm(4 ft. 4 3/4 in. ´ 6 ft. 2 3/4 in. ´ 3 1/2 in.)Weight
ModelNumberUB-T761General External Dimensions: Height´ Width ´ Depth1,142 mm ´ 1,489 mm ´ 89 mm(3 ft. 9 in. ´ 4 ft. 10 5/8 in. ´ 3 1/2 in.)Weight 21 k
Supplies & AccessoriesOptional Device Electronic Pen UE-608025Stand KX-B061*1Stand UE-608030Install-Free Kit UE-608050*1KX-B061 is not available f
Installation Manual (for qualified service personnel)• Request assembly of the Electronic Board, stand and wall mounting from your dealer.• Before con
Have the unit installed, removed anddisposed of only by qualified servicepersonnel.CAUTIONAfter installing or moving the electronicboard, lock the cas
Included AccessoriesConfirm that the following items are included with the elite Panaboard.No. Part Name Illustration Q’ty RemarksPower Cord(3 m [9 ft
AbbreviationsWindows® refers to the Microsoft® Windows® operating system.Windows® 2000 refers to the Microsoft® Windows® 2000 operating system.Windows
No. Part Name Illustration Q’ty RemarksWarranty 1May not be includeddepending on country/area.Notice• Screws (8 count) for wall mounting are not inclu
Wall Mounting ConstructionChecking the WallWhen mounting on a wall, consult with your building's owner, caretaker or construction manager to dete
Installing the Wall Mounting Plates1. Ensure that the wall is strong enough to support the elite Panaboard.Rated strength: greater than 1,373 N (140 k
UB-T76140 mm (1 9/16 in.)784 mm (2 ft. 6 7/8 in.)30 mm (1 3/16 in.)44 mm (1 23/32 in.)(1 ft. 9 21/32 in.)222.5 mm (8 3/4 in.)469.5 mm (1 ft. 6 1/2 in.
5. Mount the elite Panaboard on the wall.See "Assembling the elite Panaboard" (For Wall Mounting ® page 52).44 Operating Instructions (For B
Wall Types and Installation ProceduresThe method for attaching the wall mounting plates to the wall will vary depending on the wall's structure.T
Plasterboard wallsSplit-wing toggles (not included) are needed.PlasterboardSplit-wing toggleWall mountingplateBoltArmsArmsInsert the bolt through the
Stand Assembly (Sold Separately)Included PartsCheck that the following parts are included with the stand (KX-BP061).No.Part Name Illustration Q't
CAUTIONBefore assembly, be sure to lock the casters.Locking the casters(Push this side)Assembly Instructions1. Assemble the fall-prevention extension
2. Assemble the stand.REARFRONTAssemble with the holes toward the front.Locking casterside (rear)Locking caster side(rear)Notice• Do not over-tighten
Warning about saving dataWhen the system storage device or any of its optional storage device is adversely effected byoperational errors, static elect
3. Pull the fall-prevention extension legs down.21Note• When folding back the fall-prevention extension legs, release the lock as follows (1,2).1124.
Assembly InstructionsPreparing for Removing the elite Panaboard from Its PackagingOpen the box, remove the accessory box & packing foam and open t
Assembling the elite PanaboardFor Wall Mounting1. Loosely wrap the power cord with the cable tie,and plug the power cord into the AC inlet.• Connect t
4. Remove the screw (A) of the attachment cover(B), which is fixed to the attachment board, andslide the attachment cover down.Ensure that the attachm
8. Disconnect the 2 connectors from the audioboard (D).49. Fasten to the wall.Fasten the lower portion of the board attachmentsecurely to the wall.10.
12. Wipe the screen board surface.Gently wipe the screen board surface with a soft,moist cloth.Notice• Do not use thinner, benzene, or abrasivechemica
3. Hang the elite Panaboard on the stand with thescrew heads.4. Secure the elite Panaboard to the stand frameusing the two-wing bolts (M5 ´ 12 mm [1/2
Confirming the elite Panaboard OperationAfter assembling the elite Panaboard, confirm that it operates properly by following the procedure below.Actio
RepackagingTo repackage the elite Panaboard, perform steps in "Assembling the elite Panaboard" (For Wall Mounting ®page 52, For Mounting on
Attaching the Install-Free Kit (Sold Separately)Attaching the Install-Free Kit1. Unscrew the 4 screws from the front lowerframe cover.2. Lift the bott
Exemption of LiabilityPanasonic Communications Co., Ltd. is not responsible for accidents or injuries caused by, but not limited to,the following:1. A
5. Disconnect the black cable and the white cablefrom the clamper (B).26. Unscrew the 7 screws and remove the hub PCBshield plate.7. Attach the instal
Operating Instructions (For Basic Operations) 611Notes
62 Operating Instructions (For Basic Operations)Notes
Operating Instructions (For Basic Operations) 631Notes
© Panasonic Communications Co., Ltd. 2009Information for Users on Collection and Disposal of Old Equipment and used BatteriesThese symbols on the prod
Table of ContentsFor Your Safety ...8For Your Safety ...
For Your SafetyTo prevent severe injury and loss of life, read thissection carefully before using the unit to ensure properand safe operation of your
Plug the power cord firmly into an ACoutlet. Otherwise, it can cause fire orelectric shock.Do not pull, bend, rest objects on, orchafe the power cord
Comments to this Manuals