Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number i
10PrecautionsRefer installation work to the dealer.Installation work requires technique and experi-ences. Failure to observe this may cause fire, elec
11Keep SDXC/SDHC/SD memory cards (option) away from infants and children. Otherwise, they may swallow the cards by mis-take. In this case, consult a d
12card will be deleted when formatted. If an unfor-matted SD memory card or an SD memory card formatted with other devices is used, this product may n
13Precautions for installationThis product is designed to be installed under eaves.Install the product under eaves to avoid direct sunlight.Installing
14Do not remove or loosen the internal cam-era screwsDo not loosen the internal camera screws. Otherwise, water exposure may cause damage or malfuncti
15About the initial set buttonAfter turning off the power of the camera, turn on the power of the camera while holding down this button, and wait for
16IMPORTANT: • Remove the cover film attached to the dome cover after the camera installation is completed. After removing the cover film, do not tou
17When installing the camera on a ceiling or a wall, there are three methods as specified below. • Directly mounting to a ceiling or a wall • Use
18Method of camera installationInstalling the camera directly on the ceiling or wallNote: • Use the installation template label (accessory) with the
19Using the mount bracket (accessory)Note: • When the camera is mounted on the ceiling or wall with a hole for cable running and the cables are pass
2The model number and serial number of this product may be found on the surface of the unit.You should note the model number and serial number of this
20<Connecting the cable through holes opened in the ceiling or wall>Place the installation template label (accessory) on the ceiling or wall, ma
21Using a one-gang junction box • Secure the mount bracket (accessory) to the one-gang junction box built in a ceiling or a wall.Note: • Ceiling ins
22IMPORTANT: • When inserting an SD memory card, make sure the direction. • Before removing the SD memory card, select "Not use" for &quo
23Caution: • FOR UL LISTED MODEL(S), ONLY CONNECT PoE 48 V CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/UL/CSA 60950-1).Bef
24Waterproof treatment for the cable joint sectionsAdequate waterproof treatment is required for the cables when installing the camera outdoors. The c
25Connection example<Required cable>LAN cable (category 5 or better, straight)IMPORTANT: • Use a switching hub which is compliant with 10BASE
26Camera mounting<Installing the camera directly on the ceiling or wall> Remove the enclosure. (3 screws) ( Page 16) Connect the cables to th
27<Using a one-gang junction box> Connect each cable. • Apply waterproof treatment to all connections. ( Page 24) Secure the mount bracke
28Using the side cable access hole When installing the camera directly on the ceiling or wall with cables exposed, cut off a portion of the mount bra
29 Adjust the camera angle.When determining the camera angle, repeat fine adjustments by gradually moving the panning table and tilting table. • At
3ContentsImportant safety instructions ... 4Limi
30Note: • Depending on the vertical/horizontal angle used, the edges of the camera may be projected. • Use Extra Zoom when you want to adjust the
31 Attach the enclosure to the camera by using the tamperproof screw bit (accessory) to tighten the 3 enclosure fixing screws (M3). (Recommended tigh
32Configuring the camera so that it can be accessed from a PCThe following are descriptions for when the camera with default settings is configured. I
33 If the installation screen of the viewer software “Network Camera View 4S” is displayed, follow the instructions of the wizard to start the instal
34Before asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after checking and tr
35• BasicPower source: PoE (IEEE802.3af compliant)Power consumption: PoE 48 V: 110 mA/5.3 W(Class 2 device)Ambient operating temperature: -30 °C to
36Camera title on screen: Up to 20 characters (alphanumeric characters, marks) On/OffVideo motion detection (VMD alarm): On/Off, 4 areas availabl
37Image compression method*1: Frame rate: 1fps/ 3fps/ 5fps/ 7.5fps/ 10fps/ 12fps*/ 15fps/ 20fps/ 30fps * E model only JPEG (MJPEG) Ima
38OS*3 *4: Microsoft® Windows® 8 Microsoft® Windows® 7 Microsoft® Windows Vista® Microsoft® Windows® XP SP3Browser: Windows® Internet Explorer®
39Installation Guide (this document) ...2 pcs.Important Safety Instructions ...
4Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do
40For U.S. and Canada:Panasonic System Communications Company of North America,Unit of Panasonic Corporation of North Americawww.panasonic.com/busin
5Limitation of liabilityTHIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMI
6The network camera WV-SW158 is designed to operate using a PC on a network (10BASE-T/100BASE-TX), and can be installed under eaves (sheltered outdoor
7System requirements for a PCAbout the user manualsThere are 2 sets of operating instructions for the WV-SW158 as follows. • Installation Guide: Ex
8IMPORTANT: • When using a PC that does not meet the above requirements, displaying of images may become slower or the web browser may become inopera
9Network securityAs you will use this unit connected to a network, your attention is called to the following security risks. q Leakage or theft of i
Comments to this Manuals