Panasonic SC-HC35 User Manual download pdf (Page 15)

RQTX1260

ENGLISH

1 Press [ , iPod] repeatedly to select

“BLUETOOTH”.

2 Press [ MENU] to display “DISCONNECT?”

and then press [OK].

A confirmation message is displayed.

3 Press [2, 1] to select “YES” and then press

[OK].



≥ The connection can also be stopped when you disable Bluetooth

transmission on the connected Bluetooth

device.

Preparation

Press [ , iPod] repeatedly to select “BLUETOOTH”.

≥ These functions are unavailable if a device is connected. Disconnect the

Bluetooth

devices to display these functions.

∫ To register more devices

1 Press [ MENU] repeatedly to select

“NEW DEV.” and then press [OK].

≥ The unit enters pairing mode and “PAIRING” starts blinking

on the display.

2 While this unit is in pairing mode, access the

Bluetooth

menu of the Bluetooth

device and

execute a Bluetooth

search to find this unit

(SC-HC55).

≥ If prompted for the passkey, enter “0000”.

∫ To select communication quality

1 Press [ MENU] repeatedly to select

“LINK MODE”.

2 Press [2, 1] to select the following modes and

then press [OK].

∫ To select Auto Link mode

1 Press [ MENU] repeatedly to select

“AUTO LINK”.

2 Press [2, 1] to select the following modes and

then press [OK].



≥ When “LINKING” is displayed, pressing [ MENU] is invalid.

≥ Auto Link works only if your device supports A2DP.

≥ The communication quality settings also depend on the settings on the

connected device. If the communication quality of the connected device is set

for stable communication, the quality of the audio will remain low even if this

unit is set to “MODE 2”.

Others

Other Panasonic audio/video equipment may start functioning

when you operate the unit using the supplied remote control.

You can operate this unit in another mode by setting the remote

control operating mode to “REMOTE 2”.

The main unit and remote control must be set to the same

mode.

1 Press [EXT-IN, RADIO] to select “AUX”.

2 Press and hold [RADIO/EXT-IN] on the main

unit and [2] on the remote control until the main

unit’s display shows “REMOTE 2”.

3 Press and hold [OK] and [2] on the remote

control for at least 4 seconds.

To change the mode back to “REMOTE 1”, repeat the steps

above by replacing [2] with [1].

When the following situations occur, reset the memory:

≥ There is no response when buttons are pressed.

≥ You want to clear and reset the memory contents.

∫ To reset memory

1 Disconnect the AC power supply cord. (Wait for

at least 3 minutes before proceeding to step 2.)

2 While pressing and holding down [POWER, Í/

I] on the main unit, reconnect the AC power

supply cord.

“--------” appears on the display.

3 Release [POWER, Í/I].

All the settings are returned to the factory preset. You will

need to reset the memory items.

Disconnecting a Bluetooth

device

Advanced functions

MODE 1: Connection with emphasis on communication

stability

MODE 2: Connection with high bit rate for good audio quality

(Communication might easily be disconnected in

this mode, select “MODE 1” if this occurs).

ON: This unit will automatically select “BLUETOOTH”

when a Bluetooth

device is connected.

OFF

Changing the main unit and

remote control mode

Memory reset (Initialization)

SC-HC55_35-RQTX1260.book 15 ページ２０１１年４月４日　月曜日　午後４時５０分

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 27 28

Comments to this Manuals

No comments

Panasonic SC-HC35 User Manual Page 15

Comments to this Manuals

Related products and manuals for Acoustics Panasonic SC-HC35