Panasonic DMP-BDT330 Owner's Manual download pdf (Page 36)

36

VQT4V26

This unit does not recognize the USB

connection correctly.

¾ Disconnect and reconnect the USB cable. If it

still does not recognize the connection, turn

this unit off and on again.

¾ USB devices may not be recognized by this

unit when connected using the following :

– a USB hub

– a USB extension cable

¾ If you connect USB HDD to this unit, use the

USB cable that is supplied with the HDD.

The images from this unit do not appear on

the TV.

Picture is distorted.

¾ An incorrect resolution is selected in “HDMI

Resolution”. Reset the setting as follows:

1 Turn the unit on.

2 Press and hold [OK], the blue button and the

yellow button on the remote control at the

same time for more than 5 seconds.

– “00RET” is displayed on the unit’s display.

3 Press [1] (right) repeatedly on the remote

control until “04PRG” is displayed on the

unit’s display.

4 Press and hold [OK] for more than 5 seconds.

Set the item again. (> 29)

– When Dolby Digital Plus, Dolby TrueHD,

and DTS-HD audio are not output properly,

select “Yes” in “Restore Default Settings”

and make proper settings. (> 34)

¾ When “3D BD-Video Playback” in the Setup

menu is set to “Auto”, images may not be

output depending on the connection method.

After removing the disc from this unit, select

“Set before play” in the Setup menu, and

select “2D Playback” in the setup screen

displayed when playing 3D discs. (> 31)

¾ [BDT330] : When outputting in 24p (4K),

images may be distorted depending on the

HDMI cable. Use an HDMI cable that

supports 4K output.

Video is not output. [BDT330]

¾ Video from the HDMI AV OUT SUB terminal is

not output when the “HDMI(SUB) Output

Mode” is set to “V.OFF”. (> 30)

Video is not output in high-definition.

¾ Confirm that “HDMI Resolution” in the Setup

menu is set properly. (> 29)

3D video is not output.

¾ Connect to a full high-definition TV.

¾ Is there a non-3D compatible amplifier/

receiver connected between this unit and a

TV? (> 11)

¾ [BDT330] : If there is a non-3D compatible

amplifier/receiver connected to the HDMI AV

OUT SUB terminal, set the “HDMI(SUB)

Output Mode” to “V.OFF”. (> 11)

¾ Are the settings on this unit and the TV

correct? (> 21)

¾ Is the amplifier/receiver that is connected

between this unit and TV on?

¾ Depending on the connected TV, the video

being played back might switch to 2D video

due to changes in resolution etc. Check the

3D setting on the TV.

3D video is not output correctly as 2D.

¾ Select “Set before play” in the Setup menu,

and select “2D Playback” in the setup screen

displayed when playing 3D discs. (> 31, “3D

BD-Video Playback”)

¾ Discs that have recorded titles with Side by

side (2 screen structure) and that can be

enjoyed in 3D are played back in accordance

with the settings of the TV.

No subtitles.

¾ When progressive output is on, closed

captions/subtitles cannot be displayed.

The subtitles overlap closed captions

recorded on discs.

¾ Turn off the subtitles or the closed caption

setting on the TV. (> 27)

A black band is displayed around the edge of

the screen.

The aspect ratio of the screen is abnormal.

¾ Confirm the “TV Aspect” is set properly.

(> 33)

¾ Adjust the aspect setting on the TV.

Picture

DMP-BDT330_230_VQT4V26_eng.book 36 ページ２０１２年１２月２７日　木曜日　午前１１時１３分

1 ... 35 36 37 ... 48

Comments to this Manuals

No comments