Panasonic KX-TD500 User Manual

Please read this manual before connecting the Digital Super Hybrid System and save this manual for future reference.Thank you for purchasing the Panas

Configuration10 Programming GuideParameter StatusDefault —Value Range1. INS2. OUS3. FAULTDescription/Function Used to set the status of the service ca

System100 Programming Guide2.8.3 System Option 3Used to assign system option parameters (No.21 — No.30).Parameter 20. Off-hook MonitorDefault EnableVa

SystemProgramming Guide 101Message Waiting lamp patterns (1/2)The available message waiting lamp patterns are as follows:(s)ONOFFPattern #01Pattern #0

System102 Programming GuideMessage Waiting lamp patterns (2/2)(s)ONOFFPattern #07Pattern #08Pattern #09Pattern #10Pattern #11Pattern #12(s)ONOFF(s)ONO

SystemProgramming Guide 103Parameter 21. Illegal Number - DISADefault Send reorder toneValue Range1. Send reorder tone2. Transferred to IRNA destinati

System104 Programming GuideParameter 25. Pressing DSS key operation in CO talkingDefault HoldValue Range1. Disconnect2. HoldDescription/Function If se

SystemProgramming Guide 105Parameter 28. Trunk hunting modeDefault ForcedValue Range1. Forced2. Loop DetectionDescription/Function Specifies the trunk

System106 Programming Guide2.8.4 System Option 4Used to assign system option parameters (No.31 – No.49).Parameter 31. Answering Call Waiting call by S

SystemProgramming Guide 107Parameter 33. FWD / DND lamp patternDefault FWD: Flash, DND: OnValue Range1. FWD: Flash, DND: On2. FWD: On, DND: FlashDescr

System108 Programming GuideParameter 36. Tone ModeDefault Type-3: [SA], Type-4: [HK], Type-1: OthersValue Range1. Type-12. Type-23. Type-34. Type-45.

SystemProgramming Guide 109Parameter 39. Extension CPC SignalDefault NoneValue Range None, 16-240 ms in 16 ms incrementsDescription/Function Specifies

ConfigurationProgramming Guide 111.3 Trunk Port AssignmentUsed to assign each trunk port in the system to one of up to 48 trunk groups.Parameter Card

System110 Programming GuideParameter 43. LCD Time Display ModeDefault 12hValue Range1. 12h2. 24hDescription/Function Specifies the time display on the

SystemProgramming Guide 111Parameter 47. Tone Type for Outgoing CallsDefault Busy + ReorderValue Range1. Busy + Reorder2. Busy3. ReorderDescription/Fu

System112 Programming Guide2.8.5 System Option 5Used to assign System Option parameters (No. 50 - No. 60).Parameter 50. Dial / Ringback tone frequency

SystemProgramming Guide 113Parameter 51. Release of BRI/PRI line while on-hold when'DISCONNECT' signal is receivedDefault ReleaseValue Range

System114 Programming GuideParameter 53. TIE-CO/CO-TIE Line Call Duration RestrictionDefault NoValue Range1. Yes2. NoDescription/Function This paramet

SystemProgramming Guide 115Parameter 55. Displaying charge fee on LCD including marginDefault NoValue Range1. Yes2. NoDescription/Function Switches th

System116 Programming GuideParameter 58. Release of BRI/PRI line while talking when'DISCONNECT' signal is receivedDefault Release: [HK], Don

SystemProgramming Guide 1172.8.6 System Option 6Used to assign system option parameters (No.61 – No.65).Parameter 61. Auto Answer with held callDefaul

System118 Programming GuideParameter 63. Tenant Select Mode for DID / DDIDefault Trunk GroupValue Range1. Trunk Group2. DID / DDI No.Description/Funct

SystemProgramming Guide 1192.9 Language DataDisplay LanguageThe KX-TD500 System provides two different languages as the Display Language at the sameti

Configuration12 Programming GuideParameter StatusDefault —Value Range1. INS2. OUS3. FAULTDescription/Function Specifies the operating status of the tr

System120 Programming Guidecan upload the Language Data in the same way as described in <Uploading theLanguage Data to the KX-TD500 System>.

GroupProgramming Guide 121Section 3Group

Group122 Programming Guide3.1 GroupUsed to assign various group parameters.

GroupProgramming Guide 1233.2 Trunk Group3.2.1 Trunk Group 1/2Used to assign parameters for each trunk group.Up to 48 trunk groups can be created in t

Group124 Programming GuideTrunk Group CopyUsed to copy a part of or all settings of a certain Trunk Group to all other Trunk Groups at atime. You can

GroupProgramming Guide 125Parameter Group No.Default 1Value Range 1-48Description/Function Specifies the trunk group (1-48) which you are going toprog

Group126 Programming GuideParameter Intercept Destination – Day / NightDefault BlankValue Range 3-4 digits consisting of 0-9Description/Function Speci

GroupProgramming Guide 127Parameter Line Hunting OrderDefault NormalValue Range1. Normal2. Reverse3. SequentialDescription/Function Specifies the hunt

Group128 Programming GuideParameter Flash TimeDefault 80 ms: [SA], 600 ms: OthersValue Range1. None2. 80 ms3. 300 ms4. 600 ms5. 900 ms6. 1200 msDescri

GroupProgramming Guide 129Parameter Pause TimeDefault 1.5 sValue Range1. 1.5 s2. 2.5 s3. 3.5 s4. 4.5 sDescription/Function Specifies the length of pau

ConfigurationProgramming Guide 131.4 Extension Port AssignmentUsed to set various parameters for extension ports.XDP extensions are on ports 9 through

Group130 Programming GuideParameter [Numbering Plan ID] Outgoing—PrivateDefault PrivateValue Range1. Default2. Unknown3. ISDN / Telephony4. National S

GroupProgramming Guide 131Parameter PBX Dial ToneDefault DisableValue Range1. Enable2. DisableDescription/Function If enabled, the system sends a dial

Group132 Programming GuideParameter [Type of Number] Outgoing—PublicDefault DefaultValue Range1. Default2. Unknown3. International4. National5. Networ

GroupProgramming Guide 133Parameter [Type of Number] Incoming—PrivateDefault DefaultValue Range1. Default2. Unknown3. International4. National5. Netwo

Group134 Programming Guide3.2.2 Trunk Group 2/2Used to assign parameters for each trunk group. Up to 48 trunk groups can be created in thesystem.Param

GroupProgramming Guide 135Parameter ISDN Progress Tone ModeDefault AutomaticValue Range1. Automatic2. Network3. PBXDescription/Function Selects the wa

Group136 Programming Guide3.3 Extension GroupUsed to assign various parameters for up to 128 (1-128) Extension Groups.Which parameters apply to your E

GroupProgramming Guide 137( = assignable)Applicability of Parameters to Group TypesGroup TypeParameter None Ter. Cir. Ring Ope. VM AA UCDGroup No.FDNT

Group138 Programming Guide( = assignable)*1When "DIL 1:N" is specified in "Group Type" programming of Incoming Group, this feature

GroupProgramming Guide 139Extension Group CopyUsed to copy a part of or all settings of a certain Extension Group to all other Extension Groupsat a ti

Configuration14 Programming GuideParameter AttributeDefault TELValue Range1. TEL2. DSS3. VPS (DPT)4. PC ConsoleDescription/Function Specifies the attr

Group140 Programming GuideParameter Group No.Default 1Value Range 1-128Description/Function Specifies the Extension Group (1-128) which you are going

GroupProgramming Guide 141Parameter Tenant No.Default 1Value Range 1-8Description/Function Specifies the tenant (1-8) to which the Extension Group is

Group142 Programming GuideParameter Group TypeDefault Group No.126: VM, Group No.127: AA, Group No.128: Operator,Others: NoneValue Range1. None2. Term

GroupProgramming Guide 143Parameter FWD / DND ModeDefault EnableValue Range1. Disable2. EnableDescription/Function Specifies whether to enable or disa

Group144 Programming GuideParameter Calls to Empty GroupDefault DisableValue Range1. Enable2. DisableDescription/Function Allows for calls to empty (a

GroupProgramming Guide 145Parameter [UCD Setting] FWD No AnswerDefault DisableValue Range1. Disable2. EnableDescription/Function Specifies the treatme

Group146 Programming GuideParameter [UCD Setting] Supervisor ExtensionDefault BlankValue Range 3-4 digits consisting of 0-9Description/Function Specif

GroupProgramming Guide 147Parameter [UCD Setting] UCD Call WaitingDefault EnableValue Range1. Disable2. EnableDescription/Function This feature is dif

Group148 Programming GuideParameter [Operator Setting] Ringing TypeDefault SingleValue Range1. Multi2. SingleDescription/Function Specifies whether th

GroupProgramming Guide 1493.4 Paging GroupUsed to programme up to 16 Paging Groups. Each Paging Group consists of up to 24 ExtensionGroups. One Extens

ConfigurationProgramming Guide 15Parameter Te l. TypeDefault (Display only)Value Range Please refer to "Description / Function."Description/

Group150 Programming Guide3.5 Incoming GroupUsed to programme a list of up to 96 Incoming Groups.Which parameters apply to your Incoming Group?Please

GroupProgramming Guide 151( = assignable)Applicability of Parameters to Group TypesParameterGroup TypeDIL1:NTer. Ring Ope. UCD[Overflow Setting]Destin

Group152 Programming Guide( = assignable)*1When "DIL 1:N" is specified in "Group Type" programming of Incoming Group, this feature

GroupProgramming Guide 1533. Select the Incoming Group parameters to copy in "Copy Item" field.• Only parameters which are available to copy

Group154 Programming GuideParameter DN ReferDefault —Value Range —Description/Function Displays the list of DNs/FDNs which are already assigned to the

GroupProgramming Guide 155Parameter [Overflow Setting] Destination – Day / NightDefault BlankValue Range 3-4 digits consisting of 0-9Description/Funct

Group156 Programming GuideParameter Mailbox No.Default BlankValue Range 3-4 digits consisting of 0-9Description/Function Specifies the mailbox number

GroupProgramming Guide 157Parameter Search ModeDefault UCDValue Range1. UCD2. SequentialDescription/Function Specifies the search mode for extensions.

Group158 Programming GuideParameter [UCD Setting] Time Table No.Default NoneValue Range None, 1-32Description/Function Specifies the UCD Time Table (1

GroupProgramming Guide 159Parameter [UCD Setting] Supervisor ExtensionDefault BlankValue Range 3-4 digits consisting of 0-9Description/Function Specif

Configuration16 Programming GuideParameter Card TypeDescription/Function Notes• Some telephones in the above list are not availabledepending on the de

Group160 Programming GuideParameter [Operator Setting] Call PriorityDefault CO Call:1, Intercept Routing:2, Recall:3, Extension Call:4Value Range Prio

GroupProgramming Guide 1613.5.1 Destination for Incoming GroupYou can assign up to 72 extensions and/or Extension Groups per Incoming Group so that an

Group162 Programming GuideParameter [Destinations] Ringing TypeDefault ImmediateValue Range1. Immediate2. 1-ring Delay3. 3-ring Delay4. 6-ring Delay5.

GroupProgramming Guide 1633.6 OGM GroupUsed to assign parameters for OGM Groups (1-8).OGM resources on the DISA card can be grouped together as an OGM

Group164 Programming GuideParameter DN ReferDefault —Value Range —Description/Function Displays the list of DNs/FDNs which are already assigned to the

GroupProgramming Guide 165Parameter Security ModeDefault TrunkValue Range1. None2. Trunk3. AllDescription/Function Specifies the Security Mode for DIS

Group166 Programming Guide

LineProgramming Guide 167Section 4Line

Line168 Programming Guide4.1 LineUsed to assign various parameters for both trunk and extension lines.

LineProgramming Guide 1694.2 Trunk LineUsed to assign various parameters for trunk lines.

ConfigurationProgramming Guide 17Parameter Parallel / XDP (DHLC card)Default ParallelValue Range 1. Parallel2. XDPDescription/Function Specifies wheth

Line170 Programming GuideTrunk Line CopyUsed to copy a part of or all settings of a certain Trunk Line to all other same type Trunk Linesat a time. Yo

LineProgramming Guide 171Parameter Card No.Default —Value Range XXX : YYY [XXX : Card No. (101-314), YYY : Card Type]Description/Function Specifies th

Line172 Programming GuideParameter NameDefault CO001-CO192Value Range Up to 10 characters consisting of 0-9, A-Z, a-z or the followingmarks:!#$% ()+,-

LineProgramming Guide 173Parameter Incoming TypeDescription/Function <Available selections and the default values per Card Type><Default valu

Line174 Programming GuideParameter Dial TypeDefault Pulse-10: [SA], DTMF-80: Others (DID-2W/E1/E&M/ELCOT/GCOT/LCOT/PCOT/RCOT/T1 card), ISDN (BRI/P

LineProgramming Guide 175Parameter Destination – Day / Night / Lunch / BreakDefault Day, Night: 1001, Lunch, Break: BlankValue Range 3-4 digits consis

Line176 Programming GuideParameter [DDI / DID / TIE] Digits to deleteDefault 0Value Range 0-16 digitsDescription/Function Specifies the number of digi

LineProgramming Guide 177Parameter Collect CallDefault EnableValue Range1. Enable2. DisableDescription/Function Specifies whether to enable or disable

Line178 Programming GuideParameter Start Signal TypeDefault WinkValue Range1. Immediate2. WinkDescription/Function Specifies the start signal type for

LineProgramming Guide 179Parameter [CPC Signal] OUT DetectionDefault Enable: DID / DID-2W / DID-MFC / E1 [DR2] card, Disable:ELCOT / GCOT / LCOT / PCO

Configuration18 Programming GuideParameter DN ReferDefault —Value Range —Description/Function Displays the list of DNs/FDNs which are already assigned

Line180 Programming GuideParameter [CPC Signal] IN DetectionDefault [NZ]: Enable, Others (Enable: DID / DID-2W / DID-MFC / E1[DR2] card, Disable: ELCO

LineProgramming Guide 181Parameter [TIE Line] TypeDefault 4wiresValue Range1. 2wires2. 4wiresDescription/Function Specifies the voice path type of TIE

Line182 Programming GuideParameter [TIE Line] Sensitivity - OUT CODefault 0dBValue Range - 3 to +6 dB in 3 dB incrementsDescription/Function Specifies

LineProgramming Guide 183Parameter Reverse Signal DetectionDefault Enable: [NZ], Disable: OthersValue Range1. Enable2. DisableDescription/Function If

Line184 Programming Guide4.3 Extension Line4.3.1 Extension Line 1/2Used to assign parameters for extension lines.

LineProgramming Guide 185Extension Line CopyUsed to copy a part of or all settings of a certain Extension Line to all other Extension Lines ata time.

Line186 Programming GuideParameter Card No.Default —Value Range XXX : YYY [XXX : Card No. (101-314), YYY : Card Type]Description/Function Specifies th

LineProgramming Guide 187Parameter CopyDefault —Value Range —Description/Function You can enter into "Extension Line Copy" screen by clickin

Line188 Programming GuideParameter Mailbox No.Default Same as the extension numberValue RangeUp to 16 digits consisting of 0 - 9, , # or P [Pause]Desc

LineProgramming Guide 189Parameter Charge LimitDefault 0Value Range 0: No limit1-99999: The number of charge metre allowable for the extensionDescript

ConfigurationProgramming Guide 191.5 VPS (DPT) Port AssignmentUsed to assign parameters for VPS (DPT) ports. Up to eight Panasonic Voice ProcessingSys

Line190 Programming GuideParameter [Preferred Line] OutgoingDefault Prime Line - ICM/PDNValue Range1. No Line2. Idle Line3. Prime Line - ICM / PDN4. P

LineProgramming Guide 191Parameter [Preferred Line] Incoming - Key No.Default BlankValue Range 1-24Description/Function Specifies the CO button to whi

Line192 Programming GuideParameter [LCS Setting] StatusDefault InactiveValue Range1. Inactive2. ActiveDescription/Function Specifies whether or not th

LineProgramming Guide 193Parameter Data Line ModeDefault NoValue Range1. Yes2. NoDescription/Function Assigns whether "Data Line Security mode&qu

Line194 Programming GuideParameter LanguageDefault EnglishValue Range1. English2. OptionDescription/Function Specifies the language shown on a PANASON

LineProgramming Guide 195Parameter ISDN Bearer ModeDefault AutomaticValue Range1. Automatic2. Speech3. 3.1 KHz AudioDescription/Function Specifies the

Line196 Programming GuideParameter [CLIP / COLP Number] PublicDefault BlankValue RangeUp to 16 digits consisting of 0 - 9, or #Description/Function Sp

LineProgramming Guide 197Parameter [CLIP / COLP Number] PrivateDefault BlankValue RangeUp to 16 digits consisting of 0 - 9, or #Description/Function S

Line198 Programming Guide4.3.2 Flexible CO Key AssignmentUsed to determine the usage of flexible CO buttons on PTs.The following screen is displayed b

LineProgramming Guide 199<Key Type Assignment>The following Key Type Assignment screen is displayed by clicking "Key Type Display"butt

Introduction2 Programming GuideIntroductionThis Programming Guide is designed to serve as a technical reference for the Panasonic DigitalSuper Hybrid

Configuration20 Programming GuideSave the data changes by clicking "Apply" button.Then set "Port Status" to "INS (In-Service)

Line200 Programming GuideSDN EXT. Specifies the PDN owner's extension number (3 or 4 digits).Tone (2) Specifies the ringer frequency (ring tone t

LineProgramming Guide 201Parameter Key TypeDefault CO-01: Loop-CO, Others: Not StoredValue Range Please refer to "Description / Function."De

Line202 Programming Guide4.3.3 Flexible PF Key Assignment for PTUsed to determine the usage of flexible PF buttons on PTs.The following screen is disp

LineProgramming Guide 203<Additional Parameters Required by Key Type>Depending on a Key Type, additional parameters are required as follows.Key

Line204 Programming Guide4.3.4 Extension Line 2/2Used to assign parameters for extension lines.Parameter Intercept Destination – Day / NightDefault Bl

LineProgramming Guide 205Parameter Call Forwarding-No Answer TimeDefault 0ringValue Range 0-12 ringsDescription/Function Specifies the number of rings

Line206 Programming Guide4.4 DSS ConsoleUsed to assign the paired extension for a DSS (Direct Station Selection) Console and the usageof DSS and PF bu

LineProgramming Guide 207DSS Console CopyUsed to copy a part of or all settings of a certain DSS Console to all other DSS Consoles at atime. You can a

Line208 Programming GuideParameter Paired ExtensionDefault (Display only)Value Range 3-4 digits consisting of 0-9Description/Function Displays the ext

LineProgramming Guide 2094.4.1 Flexible DSS Key AssignmentUsed to determine the usage of flexible DSS buttons on DSS Consoles.The following screen is

ConfigurationProgramming Guide 21Parameter TypeDefault NoneValue Range1. None2. TVP753. TVP1004. TVP2005. TVP200-16. TVP300Description/Function Specif

Line210 Programming Guide<Key Type Assignment>The following Key Type Assignment screen is displayed by clicking "Key Type Display"butt

LineProgramming Guide 211Parameter Key TypeDefault Not StoredValue Range Please refer to "Description / Function."Description/Function Not S

Line212 Programming Guide4.4.2 Flexible PF Key Assignment for DSS ConsoleUsed to determine the usage of flexible PF buttons on DSS Consoles.The follow

LineProgramming Guide 213<Additional Parameters Required by Key Type>Depending on a Key Type, additional parameters are required as follows.Key

Line214 Programming Guide4.5 DoorphoneUsed to assign the destination extensions for incoming calls from doorphones.Note• The DPH/DPHG card is not avai

LineProgramming Guide 215Parameter Tenant No.Default 1Value Range 1-8Description/Function Specifies the tenant (1-8) to which the doorphone port is as

Line216 Programming Guide4.6 External PagingUsed to assign parameters for External Paging.Parameter Pager No.Default (Display only)Value Range 1, 2Des

LineProgramming Guide 217Parameter FDNDefault BlankValue Range 3-4 digits consisting of 0-9Description/Function Specifies the FDN (Floating Directory

Line218 Programming GuideParameter DN ReferDefault —Value Range —Description/Function Displays the list of DNs/FDNs which are already assigned to thee

LineProgramming Guide 2194.7 ISDN Extension LineUsed to assign parameters for ISDN extension lines.Parameter Card No.Default —Value Range XXX: BRI [XX

Configuration22 Programming GuideParameter [Ext No.1] DNDefault BlankValue Range 3-4 digits consisting of 0-9Description/Function Specifies the extens

Line220 Programming GuideParameter Group No.Default (Display only)Value Range 1-128Description/Function Displays the Extension Group to which the sele

LineProgramming Guide 221Parameter ISDN Bearer ModeDefault AutomaticValue Range1. Automatic2. Speech3. 3.1 KHz AudioDescription/Function Specifies the

Line222 Programming GuideParameter [CLIP / COLP Number] PublicDefault BlankValue RangeUp to 16 digits consisting of 0-9, or #Description/Function Spec

LineProgramming Guide 223Parameter [CLIP / COLP Number] PrivateDefault BlankValue RangeUp to 16 digits consisting of 0-9, or #Description/Function Spe

Line224 Programming GuideParameter [COS No.] SecondaryDefault 1Value Range 1-96Description/Function Specifies the Secondary COS (Class of Service) (1-

LineProgramming Guide 2254.8 PC Console Line4.8.1 PC Console Line 1/2Used to assign parameters for PC Console lines.Parameter Card No.Default —Value R

Line226 Programming GuideParameter DNDefault —Value Range 3-4 digits consisting of 0-9Description/Function Specifies the PC Console which you are goin

LineProgramming Guide 227Parameter Mailbox No.Default Same as the extension numberValue RangeUp to 16 digits consisting of 0-9, , # or P [Pause].Descr

Line228 Programming GuideParameter [VM Key] 2WAY-TRNDefault BlankValue Range 3-4 digits consisting of 0-9Description/Function Specifies the Directory

LineProgramming Guide 229Parameter [COS No.] PrimaryDefault 1Value Range 1-96Description/Function Specifies the Primary COS (Class of Service) to the

ConfigurationProgramming Guide 23Parameter [Ext No.2] DNDefault BlankValue Range 3-4 digits consisting of 0-9Description/Function Specifies the extens

Line230 Programming GuideParameter [Preferred Line] Outgoing – Key No.Default BlankValue Range 1-24Description/Function Specifies the CO button to whi

LineProgramming Guide 231Parameter [Pickup Dialing] ModeDefault DisableValue Range1. Enable2. DisableDescription/Function Specifies whether "Pick

Line232 Programming GuideParameter [LCS Setting] Operation ModeDefault Hands-freeValue Range1. Private2. Hands-freeDescription/Function Assigns whethe

LineProgramming Guide 233Parameter Data Line ModeDefault NoValue Range1. Yes2. NoDescription/Function Assigns whether "Data Line Security mode&qu

Line234 Programming GuideParameter LanguageDefault EnglishValue Range1. English2. OptionDescription/Function Specifies the language shown on a PANASON

LineProgramming Guide 235Parameter ISDN Bearer ModeDefault AutomaticValue Range1. Automatic2. Speech3. 3.1 KHz AudioDescription/Function Specifies the

Line236 Programming GuideParameter [CLIP / COLP Number] PublicDefault BlankValue RangeUp to 16 digits consisting of 0-9, or #Description/Function Spec

LineProgramming Guide 237Parameter [CLIP / COLP Number] PrivateDefault BlankValue RangeUp to 16 digits consisting of 0-9, or #Description/Function Spe

Line238 Programming Guide4.8.2 PC Console Line 2/2Used to assign parameters for PC Console lines.Parameter [Call Log Incoming] Lock PasswordDefault Bl

LineProgramming Guide 239Parameter Intercept Destination – Day / NightDefault BlankValue Range 3-4 digits consisting of 0-9Description/Function Specif

Configuration24 Programming GuideParameter DN ReferDefault —Value Range —Description/Function Displays the list of DNs/FDNs which are already assigned

Line240 Programming Guide

FeaturesProgramming Guide 241Section 5Features

Features242 Programming Guide5.1 FeaturesUsed to assign parameters for various system features.

FeaturesProgramming Guide 2435.2 System Speed DiallingUsed to programme a list of up to 1000 (000-999) frequently dialled numbers per tenant.Anyone in

Features244 Programming GuideParameter Entry No.Default 000-019Value Range 000-999 in 20 codes incrementsDescription/Function Specifies the entry numb

FeaturesProgramming Guide 245Parameter NameDefault BlankValue Range Up to 10 characters consisting of 0-9, A-Z, a-z or the followingmarks:!#$% ()+,-/:

Features246 Programming Guide5.3 Phantom ExtensionUsed to register up to 448 Phantom Extension numbers.Parameter Entry No.Default 001-048Value Range 0

FeaturesProgramming Guide 247Parameter DN ReferDefault —Value Range —Description/Function Displays the list of DNs/FDNs which are already assigned to

Features248 Programming Guide5.4 Emergency Dial CodeUsed to programme a list of up to 10 emergency numbers that any extension in the system candial at

FeaturesProgramming Guide 2495.5 Quick DiallingUsed to store up to eight Quick Dialling numbers.Parameter DialDefault All: BlankValue RangeUp to 24 di

ConfigurationProgramming Guide 251.6 T1 Port AssignmentUsed to assign parameters for T1 ports.HowtosetupaT1card1. Insert T1 card into a free slot.Note

Features250 Programming Guide5.6 Account CodeUsed to programme a list of up to 1000 account codes which are used to identify incoming andoutgoing CO c

FeaturesProgramming Guide 251Parameter CodeDefault BlankValue Range Up to 10 digits consisting of 0-9Description/Function Specifies the account codes.

Features252 Programming Guide5.7 Special Carrier CodeUsed to programme a list of up to 100 Special Carrier Codes.Parameter CodeDefault BlankValue Rang

FeaturesProgramming Guide 2535.8 Waiting Second Dial Tone CodeUsed to assign parameters for the Waiting Second Dial Tone feature.Parameter Entry No.De

Features254 Programming GuideParameter ModeDefault DisableValue Range1. Enable2. DisableDescription/Function Specifies whether Waiting Second Dial Ton

FeaturesProgramming Guide 2555.9 Absent MessageUsed to programme a list of up to nine absent messages.An absent message, if set by the extension user,

Features256 Programming GuideParameter MessageDefault MSG1: Will Return Soon, MSG2: Gone Home, MSG3: At Ext%%%% (Extension No.), MSG4: Back at %% : %%

FeaturesProgramming Guide 2575.10 DISA/TIE User CodeUsed to programme a list of up to 32 DISA/TIE User Codes.Each code is appended with a COS level.

Features258 Programming GuideParameter CodeDefault All: BlankValue Range 4-10 digits consisting of 0-9Description/Function Specifies the User Codes fo

FeaturesProgramming Guide 2595.11 VPS Integration5.11.1 VPS Integration 1/2Used to assign Integration Code and Voice Mail Command for VPS Integration.

Configuration26 Programming GuideParameter Card No.Default —Value Range XXX : T1 [ XXX : Card No. (101-314)]Description/Function Specifies the physica

Features260 Programming GuideParameter [Integration Code] Busy ToneDefault 2Value RangeUp to 3 digits consisting of 0-9, or #Description/Function Spec

FeaturesProgramming Guide 261Parameter [Integration Code] Extension DisconnectionDefault #9Value RangeUp to 3 digits consisting of 0-9, or #Descriptio

Features262 Programming GuideVoice Mail CommandVoice Mail Commands are used to control the activity of Voice Mail port.There are the following four Vo

FeaturesProgramming Guide 263Parameter [Voice Mail Command] Get MessageDefault *HValue RangeUp to 16 digits consisting of 0-9, , # or HDescription/Fun

Features264 Programming Guide5.11.2 VPS Integration 2/2Used to assign optional parameters for VPS Integration.Parameter DTMF signal durationDefault 80

FeaturesProgramming Guide 265Parameter Pause timing before sending DTMF signal (RBT, BT)Default 1.5 sValue Range1. 0.5 s2. 1.0 s3. 1.5 s4. 2.0 sDescri

Features266 Programming GuideParameter Extension's mailbox numberDefault Programmed numberValue Range1. Extension number2. Programmed numberDescr

FeaturesProgramming Guide 267Parameter Sending out Follow-on ID after IRNADefault DisableValue Range1. Disable2. EnableDescription/Function Specifies

Features268 Programming Guide5.12 Caller ID ModificationUsed to modify the telephone number sent from the Central Office by Caller ID Service tomake u

FeaturesProgramming Guide 269Parameter [Local Call] Digits to deleteDefault No.1: 3, Others: 0Value Range 0-9Description/Function Specifies the number

ConfigurationProgramming Guide 27Parameter Group No.Default BlankValue Range 1-48 or 1-128Description/Function Channel Type : LCO, GCO, DID, TIE (E&am

Features270 Programming GuideParameter [Long Distance Call] Number to be addedDefault 1Value RangeUp to 4 digits consisting of 0-9, or #Description/Fu

FeaturesProgramming Guide 2715.13 Caller ID Registration5.13.1 Caller ID RegistrationUsed to assign the Caller ID code (identification code of the cal

Features272 Programming Guidec) Click to continue the operation.• The message "Import..." is displayed and copying the System Speed Dial dat

FeaturesProgramming Guide 273Parameter NameDefault BlankValue Range Up to 16 characters consisting of 0-9, A-Z, a-z or the followingmarks:!#$% ()+,-/:

Features274 Programming Guide5.14 UCD Time TableIf all extensions in a UCD group are busy, the incoming CO calls will be handled by the UCDTime Table

FeaturesProgramming Guide 275Parameter Command Sequence (1-16)Default NoneValue Range None,S1-S8,1T-4T,TR,RET,OFFDescription/Function The following co

Features276 Programming Guide5.15 ChargeUsed to assign parameters for the Charge Fee Management feature.Parameter Charge Display on LCDDefault MeterVa

FeaturesProgramming Guide 277Parameter [Charge Verification ID Code] Tenant 1-8Default 1234Value Range 4-7 digits consisting of 0-9Description/Functio

Features278 Programming GuideParameter Currency Display PositionDefault TailValue Range1. Head2. TailDescription/Function Specifies whether the curren

FeaturesProgramming Guide 2795.16 HotelUsed to assign parameters for Hotel Application.Parameter [Charge] MarginDefault 0.0 %Value Range 0-999.9 %Desc

Configuration28 Programming Guide1.7 E1 Port AssignmentUsed to assign parameters for E1 ports.How to set up an E1 card1. Insert E1 card into a free sl

Features280 Programming GuideParameter [Charge] TAX1Default 30.0 %Value Range 0-200.0 %Description/Function Specifies a tax rate which applies to the

FeaturesProgramming Guide 281Parameter [Title] 1Default TelephoneValue Range Up to 10 characters consisting of 0-9, A-Z, a-z or the followingmarks:!#$

Features282 Programming GuideParameter TitleHeader(3lines)Default Check Out SheetValue Range Characters consisting of 0-9, A-Z, a-z or the following m

FeaturesProgramming Guide 283Parameter [Data Start] LineDefault 4Value Range 4-24Description/Function Specifies the start line of the data portion.Ref

Features284 Programming Guide

Toll RestrictionProgramming Guide 285Section 6Toll Restriction

Toll Restriction286 Programming Guide6.1 Toll RestrictionUsed to assign TRS (Toll Restriction) Deny Codes and TRS Exception Codes.

Toll RestrictionProgramming Guide 2876.2 TRS Deny CodeUsed to programme a list of up to 400 TRS (Toll Restriction) Deny Codes - telephone numbersthat

Toll Restriction288 Programming GuideParameter DialDefault BlankValue RangeUp to 10 digits consisting of 0-9, X, or #Description/Function Specifies th

Toll RestrictionProgramming Guide 2896.3 TRS Exception CodeUsed to programme a list of numbers that an extension is allowed to dial, even if these num

ConfigurationProgramming Guide 29Parameter Card No.Default —Value Range XXX : E1 [ XXX : Card No. (101-314)]Description/Function Specifies the physica

Toll Restriction290 Programming GuideParameter DialDefault BlankValue RangeUp to 10 digits consisting of 0-9, X, or #Description/Function Specifies th

ARS (Automatic Route Selection)Programming Guide 291Section 7ARS (Automatic Route Selection)

ARS (Automatic Route Selection)292 Programming Guide7.1 ARS (Automatic Route Selection)Used to assign ARS parameters.

ARS (Automatic Route Selection)Programming Guide 2937.2 Time TableUsed to make up ARS time schedules. It is possible to split a day into four time zon

ARS (Automatic Route Selection)294 Programming Guide7.3 Leading Digits TableUsed to determine the appropriate Route Plan Table number for a call by an

ARS (Automatic Route Selection)Programming Guide 295Parameter DialDefault BlankValue RangeUp to 10 digits consisting of 0-9, , # or XDescription/Funct

ARS (Automatic Route Selection)296 Programming Guide7.4 Routing PlanUsed to specify the Trunk Group number (1-48) and Modified Digit Table number (1-4

ARS (Automatic Route Selection)Programming Guide 297Parameter [Time-A, -B, -C, -D] Modification Table No.Default NoneValue Range None, 1-48Description

ARS (Automatic Route Selection)298 Programming Guide7.5 Digits Modification TableUsed to modify the user-dialled number so that it matches the require

ARS (Automatic Route Selection)Programming Guide 299Parameter Number to be addedDefault BlankValue RangeUp to 20 digits consisting of 0-9, , # or P [P

Table of ContentsProgramming Guide 3Table of Contents1 Configuration...

Configuration30 Programming GuideParameter Receiver TypeDefault UndefinedValue Range1. Undefined2. Pulse3. DTMF4. MFC-R2Description/Function Specifies

ARS (Automatic Route Selection)300 Programming Guide

Private NetworkProgramming Guide 301Section 8Private Network

Private Network302 Programming Guide8.1 Private NetworkUsed to assign parameters required to utilise TIE line service.

Private NetworkProgramming Guide 3038.2 TIE Routing TableUsed to specify trunk groups and parameters required for making TIE calls.This table is refer

Private Network304 Programming GuideParameter Leading DigitDefault BlankValue Range Up to 3 digits consisting of 0-9 or XDescription/Function Specifie

DDI / DIDProgramming Guide 305Section 9DDI / DID

DDI / DID306 Programming Guide9.1 DDI/DIDUsed to assign parameters required to utilise DDI/DID service.

DDI / DIDProgramming Guide 3079.2 Number Transformation9.2.1 Number TransformationUsed to specify several parameters for DDI / DID / MSN service.Param

DDI / DID308 Programming GuideParameter DDI / DID / MSN No.Default BlankValue Range Up to 16 digits consisting of 0-9Description/Function Specifies th

DDI / DIDProgramming Guide 309Parameter Destination – Day / NightDefault BlankValue Range 3-4 digits consisting of 0-9Description/Function Specifies t

ConfigurationProgramming Guide 311.8 DISA Port AssignmentUsed to assign OGM group number for each DISA card.Parameter [Card No. 1-8] LocationDefault (

DDI / DID310 Programming Guide9.2.2 Automatic Registration of DDI / DID / MSN NumbersProvides quick registration of DDI / DID / MSN numbers.Up to 100

DDI / DIDProgramming Guide 311Entry No.99 : 123456 (98)Entry No.100 : 123456 (99)Notes• If more than 15 digits are entered in "[Base Number] Dial

DDI / DID312 Programming GuideParameter [Additional Number] Number of DigitsDefault 2 digits (00-99)Value Range 1-16 digitsDescription/Function Specif

MaintenanceProgramming Guide 313Section 10Maintenance

Maintenance314 Programming Guide10.1 MaintenanceUsed to assign parameters for system maintenance.

MaintenanceProgramming Guide 31510.2 External Modem 1/2The system supports an external modem plugged into the RS-232C port for remote systemadministra

Maintenance316 Programming GuideParameter Automatic Initialization CommandDefault AT&F0Q0E0V1S0=1X0&D0Value Range Up to 80 characters consisti

MaintenanceProgramming Guide 31710.3 External Modem 2/2Parameter Connection Message (1-5)Default Message 1: CONNECT, Others: BlankValue Range Up to 80

Maintenance318 Programming Guide10.4 SMDR10.4.1 SMDR 1/2Station Message Detail Recording (SMDR) automatically records detailed information foroutside

MaintenanceProgramming Guide 319Parameter Output TypeDefault Type-AValue Range1. Type-A2. Type-B3. Type-C4. Type-D5. Type-EDescription/Function Specif

Configuration32 Programming Guide1.9 BRI Port AssignmentUsed to assign the parameters for BRI (Basic Rate Interface) ports.Parameter Card No.Default —

Maintenance320 Programming GuideParameter [Format] Skip PerforationDefault 0Value Range 0-95 linesDescription/Function Determines the number of lines

MaintenanceProgramming Guide 321Parameter Print out Caller ID InformationDefault NumberValue Range1. Number2. Number + Name3. Name4. DisableDescriptio

Maintenance322 Programming GuideParameter Print out Timed Reminder InformationDefault DisableValue Range1. Enable2. DisableDescription/Function If thi

MaintenanceProgramming Guide 323Parameter Print out Absent Message (6-9)Default DisableValue Range1. Enable2. DisableDescription/Function Specifies wh

Maintenance324 Programming Guide10.4.2 SMDR 2/2Station Message Detail Recording (SMDR) automatically records detailed information foroutside calls.Par

MaintenanceProgramming Guide 32510.5 Power Failure TransferPower Failure Transfer connects specific telephones (any SLT and a certain type of APT) top

Maintenance326 Programming GuideParameter Extension Card (1-24)Default NoneValue Range None, XXX : YYY [XXX : Card No. (101-314), YYY : Card Type]Desc

MaintenanceProgramming Guide 32710.6 System ParametersUsed to assign various system parameters.Passwords for System Programming by PCRequired to perfo

Maintenance328 Programming Guidec) Please change the password periodically.d) We strongly recommend that you set the system password to 7 digits for m

MaintenanceProgramming Guide 329Parameter [Password] System Programming – Protection Level 2Default 1234Value Range 4-7 digits of alphanumeric charact

ConfigurationProgramming Guide 33Parameter TypeDefault COValue Range1. CO2. EXT3. Qsig – Master4. Qsig – SlaveDescription/Function Specifies the type

Maintenance330 Programming Guide[Serial Interface Port] PROG (Port 1)Please refer to "System Programming and Diagnosis with Personal Computer&quo

MaintenanceProgramming Guide 331[Serial Interface Port] SMDR (Port 2)Please refer to "Station Message Detail Recording (SMDR)" of Section &q

Maintenance332 Programming GuideParameter [Serial Interface Port] SMDR – ParityDefault NoneValue Range1. None2. Mark3. Space4. Even5. OddDescription/F

MaintenanceProgramming Guide 333Parameter [Serial Interface Port] SMDR – Stop BitDefault 1bitValue Range1. 1bit2. 2bitsDescription/Function A stop bit

Maintenance334 Programming GuideParameter [Remote Connect Information] Dial NumberDefault BlankValue Range Up to 40 digits consisting of 0-9, "*&

MaintenanceProgramming Guide 33510.7 System TimeUsed to assign System Time.Please refer to the following:• 1.8 Ringing Features (F/G)– Timed Reminder

Maintenance336 Programming GuideParameter (Day)Default 01Value Range 01-31Description/Function Specifies the date in two digits by entering the value

MaintenanceProgramming Guide 337Summer Time / Daylight-saving Time SettingNoteAt 2:00 a.m. on summer time, the system clock will be one hour fast. If

Maintenance338 Programming GuideParameter End (Day)Default BlankValue Range 01-31Description/Function Specifies the date in two digits by entering the

Programming Error MessagesProgramming Guide 339Section 11Programming Error Messages

Configuration34 Programming GuideParameter Group No.Default 1Value Range 1-48 or 1-128Description/Function Type: CO, Qsig-Master, Qsig-SlaveSpecifies

Programming Error Messages340 Programming Guide11.1 Error Messages (EXXXX)Error CodeError MessageDescriptionE0000 System error. (Error code : XXX)A sy

Programming Error MessagesProgramming Guide 341E0012 Another maintenance device is connected.There are three ways to access the PBX: (1) By PC System

Programming Error Messages342 Programming GuideE1006 You have exceeded the system limit of AGC cards.There is a limit of 8 AGC cards per system.E1007

Programming Error MessagesProgramming Guide 343E1023 Assign the directory numbers for EXT#1 and EXT#2.For the VPS port you must assign directory numbe

Programming Error Messages344 Programming GuideE1037 Cannot change the status of the port.Cannot change the status of the SLT port because the PT port

Programming Error MessagesProgramming Guide 345E1059 VPS card duplicated.Each physical number of the VPS Card (Jack 1-8) and VPS Card (Jack 9-12) must

Programming Error Messages346 Programming GuideE2013 Invalid directory number for Operator FDN.Only FDN of an extension group and incoming group can b

Programming Error MessagesProgramming Guide 347E4007 Single - CO key duplicated.Please assign the Single - CO key that has the different CO physical n

Programming Error Messages348 Programming GuideE4024 DN or FDN must be entered to assign the type of key.You must enter the DN or FDN when you assign

Programming Error MessagesProgramming Guide 349E5006 Cannot assign more than 1000 account codes.There is a limit of 1000 account codes per system.E500

ConfigurationProgramming Guide 351.10 PRI Port AssignmentUsed to assign the parameters for PRI (Prime Rate Interface) ports.Parameter Card No.Default

Programming Error Messages350 Programming GuideE9001 Invalid directory number for DDI / DID destination.There are seven possible destinations for DDI

Programming Error MessagesProgramming Guide 35111.2 Warning Messages (WXXXX)CodeMessageDescriptionW0001 Save system data?Some parameters on the screen

Programming Error Messages352 Programming GuideW3002 Please verify that previously erased FDN is not programmed in other screens.The erased FDN may be

Programming Error MessagesProgramming Guide 353W5010 Voice Mail command must not exceed 16 digits. Truncate it?Truncate means that the leading 16 digi

Programming Error Messages354 Programming GuideW9005 Base dial number must not exceed 15 digits. Truncate it?Truncate means that the leading 15 digits

Programming Error MessagesProgramming Guide 35511.3 Information Message (IXXXX)CodeMessageDescriptionI0001 Upload completed. Please change PBX to on-l

Programming Error Messages356 Programming Guide

Default ValuesProgramming Guide 357Section 12Default Values

Default Values358 Programming Guide1 Configuration1.1 Configuration1.2 Slot Assignment1.3 Trunk Port Assignment1.4 Extension Port Assignment1.5 VPS (D

Default ValuesProgramming Guide 3591.6 T1 Port Assignment1.7 E1 Port Assignment1.8 DISA Port AssignmentType NoneJack No. (Display only)Port No. Blank[

Configuration36 Programming GuideParameter TypeDefault COValue Range1. CO2. EXT3. Qsig – Master4. Qsig – SlaveDescription/Function Specifies the type

Default Values360 Programming Guide1.9 BRI Port Assignment1.10 PRI Port Assignment2 System2.1 System2.2 Tenant[Card No. 1-8] OGM Group No. 1Programme

Default ValuesProgramming Guide 3612.3 Numbering PlanDay (SUN-SAT) 9:00 AMNight (SUN-SAT) 5:00 PMLunch - Start (SUN-SAT) 12:00 PMLunch - End (SUN-SAT)

Default Values362 Programming Guide19 Trunk Group Access 820 Speed Dialing - System *21 Speed Dialing - Station 3*22 Speed Dialing - Station Programmi

Default ValuesProgramming Guide 36350 Station Lock Set / Cancel 76251NightModeSet/Cancel 7852 Parallel Telephone Mode 3953 External BGM On / Off 3554

Default Values364 Programming Guide2.4 Class of Service (COS)2.4.1 Class of Service (COS) 1/2103 Group Login / Logout 48104 Group FWD 714105 Print out

Default ValuesProgramming Guide 3652.4.2 Trunk Group Setting2.4.3 Class of Service (COS) 2/22.5 System Timer2.5.1 System Timer 1/2Programme DefaultTru

Default Values366 Programming Guide2.5.2 System Timer 2/22.6 Local Hunt Sequence2.7 Trunk to Trunk Restriction2.8 System Option2.8.1 System Option 1Pr

Default ValuesProgramming Guide 3672.8.2 System Option 22.8.3 System Option 35. Limited call duration Both calls6. Transfer recall destination Origina

Default Values368 Programming Guide2.8.4 System Option 426. Pressing CO/DN/Answer key operation intalkingHold27. Message Waiting lamp pattern #1128. T

Default ValuesProgramming Guide 3692.8.5 System Option 52.8.6 System Option 6Programme Default50. Dial / Ringback tone frequency Normal51. Release of

ConfigurationProgramming Guide 37Parameter Group No.Default 1Value Range 1-48 or 1-128Description/Function Type: CO, Qsig-Master, Qsig-SlaveSpecifies

Default Values370 Programming Guide2.9 Language Data3Group3.1 Group3.2 Trunk Group3.2.1 Trunk Group 1/2Programme DefaultGroup No. 1Type PublicCopy —In

Default ValuesProgramming Guide 3713.2.2 Trunk Group 2/23.3 Extension Group3.4 Paging GroupProgramme DefaultISDN Progress Tone Mode AutomaticSending I

Default Values372 Programming Guide3.5 Incoming Group3.5.1 Destination for Incoming GroupExtension Group No. Paging Group No.1 = No.1: 1, No.2: 128, O

Default ValuesProgramming Guide 3733.6 OGM Group4Line4.1 Line4.2 Trunk LineProgramme DefaultGroup No. 1FDN BlankDN Refer —Tenant No. 1OGM Type DISASec

Default Values374 Programming Guide[DDI / DID / TIE] Number to be added BlankDigit to receive DDI / DID 4 (DID / DID-2W / DID-MFC / E1[DR2] / T1[DID]c

Default ValuesProgramming Guide 3754.3 Extension Line4.3.1 Extension Line 1/2Programme DefaultCard No. —Port No. 1DN —Group No. (Display only)Copy —Na

Default Values376 Programming Guide4.3.2 Flexible CO Key Assignment4.3.3 Flexible PF Key Assignment for PT4.3.4 Extension Line 2/24.4 DSS ConsoleISDN

Default ValuesProgramming Guide 3774.4.1 Flexible DSS Key Assignment4.4.2 Flexible PF Key Assignment for DSS Console4.5 Doorphone4.6 External Paging4.

Default Values378 Programming Guide4.8 PC Console Line4.8.1 PC Console Line 1/2Charge Limit 0Tone DisableISDN Bearer Mode AutomaticNumbering Plan ID D

Default ValuesProgramming Guide 3794.8.2 PC Console Line 2/25Features5.1 Features5.2 System Speed Dialling[Pickup Dialing] Mode Disable[Pickup Dialing

Configuration38 Programming Guide

Default Values380 Programming Guide5.3 Phantom Extension5.4 Emergency Dial Code5.5 Quick Dialling5.6 Account Code5.7 Special Carrier CodeCurrent Regis

Default ValuesProgramming Guide 3815.8 Waiting Second Dial Tone Code5.9 Absent Message5.10 DISA/TIE User Code5.11 VPS Integration5.11.1 VPS Integratio

Default Values382 Programming Guide5.11.2 VPS Integration 2/25.12 Caller ID Modification[Integration Code] FWD to VM Ringback Tone 6[Integration Code]

Default ValuesProgramming Guide 3835.13 Caller ID Registration5.13.1 Caller ID Registration5.14 UCD Time Table5.15 Charge5.16 HotelProgramme DefaultTe

Default Values384 Programming Guide6 Toll Restriction6.1 Toll Restriction6.2 TRS Deny Code6.3 TRS Exception Code[Charge] TAX3 30.0 %[Title] 1 Telephon

Default ValuesProgramming Guide 3857 ARS (Automatic Route Selection)7.1 ARS (Automatic Route Selection)7.2 Time Table7.3 Leading Digits Table7.4 Routi

Default Values386 Programming Guide8 Private Network8.1 Private Network8.2 TIE Routing Table9DDI/DID9.1 DDI/DID9.2 Number Transformation9.2.1 Number T

Default ValuesProgramming Guide 38710 Maintenance10.1 Maintenance10.2 External Modem 1/210.3 External Modem 2/210.4 SMDR10.4.1 SMDR 1/2Beginning Entry

Default Values388 Programming Guide10.4.2 SMDR 2/210.5 Power Failure Transfer10.6 System ParametersPrint out LOGIN / LOGOUT DisablePrint out Absent Me

Default ValuesProgramming Guide 38910.7 System Time[Serial Interface Port] PROG – Baud Rate 19200 bps[Serial Interface Port] SMDR (Port 2)[Serial Inte

SystemProgramming Guide 39Section 2System

Default Values390 Programming Guide11 Programming Error Messages11.1 Error Messages (EXXXX)11.2 Warning Messages (WXXXX)11.3 Information Message (IXXX

Default ValuesProgramming Guide 391

Default Values392 Programming Guide

Default ValuesProgramming Guide 393

Kyushu Matsushita Electric Co., Ltd.1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, JapanPrinted in JapanPSQX2859ZA2002 Kyushu Matsushita Elect

Table of Contents4 Programming Guide5.5 Quick Dialling ...

System40 Programming Guide2.1 SystemUsed to assign parameters which affect system-wide operation.

SystemProgramming Guide 412.2 TenantUsed to assign various parameters on a tenant (1-8) basis.Parameter Tenant No.Default 1Value Range 1-8Description/

System42 Programming GuideParameter Alert Extension - Day / NightDefault BlankValue Range 3-4 digits consisting of 0-9Description/Function Specifies t

SystemProgramming Guide 43(Auto Start Time)Specifies "Start" time of DAY / NIGHT / LUNCH / BREAK service on a day of the week basis.(This se

System44 Programming GuideParameter Lunch - Start (SUN-SAT)Default 12:00 PMValue Range Same as DayDescription/Function Specifies the start time for Lu

SystemProgramming Guide 45Parameter Music on Hold SourceDefault MUS1Value Range1. None2. MUS13. MUS24. ToneDescription/Function Specifies the Music So

System46 Programming GuideParameter System Speed Dialing Entries Max.Default Tenant No. 1:1000, Tenant No. 2:1000, Tenant Nos. 3-8:0Value Range 0-1000

SystemProgramming Guide 47Parameter System Speed Dial TRS Level OverrideDefault No checkValue Range1. Check [Enable]2. No check [Disable]Description/F

System48 Programming Guide2.3 Numbering PlanUsed to assign the leading digits of extension numbers, and feature numbers for systemfeatures.Parameter 1

SystemProgramming Guide 49Parameter 2 2nd Hundred Block ExtensionDefault 11Value Range 1-2 digits consisting of 0-9Description/Function Same as the Pa

ConfigurationProgramming Guide 5Section 1Configuration

System50 Programming GuideParameter 7 7th Hundred Block ExtensionDefault 21Value Range 1-2 digits consisting of 0-9Description/Function Same as the Pa

SystemProgramming Guide 51Parameter 11-16 11th Hundred Block Extension - 16th Hundred BlockExtensionDefault BlankValue Range 1-2 digits consisting of

System52 Programming GuideParameter 20 Speed Dialing - SystemDefault *Value Range1-4 digits consisting of 0-9, or #Description/Function Specifies the

SystemProgramming Guide 53Parameter 25 External Paging Answer / TAFAS AnswerDefault 42Value Range1-4 digits consisting of 0-9, or #Description/Functio

System54 Programming GuideParameter 29 Group Call PickupDefault 40Value Range1-4 digits consisting of 0-9, or #Description/Function Specifies the feat

SystemProgramming Guide 55Parameter 33 Hold Retrieve - TrunkDefault 53Value Range1-4 digits consisting of 0-9, or #Description/Function Specifies the

System56 Programming GuideParameter 38 External Feature AccessDefault 6Value Range1-4 digits consisting of 0-9, or #Description/Function Specifies the

SystemProgramming Guide 57Parameter 42 Call FWD - Do Not Disturb Set / CancelDefault 710Value Range1-4 digits consisting of 0-9, or #Description/Funct

System58 Programming GuideParameter 46 Executive Busy Override Deny Set / CancelDefault 733Value Range1-4 digits consisting of 0-9, or #Description/Fu

SystemProgramming Guide 59Parameter 50 Station Lock Set / CancelDefault 762Value Range1-4 digits consisting of 0-9, or #Description/Function Specifies

Configuration6 Programming Guide1.1 ConfigurationUsed to determine the basic system configuration.

System60 Programming GuideParameter 54 Live Call ScreeningDefault 799Value Range1-4 digits consisting of 0-9, or #Description/Function Specifies the f

SystemProgramming Guide 61Parameter 58 Login / LogoutDefault 45Value Range1-4 digits consisting of 0-9, or #Description/Function Specifies the feature

System62 Programming GuideParameter 62 MCIDDefault 737Value Range1-4 digits consisting of 0-9, or #Description/Function Specifies the feature number f

SystemProgramming Guide 63Parameter 73 Remote FWD Cancel-OnceDefault 723Value Range1-4 digits consisting of 0-9, or #Description/Function With this fe

System64 Programming GuideParameter 77-92 Other PBX 01 - Other PBX 16Default BlankValue Range 1-2 digits consisting of 0-9Description/Function Specifi

SystemProgramming Guide 65Parameter 96 CLIP / COLPDefault 711Value Range1-4 digits consisting of 0-9, or #Description/Function Specifies the feature n

System66 Programming GuideParameter 100 COS PrimaryDefault 792Value Range1-4 digits consisting of 0-9, or #Description/Function Specifies the feature

SystemProgramming Guide 67Parameter 104 Group FWDDefault 714Value Range1-4 digits consisting of 0-9, or #Description/Function Specifies the feature nu

System68 Programming Guide2.4 Class of Service (COS)2.4.1 Class of Service (COS) 1/2Used to assign the Class of Service (COS) parameters.Parameter COS

SystemProgramming Guide 69Parameter TRS Level – Day / NightDefault 1Value Range 1-8Description/Function Specifies the Toll Restriction level (1-8) for

ConfigurationProgramming Guide 71.2 Slot AssignmentAssigns the type of service cards, inserted in the free slots in the basic and expansion shelves.No

System70 Programming GuideParameter Switching Day / Night ModeDefault DisableValue Range1. Enable2. DisableDescription/Function Enables or disables sw

SystemProgramming Guide 71Parameter Transfer to CODefault DisableValue Range1. Enable2. DisableDescription/Function Enables or disables "Call Tra

System72 Programming GuideParameter CallFWDFollowMeDefault EnableValue Range1. Enable2. DisableDescription/Function Enables or disables "Call For

SystemProgramming Guide 73Parameter Released Link OperationDefault DisableValue Range1. Enable2. DisableDescription/Function Used to turn on / off &qu

System74 Programming GuideParameter Automatic HoldDefault DisableValue Range1. Enable2. DisableDescription/Function Used to turn on / off "Automa

SystemProgramming Guide 752.4.2 Trunk Group SettingUsed to specify the trunk group that the extension user can use for making an outside call.The foll

System76 Programming Guide2.4.3 Class of Service (COS) 2/2Used to assign the Class of Service (COS) parameters.Parameter Trunk Group No. 01-48 – Day /

SystemProgramming Guide 77Parameter Secret Busy OverrideDefault DisableValue Range1. Enable2. DisableDescription/Function Enables or disables "Se

System78 Programming GuideParameter Incoming Group FWDDefault DisableValue Range1. Disable2. Own Group(s)3. Any GroupDescription/Function Enables or d

SystemProgramming Guide 792.5 System Timer2.5.1 System Timer 1/2Used to assign various system timers.Parameter Hold Recall TimeDefault 60 sValue Range

Configuration8 Programming GuideParameter Card TypeDefault BlankValue Range Please refer to "Description/Function."Description/Function Spec

System80 Programming GuideParameter Transfer Recall TimeDefault 12 ringsValue Range 0-48 ringsDescription/Function Specifies the number of rings befor

SystemProgramming Guide 81Parameter Call Duration Count Start TimeDefault 0sValue Range 0-60 sDescription/Function Specifies the length of time in sec

System82 Programming GuideParameter Intercept TimeDefault 12 ringsValue Range 1-48 ringsDescription/Function Specifies the number of rings the system

SystemProgramming Guide 83Parameter Extension-to-CO Line Call Duration TimeDefault 10 minValue Range 1-64 minDescription/Function Specifies the maximu

System84 Programming GuideParameter Automatic Redial Repeat TimesDefault 3 times: [NZ], 10 times: [HK], [SA], 4 times: OthersValue Range 0-30 timesDes

SystemProgramming Guide 852.5.2 System Timer 2/2Used to assign various system timers.Parameter Timed Reminder Ringing TimeDefault 30 sValue Range 30-2

System86 Programming GuideParameter Call Parking Recall TimeDefault 60 sValue Range 0-1800 sDescription/Function Specifies the length of time in secon

SystemProgramming Guide 87Parameter DISA Delayed Answer TimeDefault 1ringValue Range 0-6 ringsDescription/Function Specifies the number of rings the s

System88 Programming GuideParameter DISA IRNA TimeDefault 60 sValue Range 5-240 sDescription/Function Specifies the length of time in seconds the syst

SystemProgramming Guide 89Parameter Timed Reminder Arrive Wait TimeDefault 60 sValue Range 20-240 sDescription/Function Specifies the interval time be

ConfigurationProgramming Guide 9Parameter Card TypeDescription/Function Notes• To change the current Card Type to a new one, delete thecurrent setting

System90 Programming Guide2.6 Local Hunt SequenceSpecifies the trunk group hunt sequence to be used when an extension user attempts to makean outside

SystemProgramming Guide 912.7 Trunk to Trunk RestrictionUsed to allow or restrict the trunk-to-trunk relay function (routing a trunk call from one Tru

System92 Programming Guide2.8 System Option2.8.1 System Option 1Used to assign system option parameters (No.1 — No.10).Parameter 1. Sound source durin

SystemProgramming Guide 93Parameter 2. SLT On-hook with consulting held callDefault Consulting HoldValue Range1. Consulting Hold2. DisconnectDescripti

System94 Programming GuideParameter 5. Limited call durationDefault Both callsValue Range1. Outgoing call only2. Both callsDescription/Function Limite

SystemProgramming Guide 95Parameter 7. Checking dial *, # by toll restrictionDefault CheckValue Range1. No check [Disable]2. Check [Enable]Description

System96 Programming Guide2.8.2 System Option 2Used to assign system option parameters (No.11 – No.20).Parameter 10. Station Speed Dialing Initial dis

SystemProgramming Guide 97Parameter 12. Automatic adjustment of the clock usingCaller ID informationDefault NoValue Range1. Yes2. NoDescription/Functi

System98 Programming GuideParameter 15. Special dial tone after setting featureDefault EnableValue Range1. Enable2. DisableDescription/Function If ena

SystemProgramming Guide 99Parameter 17. Destination Busy - DISADefault Send busy toneValue Range1. Send busy tone2. Transferred to IRNA destinationDes