Panasonic WV-SW152ME Installation Guide

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number i

10PrecautionsRefer installation work to the dealer.Installation work requires technique and experi-ences. Failure to observe this may cause fire, elec

11Do not touch this product or the connect-ed cables during thunder. (even in the pro-cess of work)Failure to observe this may cause electric shock.Tu

12 • When some SDHC/SD memory cards are used with this product, the product may not work properly or performance deterio-ration may be caused. U

13Precautions for installationThis product is designed to be installed under eaves.Install the product under eaves to avoid direct sunlight.Installing

14Do not remove or loosen the internal cam-era screwsDo not loosen the internal camera screws. Otherwise, water exposure may cause damage or mal

15About the initial set buttonAfter turning off the power of the camera, turn on the power of the camera while holding down this button, and wait for

16Important: • Remove the cover film attached to the dome after the camera installation is completed. After removing the cover film, do not t

17When installing the camera on a ceiling or a wall, there are three methods as specified below. • Directly mounting to a ceiling or a wall • Use

18Method of camera installationInstalling the camera directly on the ceiling or wallNote: • Use the installation template label (accessory) with the

19Using the mount bracket (accessory)Note: • When the camera is mounted on the ceiling or wall with a hole for cable running and the cables are pass

2The serial number of this product may be found on the surface of the unit.You should note the model number and serial number of this unit in the spac

20<Connecting the cable through holes opened in the ceiling or wall>Place the installation template label (accessory) on the ceiling or wall, ma

21Using a one-gang junction box • Secure the mount bracket (accessory) to the one-gang junction box built in a ceiling or a wall.Note: • Ceiling i

22Important: • Before inserting the SDHC/SD memory card, turn off the power of the camera first. • When inserting an SDHC/SD memory card, make sur

23Before starting the connection, turn off the power of the devices to be connected.Check and prepare the required devices and cables for connection.N

24Important: • Use all 4 pairs (8 pins) of the LAN cable. • The maximum cable length is 100 m {328 feet}. • Make sure that the PoE device in us

25Connection example<Required cable>LAN cable (category 5 or better, straight)Important: • Use a switching hub which is compliant with 10BASE

26Camera mounting<Installing the camera directly on the ceiling or wall>z Remove the dome cover. (3 screws) (☞ Page 16)x Connect the cables to t

27<Using a one-gang junction box> z Connect each cable. • Apply waterproof treatment to all connections. (☞ Page 24)x Secure the mount bracke

28Using the side cable access hole When installing the camera directly on the ceiling or wall with cables exposed, cut off a portion of the mount bra

29z Adjust the camera angle.When determining the camera angle, repeat fine adjustments by gradually moving the panning table and tilting table. • A

3ContentsImportant safety instructions ... 4Limi

30Note: • Depending on the vertical/horizontal angle used, the edges of the camera may be projected. • Use Extra Zoom when you want to adjust

31z Attach the dome cover to the camera by using the tamperproof screw bit (accessory) to tighten the 3 dome cover fixing screws (M3).x Close the sc

32About the CD launcherInsert the provided CD-ROM into the CD-ROM drive of your PC to display the CD launcher win-dow. • If the launcher window

33Installing Panasonic IP setting softwareOn the CD launcher window, click the [Install] button next to [IP Setting Software] to display the Panasonic

34Installing the manualsOn the CD launcher window, click the [Install] button next to [Manual] to display the Manual installa-tion window. Confirm the

35Configure the network settings of the camera using the Panasonic IP setting softwareIt is possible to perform the network settings of the camera usi

36Note: • When using a DHCP server, the IP address assigned to the camera can be displayed by click-ing the [Search] button of the IP setting softwa

37Before asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after checking and tr

38• BasicPower source: PoE (IEEE802.3af compliant)Power consumption: PoE 48 V: 56 mA (Class 1 device)Ambient operating temperature: -30 °C to +50 °

39Max. 10/30s, Max. 16/30sDay & Night (electrical): Off/AutoWhite balance: ATW1/ ATW2/ AWCDigital noise reduction: High/LowVideo analytics Fa

4Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5)

40Image compression method*1: Frame rate: 1fps/ 3fps/ 5fps/ 7.5fps/ 10fps/ 12fps*/ 15fps/ 20fps/ 30fps * E model only JPEG (MJPEG)

41Installation Guide (this document) ...1 pc.Important Safety Instructions ...

42

43

For U.S. and Canada:Panasonic System Networks Company of America,Unit of Panasonic Corporation of North Americawww.panasonic.com/business/For custom

5Limitation of liabilityTHIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMI

6The network cameras WV-SW155/WV-SW155M/WV-SW152/WV-SW152M are designed to oper-ate using a PC on a network (10BASE-T/100BASE-TX), and can be installe

7System requirements for a PCAbout notationsAbout the user manualsThere are 2 sets of operating instructions for the WV-SW155, WV-SW155M, WV-SW152, WV

8Important: • When using a PC that does not meet the above requirements, displaying of images may become slower or the web browser may

9Network securityAs you will use this unit connected to a network, your attention is called to the following security risks. q Leakage or theft of i