Panasonic WV-CP474H User Manual download pdf (Page 2)

Mounting the Lens

Note: Before you mount the lens, loosen the screw on the side of the camera, and rotate the

ring clockwise until it stops.

If the ring is not at the end, the inner glass or CCD image sensor may be damaged.

1. Attach the supplied C-mount

adapter when using a C-mount

lens.

2. Jump to step 3 if the lens has focus

adjusting mechanism. Loosen the

flange-back screw, and rotate the

adjusting ring down until it stops on

the side of the camera.

3. Mount the lens.

4. Connect the lens cable to the auto

iris connector on the side of the camera.

Flange-back Adjustment

The adjustment is required only when a lens without focus-adjusting mechanism is mounted,

or when a lens with adjusting mechanism is mounted and focus that is more accurate is

needed.

1. Loosen the flange-back fixing screw on the flange-back adjusting ring.

2. Turn the flange-back adjusting ring to obtain a focused point while watching the monitor

screen.

3. Tighten the flange-back fixing screw on the flange-back adjusting ring.

Caution: Tightening the screw by force will cause damage to the screw or deviation of

focus.

Note: The object may be out of focus when using a source of near-infrared light than

using the visible light.

Caution for Mounting the Lens

Follow the indication shown in the figure for the protrusion between a lens and the camera

body. This camera wears mount for use with the CS-mount lens at the factory shipment.

Use the supplied C-mount adapter when using the C-mount lens.

The lens less than 450 g (0.99 lbs) can be mounted on the camera. If the lens is heavier,

both the lens and camera should be

secured by the supporter.

C-mount: Less than 13 mm (1/2”)

CS-mount: Less than 8 mm (5/16”)

MOUNTING LENS/FOCUS ADJUSTMENT

• Mounting from the Top

Remove the mount adapter from the bottom of the camera by removing the two fixing

screws. Attach the mount adapter to the top as shown in the figure, then mount the

camera on the mounting bracket.

Cation:

Be sure to use two original fixing

screws for the mount adapter.

Longer screws may damage the inner

components. Or shorter screws may

cause the camera drop.

INSTALLATION OF CAMERA

Flange-back

Adjusting Ring & Screw

Installation of Auto Iris Lens Connector

Install the lens connector (YFE4191J100) when using a video drive ALC lens.

(1) Cut the iris control cable at the edge of the lens connector to remove the existing lens

connector and then remove the outer cable cover as shown in the figure below.

The pin assignment of the lens connector is as follows:

Pin 1: Power source; +9 V DC, 50 mA max.

Pin 2: Not used

Pin 3: Video signal; 0.7 V[p-p]/40 kΩ

Pin 4: Shield, ground

(2) Solder the lens cable to the pins of the

supplied connector.

Pin 3

Pin 4

Pin 2

Rib

Pin 1

C-mount Adapter

Fixing Screws

Mount Adapter

Lens Mount

■ Connections

Precaution:

The following connections should be made by qualified service personnel or system

installers in accordance with NEC 725-51.

Note: For the WV-CP474E Colour CCTV Camera, do not use a transformer larger than

10 VA.

• Power supply connection

Recommended wire gauge sizes for 24 V AC line.

Cautions:

1. CONNECT THIS TO 24 V AC CLASS 2 POWER SUPPLY ONLY. Be sure to connect

the grounding lead to the GND terminal.

2. To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for

the Input Terminal.

3. The connections should comply with National Electrical Code (NEC).

CONNECTIONS

Alarm Connections

1. Connect an external sensor to the DAY/NIGHT terminal.

2. Connect an external device such as a buzzer or lamp to the ALARM terminal.

• The alarm output terminal is an open collector terminal with a capacity of 16 V DC, 100

mA or less.

OFF: Open contact

ON: 100 mA or less

• Color/black-and-white input terminal with a capacity of 5 V DC pull-up input, 0.2 mA or

more.

OFF: Open contact

ON: Closed contact

Notes:

• Use a relay unit if the voltage or current of the connected device exceeds the ratings.

• To validate the Day/Night function, set BW mode to EXT on the special menu.

Power Cable

Video Output Cable

To Video IN

(CAMERA IN)

BNC Plug

Green/Yellow (Ground)

White (Neutral)

Black (Live)

BNC Plug

24 V AC, 60 Hz

(19.5 V-28 V)

CLASS 2 SUPPLY ONLY)

Copper wire size

(AWG)

#18

(0.83 mm

)

#24

(0.22 mm

)

Length of cable

(Approx.)

(m)

(ft)

#22

(0.33 mm

)

#20

(0.52 mm

)

20 30 45 75

65 100 160 260

Cautions:

1. Shrinking the cable-entry seal is a one-time procedure. Do not shrink the cable-entry

seal until it has been ascertained that the unit is functioning.

2. CONNECT THIS TO 24 V AC CLASS 2 POWER SUPPLY ONLY. Be sure to connect

the grounding lead to the GND terminal.

3. To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for

the Input Terminal.

4. The connections should comply with National electrical Code (NEC).

1 2 3 4 5 6

Comments to this Manuals

No comments

Panasonic WV-CP474H User Manual Page 2

Comments to this Manuals

Related products and manuals for Video surveillance systems Panasonic WV-CP474H