Panasonic CQCB8901U User Manual download pdf (Page 24)

Installation

CQ-CB8901U

Installation

CQ-CB8901U

Caution: Do not disconnect the battery termi-

nals of a car with trip or navigational computer

since all user settings stored in memory will be

lost. Instead take extra care with installing the

unit to prevent shorts.

¡Before installation, check the radio operation with

antenna and speakers.

¡Disconnect the cable from the negative (–) battery

terminal (see caution below).

¡Unit should be installed in a horizontal position

with the front end up at a convenient angle, but

not more than 30°.

Remove Mounting Collar q and Trim Plate r

from the main unit temporarily, which are already

mounted at shipment.

Installation Opening

The unit can be installed in any dashboard having an

opening as shown at right. The dashboard should be

4.5 mm - 6 mm thick in order to be able to support

the unit.

Installation Precautions

This product should be installed by a professional

installer, if possible.

In case of difficulty, please consult the shop where

you purchased the product.

1. This system is to be used only in a 12-volt, DC

battery system (car) with negative ground.

2. Follow the electrical connections carefully (a

Page 50-51). Failure to do so may result in dam-

age to the unit.

3. Connect the power lead (red) after all other con-

nections are made.

4. Be sure to connect the battery lead (yellow) to the

positive terminal (+) of the battery or fuse block

(BAT) terminal.

5. Insulate all exposed wires to prevent short circuit-

ing.

6. Secure all loose wires after installing the unit.

7. Please carefully read the operating and installation

instructions of the respective equipment before

connecting it to this unit.

30° or less

PreparationDashboard Installation

Rear support strap

3 mm

Tapping screw u

To the unit

Hexl nut i

Mounting bolt w

Rear support bracket

(supplied with car)

Rubber bushing (Option)

To the unit

Mounting bolt w

(b) Using the Rubber Bushing (option)

Supplied Hardware

Methods for Fixing the Rear of the Unit.

Q’ty

DiagramItemNo.

Mounting Collar

Mounting Bolt (5 mmø)

Power Connector

Trim Plate

Lock Cancel Plate

Rear Support Strap

Tapping Screw

(5 mmø x 16 mm)

Hex. Nut (5 mmø)

Cautions:

¡We strongly recommend that you wear gloves for installation work to protect yourself from injuries.

When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your

hands and fingers.

w Mounting Bolt

Establish the rear of

the unit.

After fixing Mounting Bolt w

and Power Connector e, fix

the rear of the unit to the car

body by either method (a) or

(b) shown on the previous

page.

Insert Trim Plate r.

After installation reconnect the nega-

tive (–) battery terminal.

First complete the electrical connections, and then check them for correctness. (a Page 50-51)

The included Mounting Collar q is designed spe-

cially for this unit. Do not use it to attach any other

model.

e Power Connector

Insert Mounting Collar q into the dash-

board, and bend the mounting tabs out

with a screwdriver.

Caution:

When this unit is installed in dashboard,

ensure that there is sufficient air flow

around the unit to prevent damage from

overheating, do not block any ventilation

holes on the unit.

Dashboard Installation (continued)

Snapping point

(a) Using the Rear Support Strap

Clank!

1 2 ... 19 20 21 22 23 24 25 26 27

Comments to this Manuals

No comments

Panasonic CQCB8901U User Manual Page 24

Comments to this Manuals

Related products and manuals for CD players Panasonic CQCB8901U