Panasonic WJ-PC10 User Manual

COMPUTE) MTEMFACC ADATrONWJ-PC10OperatingInstructionsJ V. ;;Panasonie.•*•01« 1» COfmc'- 01 op»«*» Mit» !• uPui <«m«e <eaa Mm «mI-xa«#» f.n

1. SW3 ; Selection of the baud rate of RS-232C signal, Turn on one of 6 switches.No.11200 bpsNo.2 2400 bpsNo.34800 bpsNo.49600 bps (Factory set up)No.

Main/Sub selection on SW4 {No.6) in the Extensionmode.The WJ-PC10 located in the control site should be set to Main (OFF) position

GENERAL CONDITION FOR INSTALLATION OF WJ-PC101. tn the Extension-mode a pair ol WJ-PC10 which are designated for the Main and Sub is a

L Camera site J3. In the Extension-mode, the possible numbef of WV-CU300 will be fixed according to the baud rateof RS-232C. Baud rateNumber of WV-CU

The maximum time delay between the Main WJ-PC10 and Sub WJ-PC10 should be less than O.lsec. If the time delay is more than O.lsec

PC MODE SYSTEM- 13 -

2. Extension-mode 1 systemIn this application, the camera sites and the control site are connected with one video transmitting line. Th

optical fiber/ mi ero* wave Contro) site- 15 -

3. Extension-mode 2 systemIn this application, the camera sites and control site are connected with some video transmitting lines. This

VideoMonitor TV- 17 -

ACAUTIONntSK OF ELCCTRtC SHOCK OO NOT OPCNACAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INS

SYSTEM ERROR TABLELED indication CauseTrouble pointsSYS DATA RX No data sync Duplicated data sync• Data Clock Switch on all units are set to RCV posi

1. PC-modeOpen Open(RCV)(SND)Trouble pointError indication LED on WJ-PC10(1) BrokenSYS DATA RX(2) BrokenSYS DATA RX(3) Non-terminationRS-232 TXTrouble

2. Example in Extension-modeBrokenBroken No.1Broken BrokenWJ-MP404(SND)(1)WJ-SQ508|2)WJ-PC10(RCV) (3)-1 Monitor TVnModem —*--4 Modem(3)-2(3)-3RS-232CN

SPECIFICATIONSPower source:Input/output:Controls:Ambient operating temperature: Ambient operating humidity: Dimensions:Weight:12VDC, 0.18AData In/Out;

PanasonicBroadcast & Television Systems CompanyDivision of Matsushita Electric Corporation of America_CLOSED CIRCUIT VIDEO EQUIPMENT DIVISIONExecu

CONTENTSPREFACEPREFACE ... 1FEATURES ...

PRECAUTIONSDo not attempt to disassemble the unit. In order to prevent electrical shock, do not remove screw or covers. There are n

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS1. Power ON/OFF Button (POWER ON/OFF)Note:The DC power is supplied all the time from external DC

3. System Data Transmitting Indicator (SYS DATA TX)This indicator blinks irregularly for both PC-mode and Extension-mode while this unit s

7-1. PC-mode1. The numbers other than 1-5 on this switch are not used.2. Do not duplicate numbers with other WV-CU300/WJ-PC10.7-2. Extension-mode1,

1. RS-232C cableUse RS-232C standard cable (straight connection) of up to 49ft (15m) to connect between WJ-PCIO and other unit such

SETTING UP OF THE UNITRemove four screws fixing the top cover and remove top cover. There are switches and connectors on the board as