Panasonic PT-D3500U User Manual Page 44
- Page / 72
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
44
Replacing the lamp unit
Precautions on lamp unit replacement
Remove the power plug and confirm that the surroundings of the lamp unit have cooled off.
Be careful when handling a light source lamp. The lamp unit has high internal pressure. If improperly handled,
explosion might result.
A used lamp unit may burst if it is handled violently.
For disposition of used lamps, request an industrial waste disposal contractor.
Do not reset the cumulative time, except when the lamp unit has been replaced with a new unit.
If you continue to use a lamp after the replacement time, the lamp may break.
Philips screwdriver is necessary when replacing a lamp unit.
Take care not to slip your hand when using a screwdriver.
• A lamp unit is an optional part. Contact the dealer.
Replacement lamp unit model No.: ET-LAD35 (single bulb)
Rating: 300W
Long life lamp unit model No.: ET-LAD35L (single bulb)
Rating: 160W
• Other lamps than specified above cannot be used. Be sure to use the specified lamp.
Attention
Timing of lamp unit replacement
The lamp used for the light source has its due life. The life of light source lamp used in the main unit is 1 500
hours
1
(when lamp output is HIGH). However, it may happen that the lamp becomes dead (will not light) by the
time of 1 500 hours
1
depending on the characteristics of individual lamps and working conditions (lamps may
reduce their life affected by the times of lighting and the intervals between previous lighting and next lighting).
Therefore, it is strongly recommended for the user to keep a spare bulb.
If your lamp unit is not replaced after 1 300 hours
2
(with the lamp output set at “HIGH”), power supply will be
turned off automatically at the time of 1 500 hours
1
, entering a standby state. After 1 500 hours
1
of initial
lighting, power supply is turned off automatically about 10 minutes later, entering a standby state even if it is
turned on again.
Indication after 1 300 hours
2
(with the lamp output set at “HIGH”)
When lamp unit used hours have reached 1 300 hours
2
, lamp monitor
(LAMP) light up including standby state.
Further, an on-screen indication will appear for about 30 seconds as
shown in the diagram on the left, recommending replacement of lamp unit.
(The indication on the left diagram will disappear after about 30 seconds or
when either control button on the upper panel of main unit or remote
control button is operated.)
After the time of 1 500 hours
1
, the on-screen indication will not disappear
unless the menu (MENU) button is operated.
REPLACE LAMP
1 This time period is 4 000 hours when long life lamp units are used.
2 This time period is 3 800 hours when long life lamp units are used.
WARNING!
Replacement of the lamp unit should
only be carried out by a qualified
technician.
WARNING!
When replacing the lamp, allow it to
cool for at least one hour before
handling it.
- PT-D3500U 1
- Dear Panasonic Customer: 2
- IMPORTANT SAFETY NOTICE 2
- Contents 4
- Accessories 7
- Precautions on handling 8
- Name and function of parts 10
- Side-mounted 13
- Using the remote control unit 14
- Using a wired remote control 16
- Installation 17
- Connection 18
- Green(Connect Y) 19
- Red (Connect PR) 19
- Blue (Connect P 19
- Remove the lens 21
- Projection 22
- Powering off the projector 23
- Direct power off function 23
- How to adjust the lens 24
- Using the FREEZE function 25
- Using the SHUTTER function 25
- On-screen menus 27
- Adjusting the picture 29
- Adjusting the position 31
- How to use ADVANCED MENU 32
- Changing the display language 33
- Adjusting the audio 33
- OPTION1 settings 34
- OPTION2 settings 35
- Setting the security 37
- Setting the network 38
- Connecting the PC 38
- Using the serial terminals 39
- Using the REMOTE 2 terminal 41
- Indication of lamp monitor 42
- Procedure of cleaning 43
- Replacing the lamp unit 44
- Lamp unit replacement steps 45
- Using Web Browser Control 47
- Basic control page 48
- Monitor information page 49
- Detail control page 49
- Error information page 50
- E-mail setup page 51
- DNS server set up page 52
- POP server setup page 53
- Ping test page 53
- Contents of mail sent 54
- Adjust clock page 54
- Network config page 55
- Network status page 55
- Using the PJLink 56
- Before asking for service 57
- Specifications 58
- BPR input] 59
- BPR: 0.7 V[p-p] 75 Ω 59
- Compatible Signal List 60
- Dimensions 62
- Trademark Acknowledgement 63
- NOTES IMPORTANTES 64
- CONCERNANT LA SÉCURITÉ 64
- AVERTISSEMENT 65
- Attention 67
- Remplacement de la lampe 69
- INIT. COMPT 71
- INFORMATION SYSTÈME 71
Related products and manuals for Data projectors Panasonic PT-D3500U
Data projectors Panasonic PT-D9510U User Manual
(100 pages)
(100 pages)
© 2020, manymanuals.com. All rights reserved. | 1.636 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals