Panasonic WVBP550_SERIES Operations Instructions

CCTV CamerasWV-BPR550/WV-BPR554(Lens : option)Before attempting to connect or operate this product,please read these instructions completely.FRANÇAIS

-8-10.5 V DC ≤ VA − (R x 0.42 x L) ≤ 16 V DCL : Cable length (meter)R : Resistance of copper wire (Ω/meter)VA : DC output voltage of power supply un

-9-C. The maximum extensible coaxial cable lengthbetween the camera and the monitor is shownbelow.Video Cable1. It is recommended to use a monitor who

-10-Note:Use the cable that is described below for RS485site communication.• Shielded, two twisted pairs cable• Low impedance• Wire gauge size is thic

-11-SYSTEM CONNECTIONa) Single Camera Connection (RS485 Interface Model/Half Duplex)b) Daisy Chain Connection(RS485 Interface Model/Half Duplex)WV-BP

-12-Installation of Auto Iris Lens ConnectorInstall the lens connector (YFE4191J100) when using avideo drive ALC lens.The installation should be made

Caution for Mounting the LensThe lens mount should be a C-mount or CS-mount (1”-32UN) and the lens weight should be less than 450 g(0.99 lbs). If the

The following adjustment should be made by qualifiedservice personnel or system installers.1. Loosen the screws on the flange-back adjustingring.2. Tu

• Mounting from the bottomThis camera is designed to be mounted from thebottom, as shown below. The mounting hole is astandard photographic pan-head s

-16-1. Camera Setup MenuThis camera utilizes a user setup menu that is displayed on-screen.The setup menu contains various items that form a tree-type

-17-MotionDetectorON/OFFLens DriveSignalSelectionDC VideoSpecialmenuDetectionLevelAdjustmentDetectionMasking AreaSelectionUpsidedownAPGainPedest

CAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION: TO REDUCE THE RISK OF ELECTRICSHOCK, DO NOT REMOVE COVER (ORBACK), NO USER SERVICEABLE PARTSINSIDE.

-18-Left ButtonSet SwitchRight ButtonDown ButtonUp ButtonUp Button (): This button is used to move thecursor upwards. Use this button toselect an item

-19- ** CAM SET UP **CAMERA ID OFF ALC/ELC ALC SHUTTER ---AGC ONSENS UP OFFSYNC INTMOTION DET OFF LENS

-20- ** SPECIAL **UP SIDE DOWN OFFAP GAIN ...I...PEDESTAL .I... - +CAMERA RESET PUSH SWRET END• Editing the

-21-SETTING PROCEDURESUNIT NUMBERThis item is used to select the camera number that isused with RS485 communication.1. Move the cursor to the paramete

-22-X ON/X OFFThis item is used to select applying the flow control ornot.1. Move the cursor to the X ON/X OFF parameter.2. Select NOT USE (not apply

0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().,'":;&#!?= +-*/%$ÄÜÖÆÑÅ SPACE POSI RET END RESET ...-23-● CAMERA Se

-24-2. Move the pointer to the character to be edited bypressing or . Then move the cursor to thecharacter area and select a new character.3. Press

-25-2-1. ALC Mode with SUPER-D ONSuper Dynamic Function (SUPER-D)The important object in a scene is usually placed in thecenter of the monitor’s scree

-26-2. Move the cursor to MASK SET and press . The48 mask areas appear on the monitor screen. Thecursor is blinking in the top left corner of thescre

-27-4. Repeat step 1 to 3 to mask the desired area. Tocancel masking, move the cursor to that area andpress .5. After masking is completed, press fo

CONTENTSPREFACE ... 2FEATURES ...

-28-4. Gain Control Setting (AGC ON/OFF)You can set the gain (brightness level portion of animage) to automatic level adjustment (ON) or fixedlevel (O

-29-• When ON is selected for SUPER-D, the SENS UPSELECT function for the WV-CU254 or WV-CU300system controller does not work.Use the buttons on the s

-30-5. The VS gen-lock mode has its own menu for hori-zontal phase adjustments. When the cable lengthof the video output or the gen-lock input ischang

-31-7. Set the oscilloscope to the horizontal rate andexpand the horizontal sync portion on the oscillo-scope.8. Adjust the horizontal phase by pressi

-32-Notes:• When the “I” cursor reaches the “+” end, itjumps back to “–”. At the same time, COARSEis incremented by one step to enable a contin-uous a

-33-1. Move the cursor to the LENS DRIVE parameter.2. Select DC if you are using the auto iris lens thatrequires a DC drive signal.Select VIDEO if you

-34-9. Special Menu (SPECIAL)This menu lets you adjust and setup the video signal ofthe camera to meet your requirements.Move the cursor to RET on the

-35-When the camera is aimed at a bright light, such as aspotlight, or a surface that reflects bright light, smearor blooming may appear. Therefore, t

Pick-up Device: 752 (H) x 582 (V) pixels, Interline Transfer CCDScanning Area: 4.9 (H) x 3.6 (V) mm (Equivalent to scanning area of 1/3” pick-up tube)

-37-Power Source and WV-BPR550: 220 - 240 V AC 50 Hz, 6.3 WPower Consumption: WV-BPR554: 24 V AC 50 Hz, 6.3 W12 V DC, 690 mADimensions (without lens):

1. The following functions are built in.(1) Auto Light Control (ALC)/Electronic LightControl (ELC)(2) The SUPER-D function eliminates interferenceby s

N0898-0 YWV8QA5034AN Printed in JapanInprimé au JaponN 30Matsushita Electric Industrial Co., Ltd.Central P.O. Box 288, Osaka 530-91, Japan

1. Do not attempt to disassemble the camera.To prevent electric shock, do not remove screwsor covers.There are no user serviceable parts inside. Ask a

-4-SUPERDYNAMICWV-BPR550SUPERDYNAMICWV-BPR550Hi-Z G/L 75ΩVIDEO OUTPOWERRS485(A)(B)GND220V-240V~50HzGEN-LOCKVIDEO OUTPOWERGEN-LOCKAC 24VINDC 12VIN1

q Auto Iris Lens ConnectorThis connector is used to connect with the auto irislens by a 4-pin male connector that is supplied asa standard accessory (

!3 Video Output Connector (VIDEO OUT)This connector is used to connect with the VIDEOIN connector of the monitor.!4 Power Cord SocketThis socket is us

Copper wire #24 #22 #20 #18size (AWG) (0.22mm2) (0.33mm2) (0.52mm2) (0.83mm2)Resistance 0.078 0.050 0.030 0.018Ω/mResistance 0.026 0.017 0.010 0.006Ω/