Panasonic WVCS850_SERIES Operations Instructions

Before attempting to connect or operate this product,please read these instructions carefully and save this manual for future use.Model No. WV-CS850WV

10● AUTO PAN KEYThis setting assigns SEQ, SORT, AUTO PAN or PATROL (PLAY) to the AUTO key on the controller. Afterthis setting, the AUTO key performs

11(6) Password Lock ON/OFF (PASSWORD LOCK ON/OFF)This setting controls access to the PRIVACY ZONE to be free or limited. If PASSWORD LOCK ON isselecte

12Generally, when a light from the background is too strong such as a spotlight, all objects except themain object in the picture are displayed darker

13(7) White Balance (WHITE BAL)You can select one of two modes for white balance adjustment as follows:• ATW (Auto Tracing White Balance)In this mode,

14SETTING PROCEDURESThe following setting procedures are described on the assumption that this model is used in combinationwith the WJ-SX550A matrix s

15 Preset● Preset Menu Display1. Displaying the preset menu directly(1) Move the cursor to PRESET 1 and move the joystick to the leftor right to sele

163. Pan OffsetIf the camera is replaced with a new one, Pan Offset is used toadjust its positions to be the same as before.Preset position data is up

172. Press the CAM (SET) key to display the preset ID setting menu.To enter a new PRESET ID1. Move the cursor to the desired character using the joyst

18To set a display position for a PRESET ID1. Move the cursor to POSI and press the CAM (SET) key. Thedisplay position set menu appears.2. Using the j

19● Scene File Setting1. To set a scene file numberMove the cursor to SCENE FILE and select a scene file number (1to 10, or OFF) by moving the joystic

2The serial number of this product may be found on thetop of the unit.You should note the serial number of this unit in thespace provided and retain t

20 PRESET NO. 1*POSITION SETPRESET IDALC/MANUALDWELL TIMESCENE FILEPRESET SPEEDRET DELON ALC 10S1 ••••|••••L HPreset setting menu Deletin

21 Auto Mode Selection1. To set auto modeMove the cursor to AUTO MODE and select a mode by movingthe joystick to the left or right. Modes change as f

226. To set endless turn ON/OFFMove the cursor to ENDLESS, and move the joystick to the left orright to set endless turn ON or OFF.ON: The camera pans

23 SPECIAL 1● Privacy Zone ON/OFF (PRIVACY ZONE)Up to 8 unwanted zones can be masked on the monitor screen.1. Move the cursor to PRIVACY ZONE and the

243-3 Move the cursor to PUSH SET on the ZOOM/FOCUS, thenpress the CAM (SET) key.3-4 Adjust zoom and focus, then press the CAM (SET) key.3-5 Move the

25 ** SPECIAL1 **PRIVACY ZONE ON (DIS)PROPO. P/T OFFAREA TITLE ON (NESW)PATROL PLAYALARM IN/OUTPASSWORD LOCK ONCLEANING OF

26Setting [ON (USER)]If ON (USER) is selected on the SPECIAL1 menu, the Area Titleselection menu appears. The screen has the number column andtitle co

27● Patrol (PATROL)A routine of manual operations can be stored for up to 30 secondsand later reproduced repetitively.PATROL1. For PATROL LEARN, set t

28PATROL PLAY with a controller not having PATROL key1. Close the SET UP or SPECIAL1 menu. The camera turns to the starting point and the operationsst

29COAXIAL ALARM OUT Alarm output signals are supplied through the coaxial cable.1. Move the cursor to COAX and select ON or OFF.2. Press the CAM (SET)

3Panasonic presents highly advanced CCTV tech-nology that meets the demands of new and ever-changing applications.This high-performance combination co

30NEW PASSWORD4. To change the password in step 3-3 above, move the cursor fromOK to NEW PASSWORD then press the CAM (SET) key. NEWPASSWORD menu appea

31● Electric Zoom ON/OFF (EL-ZOOM ON/OFF)The electric zoom magnifies a scene tenfold. With a twenty-twofoldoptical zoom lens, the camera is capable of

32 Camera Setting1. To display the Camera Setting Menu• Move the cursor to CAMERA , and press the CAM (SET) key.The camera setting menu is displayed

33• The positioning of the CAMERA ID stops at the edges of thescreen.• The CAMERA ID moves faster when the joystick is keptpressed for more than 0.5 s

34BlinkingBlinkingBlinkingTurns to white(2) ALC Mode with SUPER-D2 OFF1. Move the cursor to the SUPER-D2 parameter and select OFF.(When you select MAN

35 ** SET UP **CAMERA IDALC/MANUALSHUTTERAGCSENS UPSYNCWHITE BALMOTION DETAF MODERET SPECIAL2 OFF ALC OFFONOFFINT ATW ON MANUAL S Camera

367. Synchronization Setting (SYNC)1. Display SET UP on the monitor screen.If necessary, refer to Setup Menu Display on page 14 for detailson displayi

Notes:• When the “|” cursor reaches the “+” end, it jumps back to “–”. At the same time, COARSE isincremented by one step to enable a continuous adjus

38 ** AWC **RBRET••••|••••- +••••|••••- +AWC fine adjustment menu ** SET UP **CAMERA IDALC/MANUALSHUTTERAGCSENS UPSYNCWHITE BAL

399. Motion Detector Setting (MOTION DET)1. Display SET UP on the monitor screen.(Refer to Setup Menu Display on page 14 for details on display-ing th

41. Do not attempt to disassemble the cam-era.To prevent electric shock, do not removescrews or covers.There are no user serviceable parts inside.Ask

40Important Notices:• The object of motion detection should meet the following conditions.1) It should be larger than 1/48 of the size of the picture

4111. Special 2 Menu (SPECIAL2)This menu lets you adjust and set up the picture quality to meet yourrequirements.• Display SET UP on the monitor scree

42 ** SPECIAL2 **CHROMA GAINAP GAINPEDESTALBWBURST(BW)REFRESHCAMERA RESETRET••••|••••••••|•••••|•••••••- + AUTO ON→PUSH SW→PUSH SW(4) BWMo

43 RS485 Set Up● Initial camera communication parametersIn an RS485 chain the matrix switcher, PC, controllers and cameras should be set to the same

44ALARM DATASpecifies alarm transmission mode depending on the protocol selected by the 8-bit DIP switch. Refer toINSTALLATION for protocol selection.

45• The following steps of installation and connection should be taken by qualified service personnel orsystem installers and should conform to all lo

46Unit numberSwitch 1, an 8-bit DIP switch, specifies unit number for three protocols: Panasonic’s new and conven-tional protocol and AD protocol.When

47For conventional Panasonic’s protocol1234ON5678Switch PositionUnitNumber1234ON56781234ON56781234ON56781234ON56781234ON56781234ON56781234ON56781234ON

481234ON5678Switch PositionUnitNumber1234ON56781234ON56781234ON56781234ON56781234ON56781234ON56781234ON56781234ON56781234ON56781234ON56781234ON5678123

49BP 2BP 1 FunctionSwitchPositionFunctionSwitchPositionRS485 SettingThe 4-bit DIP switch in used forRS485 termination and protocolselection.ONMarking1

5wertt*qyuoi!0(WV-CS850)(WV-CS854)y Camera Mounting Baseu Panning Start Pointi Fall Prevention Wireo Decoration Cover!0 Dome Coverq Alarm Input Connec

505. Tighten the fixing screw M3 (provided).Notes :(1) Tighten the camera fixing screw with ascrewdriver.(2) Follow the instructions given here toensu

How to assemble the cable with theaccessory connectorStrip back the cable jacket approx. 3 mm (0.1inch) and separate the individual conductors.Recomme

GreyWhitePinkYellow Green or Light BlueBlackBrownRedOrangeYellowLight Blue or GreenBluePurpleWire ColourWire Colour• RS485 connectionNote:Use the cabl

53CPURS-232CTIMEADJUST INCOMPRINTEROUT INVS/VDVDOUTOFF+9V+5V−5VPOWERON11A00001OUT IN1OUT IN2OUT IN3OUT IN4MONITORALARM OUTRESET OUTOUTPUTOUT

Power Source3.57 mm (H) x 2.67 mm (V), 1/4”737 (H) x 575 (V)DimensionsFocus SpeedEffective Pixels15.625 kHz54F1.6 - 22, CLOSEFocal LengthSUPER-D224 V

55AUTO FOCUSPanning RangeWeights and dimensions indicated are approximate.Specifications are subject to change without notice.360° EndlessPossible (in

56Selecting a PRESET position From #1 to #64#1 [1] + [CAM FUNC]#10 [1] + [0] + [CAM FUNC]#64 [6] + [4] + [CAM FUNC]AUTO PANON [6] + [5] + [CAM FUNC]OF

N0200-1030 YWV8QA5388BN Printed in JapanN 19 Gedruckt in JapanImprimé au JaponImpreso en Japón2000 © Matsushita Communication Industrial Co., Ltd. Al

6 Setup MenuSetup menus are shown in the diagram below. Various kinds of setup are available to have the camerafulfill your requirements. Menus are b

7ShutterSpeedSelectionAGCON/OFFSensitivityUpON/OFFWHITEBALAWC ATWSuper-D2OFFLight ControlALC/MANUALSuper-D2ONManualLevelAdjustment(Contrast)Manual

8The keys (switches) to use for setup are as shown in the table below. The joystick on the connected con-troller may also be used for setup. The tab

9 Setup Menu Description● PRESET(1) Position (POSITION SET)POSITION SET adjusts the camera picture by panning, tilting, zooming and focusing.See page