Panasonic WVCS650_SERIES Operations Instructions Page 1

Combination CameraWV-CS650WV-CS654WV-CSR650Before attempting to connect or operate this product, please read these instructions completelyENGLISHDEUTS

- 7 -● AUTO MODEAUTO MODE is for setting the movement of the camera. You can select from three automatic operationmodes and one manual operation mode

- 8 -Generally, when a light from the background is too strong such as a spotlight, all objects except themain object in the picture are displayed dar

- 9 -(7) White Balance (WHITE BAL)You can select one of two modes for white balance adjustment as follows:• ATW (Auto Tracing White Balance)In this mo

- 10 -SETTING PROCEDURESThe following setting procedures are described on the assumption that this model is used in combinationwith the WJ-SX550A matr

- 11 -● Changing the camera communication parameters1. Display the SET UP MENU. Move the cursor to COM. SET UP DISABLE and press the CAM (SET)key to

- 12 -CU550A.DELAY TIMESpecifies the time to transmit the acknowledge request when communicating on a two-line connection.(OFF, 10, 20, 40, 100 ms) T

- 13 -● Position Setting1. Move the cursor to POSITION SET and press the CAM (SET) key.The position set menu is displayed.2. To set panning/tilting po

- 14 -● Preset ID Setting1. Move the cursor to PRESET ID and move the joystick to the left orright to select ON or OFF.ON: Preset ID is displayed on t

- 15 -To delete an edited PRESET IDMove the cursor to RESET and press the CAM (SET) key. PRESET NO.15*H 0123456789 ABCDEFGHIJKLM NOPQRSTUV

- 16 -● Dwell Time Setting• Move the cursor to DWELL TIME and set a dwell time by movingthe joystick to the left or right. Dwell time changes as follo

The serial number of this product may be found on thetop of the unit.You should note the serial number of this unit in thespace provided and retain th

PRESET NO.15*HPOSITION SET PRESET ID ON ALC/MANUAL ALC DWELL TIME 2SSCENE FILE 1 RET DELPreset setting menu- 17 - Dele

- 18 - Auto Mode Setting1. To set auto modeMove the cursor to AUTO MODE and select a mode by movingthe joystick to the left or right. Modes change as

- 19 -5. To set endless turn ON/OFFMove the cursor to ENDLESS, and move the joystick to the left orright to set endless turn ON or OFF.ON: The camera

- 20 - Camera Setting1. To display the Camera Setting Menu• Move the cursor to CAMERA , and press the CAM (SET) key.The camera setting menu is displ

- 21 -• The positioning of the CAMERA ID stops at the edges of thescreen.• The CAMERA ID moves faster when the joystick is keptpressed for more than 0

- 22 -BlinkingBlinkingBlinkingTurns to white(2) ALC Mode with SUPER-D OFF1. Move the cursor to the SUPER-D parameter and select OFF.(When you select M

- 23 - ** SET UP **CAMERA ID OFF ALC/MANUAL ALC SHUTTER OFFAGC ONSENS UP OFFSYNC LL WHITE BAL ATW MOTION DET

- 24 -7. Synchronization Setting (SYNC)1. Display SET UP on the monitor screen.If necessary, refer to Setup Menu Display on page 10 for detailson disp

- 25 -Notes:• When the “|” cursor reaches the “+” end, it jumps back to “–”. At the same time, COARSE isincremented by one step to enable a continuou

- 26 - ** AWC ** R ...I... − +B ...I... − +

IMPORTANT! / WICHTIG! / IMPORTANT! Do not install the camera near the airoutlet of an air conditioner.The lens may become cloudy due to condensa-tion

- 27 -9. Motion Detector Setting (MOTION DET)1. Display SET UP on the monitor screen.(Refer to Setup Menu Display on page 10 for details ondisplaying

- 28 -Important Notices:• The object of motion detection should meet the following conditions.1) It should be larger than 1/48 of the size of the pict

- 29 -11.Special Menu (SPECIAL)This menu lets you adjust and set up the video signal of the camerato meet your requirements.• Display SET UP on the mo

- 30 - ** SPECIAL **CHROMA GAIN ...I...AP GAIN ...I...PEDESTAL .I... – + UP SIDE DOWN OF

Initialization of soft-ware communica-tion parameters- 31 -Precaution:The following installations should be made byqualified service personnel or syst

- 32 -1. Remove the mounting screw (M3) from thecamera mounting angle (provided).2. Mark the mounting holes on the ceiling,using the removed camera mo

- 33 -5. Mount the camera on the camera mountingangle and rotate the camera clockwise.2. Follow the instructions given here toensure that the camera a

How to assemble the cable with theaccessory connectorStrip back the cable jacket approx. 3 mm (0.1inch) and separate the individual conductors.Recomme

- 35 -● RS485 site connectionFor daisy chain connection of multiple cameras, make sure to match each male connector with its femalecounterpart.Note:Us

- 36 -CPURS-232CTIMEADJUST INCOMPRINTEROUT INVS/VDVDOUTOFF+9V+5V−5VPOWERON11A00001OUT IN1OUT IN2OUT IN3OUT IN4MONITORALARM OUTRESET OUTOUTPU

ENGLISH- 1 -CONTENTSPREFACE ... 1FEATURES ...

WV-CS650 and WV-CSR650 220 - 240 V AC, 50 HzWV-CS654 24 V AC, 50 HzPower Source1/3”F1.2 - 64, CLOSEFocal LengthSUPER-D130 (D) x 191 (H) mm (5-1/8”

Panning RangeWeights and dimensions indicated are approximate.Specifications are subject to change without notice.360° EndlessPossible (in Auto-Pan mo

Matsushita Electric Industrial Co., Ltd.Central P.O. Box 288, Osaka 530-91, JapanN0798-0 YWV8QA4984AN Printed in JapanN 30 Gedruckt in JapanImprimé au

- 2 -1. Do not attempt to disassemble thecamera.To prevent electric shock, do not removescrews or covers.There are no user serviceable parts inside.As

- 3 -wqee*rtyuio(6) Fall Prevention Wire(7) Decoration Cover(8) Cooling Holes(9) Dome Cover(1) Data Cable (only for WV-CSR650)(2) Video Output Connect

- 4 -Dwell TimeSettingScene FileSettingCamera IDDisplayPositionPreset IDDisplayPositionSuper-DONShutterSpeedON/OFFAGCON/OFFPresetSettingMenuPositionNo

• WV-RM70(available with all models except WV-CSR650)Up Switch: Moves the cursor upwards.Down Switch: Moves the cursor downwards.Right Switch: Moves t

Setup Menu Description● RS485 site communication (only WV-CSR650)Communication parameters• Full/Half duplex (page 31)• Transmission speed (2 400 - 1