Model No. AG-CPD20POperating InstructionsS0909K0 -MPrinted in JapanENGLISHVQT2C58Memory Card Video RecorderBefore operating this product, please read
10Notes on Handling Usage• Do not remove an SDHC Memory Card while it is being accessed, as the SDHC Memory Card may be damaged or the SDHC Memory C
11Control Reference GuideFront panel (1) REC button ( )Starts recording of video and sound to an SDHC Memory Card. STOP button ( )Stops recording. SD
12Control Reference Guide (continued)Front panel (2) USB connectorA commercially available USB memory device can be connected for use as external memo
13Control Reference Guide (continued)Rear panel (1) CAMERA 1 connectorConnect the separately sold Color Camera using the cable attached to the Camera
14Control Reference Guide (continued)Rear panel (2) AUDIO IN 1 (black), 2 (red), 3 (black), and 4 (black) connectors (Pin jack)These are line or micr
15Mounting bracketThe recorder can be mounted turned by 90° in a center console or trunk. The figure below is an example of mounting in a center conso
16Connections• Connect the power cable when all connections are completed. Be sure to read the instructions in the connector diagram on pages 21 thro
17Connections (continued): Connect to a terminal that always supplies power through a fuse, regardless of whether the engine is on or off.: Connect th
18Notes:• Do not try to turn the key further than the stop position, and do not move it unnecessarily, to prevent damage to the key and lock.• To pr
19(4) Remove the key.Turn the key counterclockwise to [ ], and remove it.SDHC Memory Card Insertion and Removal (continued)Removing an SDHC Memory C
2WARNING:• To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture.• To reduce the risk of fire or electric s
20Turning the Recorder On and OffRecorder power is supplied from the vehicle’s battery.OnOffTurn the vehicle’s ignition switch to ON or ACC.Power to t
21Connector Signals∗ Recorder power can be turned on and off by the SIGNAL port. If an OFF signal is input while the recorder is operating, the recor
22Connector signals (continued)[GPIO] connector (female)Pin numberSignalCable color1 GND Black/White2 N.C. ―3 GPI 13 Pink4 GPI 14 Light Green5 GPI 15
23Connector signals (continued)[CONTROL PANEL] connector (male)Pin numberSignal1 N.C.2 N.C.3 DC_IN4 GND (DC_IN)5 SOUT_P6 SOUT_N7 SIN_P8 SIN_N9 GND (DI
24Power requirements: 12 V DC / 24 V DCInput current: 2.7 A (at 12 V DC) 1.3 A (at 24 V DC)Current consumption in standby
25Specifications (continued) VideoInputs:CAMERA 1 x 1 1.0 V [P-P], 75 Ω, unbalancedCAMERA 2-6 (Pin jack) x 5 1.0 V [P-P], 75 Ω, unbalancedOutputs:
26Section 1: Limited Warranty - HardwarePanasonic Computer Solutions Company (referred to as "Panasonic") will repair the products listed be
27MEMO
Panasonic Computer Solutions CompanyPanasonic Computer Solutions Company50 Meadowlands Parkway, Panazip 2F-5,Secaucus, NJ 07094© 2009P
Read this first! (continued) indicates safety information.CAUTION:In order to maintain adequate ventilation, do not install or place this unit in a bo
4IMPORTANT SAFETY INSTRUCTIONS(1) Read these instructions.(2) Keep these instructions.(3) Heed all warnings.(4) Follow all instructions.(5) Do not use
5Contents5SDHC Memory Card Insertion and Removal...18 Inserting an SDHC Memory Card ...18 Removing an SDHC Me
Wireless LAN (commercially available)6Functions of This RecorderAn AG-CPD20P is a vehicle video recorder using SDHC Memory Cards. A separately sold vi
7Key ...2 Remote Control Panel (AG-RCP30P) Color Camera (AG-CK10P) Cable Kit (AG-CR13P)P
8Before Use• In no event will Panasonic be liable for any damages, including any incidental or consequential damages, stemming from a failure to reco
9Before Use (continued) About the Internal ClockConfirming the TimeThe internal clock is set at the time of factory default. Check the time before usi
Comments to this Manuals