Panasonic PT-D6000ULS User Manual download pdf (Page 29)

PROJECTOR SETUP menu

ENGLISH - 29

Settings

You can select a lamp lighting pattern for using environment.

Press I H to cycle through options, and the ENTER button.

If using the projector for a continuous period of 24 hours or

more, this setting can be used to automatically switch the

lamps that are turned on in order to reduce the lamp

deterioration that can occur as a result of continuous use.

The luminance of the projection lamp can be changed

depending on user’s needs or the viewing conditions.

You can select the electrical consumption while in standby

mode.

This sets the communication parameters at the serial

terminals.

You can customise the REMOTE 2 IN terminal function.

DEFAULT The pin assignment of the REMOTE 2 IN

terminal is used as the projector default

setting.

USER For changing an optional input module or

customising the pin assignments.

LAMP SELECT

DUAL All lamps will light.

SINGLE

Selects a lamp with shorter duration of

use.

LAMP1 Selects the Lamp unit 1.

LAMP2 Selects the Lamp unit 2.

NOTE:

• If, in the SINGLE, LAMP1 or LAMP2 mode, one lamp remains

off or the currently active lamp exceeds 2 000 hours of

cumulative operating time (when HIGH is selected as the

LAMP POWER setting), the other lamp will light. If, in the

DUAL mode, one lamp remains off or the currently active lamp

exceeds 2 000 hours of cumulative operating time (when

HIGH is selected as the LAMP POWER setting), the other

lamp alone will light. However, if both lamps remain off or the

2 000 hours of cumulative operating time (when HIGH is

selected as the LAMP POWER setting) are exceeded, the

projector will enter the standby mode.

• The colours of the items indicate the status.

Green: Current setting

Yellow: Current setting (when a lamp fails or fails to light)

Red: Lamp that has failed to light

White: Any other status.

• If the projector is repeatedly used for short periods of time, the

lamps will need to be replaced more frequently.

LAMP RELAY

OFF Deactive

00:00 - 23:00 1 hour interval from 00:00 to 23:00

NOTE:

• Only when DUAL or SINGLE is selected in LAMP SELECT,

LAMP RELAY is available. If LAMP1 or LAMP2 is selected,

LAMP RELAY function is not available.

LAMP SELECT

setting

Repeated operation

SINGLE

LAMP1 and LAMP2 light alternately by the

set time, and the shorter duration of use

lamp will light first.

DUAL

After both lamps light for the set time, only

one lamp is turned off for 2 hours, then for

only the other lamp for next 2 hours. The

longer duration of use lamp will be turned off

first.

LAMP POWER

HIGH Set when high brightness is necessary.

LOW

Set when high brightness is not

necessary.

NOTE:

• When set to LOW, it is possible to reduce power consumption,

reduce operating noise and extend lamp service life.

STANDBY MODE

NORMAL

The electrical consumption in standby

mode is 10 W.

ECO

The electrical consumption in standby

mode is 0.5 W.

NOTE:

•With ECO setting, NETWORK function, RS-232C output and

some of RS-232C commands are not available. When switch

on the projector, projection will start about 10 seconds late.

RS-232C

(IN) BAUDRATE Select 9600, 19200 or 38400.

(IN) PARITY Select NONE, EVEN or ODD.

(OUT) BAUDRATE Select 9600, 19200 or 38400.

(OUT) PARITY Select NONE, EVEN or ODD.

RESPONSE(ID ALL) Select ON or OFF.

GROUP Select A to Z.

RESPONSE(ID GROUP) Select ON or OFF.

REMOTE2 MODE

PIN1 GND

PIN2 POWER H NONE

PIN3 - PIN7

RGB1 H RGB2 H VIDEO H S-VIDEO H DVI-

D H BALLAST VERSION H REWIND ALL

FILTER H NONE

PIN8 SHUTTER H NONE

PIN9 ENABLE H DISABLE

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 51 52

Comments to this Manuals

No comments

Panasonic PT-D6000ULS User Manual Page 29

Comments to this Manuals

Related products and manuals for Data projectors Panasonic PT-D6000ULS