Panasonic WV-SF538 Installation Guide

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.The model number is

10PrecautionsRefer installation work to the dealer. Installation work requires technique and experi-ences. Failure to observe this may cause fire, ele

11[Precautions for use]This product is designed to be used indoors. This product is not operable outdoors. This product has no power switch. When turn

12Code labelThe code labels (accessory) are required at inquiry for trouble. Use caution not to lose these labels. It is recommended to paste one of t

13Precautions for InstallationPanasonic assumes no responsibility for injuries or property damage resulting from fail-ures arising out of improper ins

14Screw tightening • The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the insta

Major operating controls * This connector is provided only for service. Do not use the connector for checking the adjust-ment of the angular field o

16<Side view>About the [INITIAL SET] buttonAfter turning off the power of the camera, turn on the power of the camera while holding down this bu

17Detaching the dome coverz Loosen the dome cover fixing screws using the bit for tamperproof screw (accessory).Note: • The dome cover and the came

18z Remove the dome cover fixing screw (M3, step screw, x1). x Rotate the dome cover counterclockwise two steps, and align the indication "OPEN&q

19PreparationsWhen installing the camera on a wall or a ceiling, there are four methods as specified below. (☞ Pages 20 and 21) • Using the two-gang

2WARNING:• To prevent injury, this apparatus must be securely attached to the floor/wall/ceiling in accordance with the installation instructions.•

20Using the side cable access holeWhen installing the camera directly on the ceiling or wall with cables exposed, cut out a portion of the dome cover

21Installing the camera directly on the ceiling or wallPlace the installation template label (accessory) on the ceiling or wall, and make a hole to pa

22Insert/remove an SD memory card (WV-SF549/WV-SF539 only)IMPORTANT: • When inserting an SD memory card, make sure the direction. • Before removi

23ConnectionBefore starting the connection, turn off the power of this camera and the devices to be connected. Check and prepare the required devices

24c Connect an external speaker with amplifier to the audio output connector (for use of the audio transmission function). SF549 SF539 Connect a ster

25 e After the cable connection, connect the exter-nal I/O terminal plug to the external I/O termi-nals of the camera. IMPORTANT: • Do not connec

26When using 12 V DC power supply* q Loosen the screws of the power cord plug (accessory). w Connect the cable of the 12 V DC power sup-ply* to the

27When using PoE (IEEE802.3af compliant)Connect a LAN cable (category 5 or better, straight, STP*) between a PoE device (such as a hub) and the networ

28Connection example when connecting to a network using a PoE hubPoE device (hub)PCMicrophone (option)Microphone (option)6SHDNHUZLWKDPSOLƄHU(option

29InstallationCamera mountingInstallation shall be conducted after turning off each device. z Detach the dome cover. (☞ Page 17)x Connect the cables

ContentsImportant safety instructions ... 4Limit

30Adjustmentz Adjust the camera angle. When determining the camera angle, repeat fine adjustments by gradually moving the panning table, tilting table

31Vertical position (Tilting)Loosen the tilting lock screws (x2), and rotate the tilting table to adjust the tilting direction. (Adjustable range: ±75

32x Adjust the angular field of view and the focus. Adjust the angular field of view in accordance with the distance between the camera lens and a

33Note: • If the zoom lock knob is fully turned in the "W" direction, the periphery may become dark. In such a case, turn the zoom lock kn

34Attaching the dome coverFRONT TOPMONITOROUTLOCKAuto focus (AF)buttonAttach the dome cover to the camera. SF549 SF548The following procedure is requi

35z Align the indication "OPEN" to the marker of the camera to attach the dome cover. x Remove the cover film from the dome cover except the

36v Rotate the dome cover clockwise to adjustthe marker to "LOCK". b Fix the dome cover and the camera with the dome cover fixing screw (M3

37Configure the network settingsConfiguring the camera so that it can be accessed from a PCThe following are descriptions for when the camera with def

38c Select the camera you want to configure, and click [Access Camera].Note: • When cameras are displayed in [Panasonic IP Setting] screen, click th

39TroubleshootingBefore asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after

4Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5)

40Specifications• BasicPower source: 12 V DC, PoE (IEEE802.3af compliant)Power consumption:SF549 SF53912 V DC*: 530 mA, PoE 48 V: 120 mA (Class 2 devi

41Finish:SF549 SF548Main body: Aluminum die cast, sail whiteDome section: Clear polycarbonate resinSF539 SF538Main body: ABS resin, sail whiteDome sec

42Video analytics Face detection*1: On/Off (with the XML notification setting)Privacy zone: Gray/Off (up to 2 zones available)VIQS: On/O

43Image compression method*1: H.264 Image quality: Low/ Normal/ Fine Transmission type: Unicast/Multicast Bit rate: Constant bit rate/Best effo

44Multi-screen: Up to 16 camera images can be displayed simultaneously on amulti-screen. (Including the camera itself)Compatible SDXC/SDHC/ SD memory

45Standard accessoriesOptional accessoriesInstallation Guide (this document) ... 1 setWarranty card ...

46

47

Information for Users on Collection and Disposal of Old Equipment and used BatteriesThese symbols on the products, packaging, and/or accompanying docu

Limitation of liabilityTHIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMIT

6The network cameras WV-SF549/WV-SF548/WV-SF539/WV-SF538 are designed to operate using a PC on a network (10BASE-T/100BASE-TX). By connecting to a net

7About the user manualsThere are 2 sets of operating instructions for the WV-SF549, WV-SF548, WV-SF539, WV-SF538 as follows. • Installation Guide:

8Note: • For further information about PC system requirements and precautions for when using Microsoft Windows 7, Microsoft Windows Vista, or Windows

9Network securityAs you will use this unit connected to a network, your attention is called to the following security risks. q Leakage or theft of i