Panasonic PTD7700U Operations Instructions Page 59
- Page / 116
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
59
Some size modes are not available for certain types of input signals.
• For RGB1 and RGB2 input signals: VID AUTO, S1 AUTO or VID AUTO (PRIORITY) cannot be selected.
• For VIDEO input signals: DEFAULT, S1 AUTO or VID AUTO (PRIORITY) cannot be selected.
• For an NTSC signal with VIDEO or S-VIDEO input: DEFAULT cannot be selected.
Note
Size modes
• DEFAULT: Pictures are displayed without changing the aspect ratio of the input signals.
• THROUGH: Pictures are displayed without changing the resolution of the input signals.
• ZOOM: Pictures can be displayed in various magnifications. The user can magnify the pictures with the
magnification ranging from 50% to 999%, and the fiducial point is set on the top left of the screen.
• 16:9 (D7700U only): Pictures are displayed in the aspect ratio of 16:9.
• 4:3 (DW7000U only): Pictures are displayed in the aspect ratio of 4:3.
• S4:3 (D7700U only): Pictures are scaled down to 75% of the original size without changing the aspect ratio of the
input signals. This mode is used when projecting the 4:3 pictures on the 16:9 screen.
• H FIT (DW7000U only): Pictures are displayed using all the panel pixels in the horizontal direction.
Signals with an aspect ratio where the pictures are taller than with a ratio of 16:9 will be
displayed with their bottom areas cut off.
• HV FIT: Pictures are displayed on the whole panel pixels.
If the aspect ratio of the input signals is different from that of the panel, the pictures are displayed by
converting it into the panels aspect ratio (4:3 for PT-D7700U and 16:9 for PT-DW7000U).
• VID AUTO: The projector identifies the video ID (VID) embedded in the picture signals and displays the picture by
automatically switching the screen sizes between 4:3 and 16:9.
This function is effective for the video and S-video input.
• S1 AUTO: The projector identifies the S1 signal and displays the picture by automatically switching the screen
sizes between 4:3 and 16:9.
This function is effective for the S-video input.
• VID AUTO (PRIORITY): The projector identifies the abovementioned VID or S1 signals and displays the picture
by automatically choosing the screen sizes of 4:3 or 16:9 according to the VID if it is
detected or S1 signals if a VID is not detected.
This function is effective for the S-video input.
POSITION
SHIFT
SIZE DEFAULT
CLOCK PHASE 0
KEYSTONE
Press the “MENU” button.
The MAIN MENU screen will be displayed
Select the “POSITION” with the
buttons.
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
LANGUAGE
OPTION
Press the “ENTER” button.
The POSITION screen will be displayed
Select “CLOCK PHASE” with the
buttons.
Adjust the clock phase with the
buttons.
The value changes from 0 to 31.
Clock phase adjustment
Clock phase adjustment achieves the best image when the screen flickers or halo is observed around the contour.
Procedure of adjustment
• No optimal value may be obtained if the output of the PC to which the signal input is applied is unstable.
• No optimal value may be obtained if the total number of dots is not correct.
• The clock phase can be adjusted only when RGB signal input is applied with RGB1, RGB2 IN, and the
analog input module (optional: ET-MD95RGB).
Note
- PT-D7700U 1
- PT-DW7000U 1
- Dear Panasonic Customer: 2
- IMPORTANT SAFETY NOTICE 2
- Contents 4
- Accessories 7
- Precautions on handling 8
- Examples of system expansion 9
- Name and function of parts 10
- Projector 11
- Using the remote control unit 15
- Installation 18
- (optional) (continuing) 20
- Connection 24
- Blue (connected to P 25
- terminal) 25
- Installing the input module 28
- Procedure of installation 29
- Remove the slot cover 29
- Insert the input module 29
- Fix the input module 29
- Register the input signal 29
- ET-MD95RGB 31
- ET-MD95VM2 32
- SERIAL 34
- HD SERIAL 36
- DVI-D IN DVI-D OUT 37
- How to install the 38
- How to remove the 38
- Projection 39
- Powering off the projector 40
- How to adjust the lens 41
- Registration of new data 44
- Sub memory 46
- Using the FREEZE function 48
- Using the SHUTTER function 48
- On-screen menus 49
- Adjusting the picture 51
- DYNAMIC IRIS setting 54
- Adjusting the position 57
- Size adjustment 58
- Clock phase adjustment 59
- How to use ADVANCED MENU 61
- Blanking adjustment 62
- Adjusting the clamp position 64
- Edge blending adjustment 65
- Raster position 67
- How to use RGB REALITY mode 70
- Option settings 71
- Installation Setting 72
- Lamp select 73
- Lamp power 73
- Adjusting color matching 75
- Automatic adjustment 77
- Video setting 77
- Fan control 78
- Output resolution 78
- (D7700U only) 78
- Auto signal 78
- Setting FUNC1 80
- Password 80
- Using the serial terminals 82
- Control commands 83
- Cable specifications 83
- Using the REMOTE 2 terminal 84
- RS-422 control functions 85
- Setting the security 86
- Changing the password 87
- Setting the text 87
- Changing the text 87
- How to use CP OPTION 88
- Setting the system format 89
- Example of connection 90
- Top page 93
- Network setting page 93
- Advanced control page 94
- Monitor information page 95
- E-mail setting page 95
- TEMP LAMP1 LAMP2 98
- Procedure of cleaning 99
- Replacement of lamp unit 100
- Before asking for service … 103
- Specifications 104
- R input] 105
- BPR: 0.7 V[p-p] 75 Ω 105
- Appendix 106
- Outside dimensions 107
- NOTES IMPORTANTES 108
- CONCERNANT LA SÉCURITÉ 108
- AVERTISSEMENT 109
- Attention 110
- Remplacement de la lampe 113
- M0704-1104 116
Related products and manuals for Data projectors Panasonic PTD7700U
(68 pages)
(56 pages)
(122 pages)
(55 pages)
(124 pages)
(48 pages)
(112 pages)
(52 pages)© 2020, manymanuals.com. All rights reserved. | 3.230 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals