Panasonic DMRE80H Operations Instructions download pdf (Page 4)

RQT6984

Setting up

STEP 2 The remote control

≥Insert so the poles (i and j) match those in the remote control.

≥Do not use rechargeable type batteries.

Do not:

≥mix old and new batteries.

≥use different types at the same time.

≥heat or expose to flame.

≥take apart or short circuit.

≥attempt to recharge alkaline or manganese batteries.

≥use batteries if the covering has been peeled off.

Mishandling of batteries can cause electrolyte leakage which can

damage items the fluid contacts and may cause a fire.

Remove if the remote control is not going to be used for a long

period of time. Store in a cool, dark place.

[Note]

If you cannot operate the unit or television using the remote control

after changing the batteries, please re-enter the codes (television

➜page 9, main unit ➜page 46).

After plugging the unit into your household AC outlet and pressing

[Í, DVD POWER] to turn the unit on for the first time, the unit

assists you to set the menu language, and automatically tunes in all

the channels it can receive and sets the clock.

The unit automatically determines the type of transmission (air or

cable) and puts them into channels as follows.

Batteries

Use

R6/LR6, AA, UM-3

Opening the rear cover.

Press with your

finger

Closing the rear cover.

Slide into place.

When the cover

comes off

Remote control signal sensor

7 m (23 feet) directly in front of the unit

30x

20x

Band Channel

TV Mode

(Air)

VHF 2s13

UHF 14s69

CATV Mode

(Cable)

VHF 2s13

CATV LOW BAND 95s99

CATV MID/SUPER BAND 14s36

CATV HYPER BAND 37s65

ULTRA BAND

66s94

100s125

SPECIAL CATV CHANNEL 1

DVD

INPUT SELECT

VCR Plus+

OPEN/CLOSE

TV/VIDEO

VOLUME

SKIP

DIRECT NAVIGATOR

PLAY LIST

TOP MENU

ENTER

FUNCTIONS

RETURN

STOP

PAU S E

PLAY/x1.3

SLOW/SEARCH

CANCEL

123

DVD TV

789

100

FRAME

CM SKIP TIME SLIP

ERASE

REC

PROG/CHECK

ADD/DLT

DUBBING

REC MODE

STATUS

MARKER

AUDIO

SETUP

DISPLAY

POSITION

MEMORY

POWER

Í, DVD POWER

3, 4, 2, 1

ENTER

ADD/DLT

W, X, CH

RETURN

SETUP

HDD DVD

Numbered

buttons

REC

HDD

DVD

REC

POWER, Í/I

X,W, CH

STEP 3 Plug-in Auto Tuning

RQT6984

Setting up

Preparation

≥Confirm that the antenna is connected correctly.

≥Turn on the television and select the appropriate video input to

suit the connections to this unit.

1 Press [Í, DVD POWER] to turn the

unit on.

2 Press [3, 4] to select the menu lan-

guage and press [ENTER].

e.g., when you select

English

3 Press [ENTER].

Plug-in Auto Tuning starts and the unit puts the stations it

can receive into channels.

The unit then proceeds with Auto Clock Setting. The time is

displayed when finished. If the clock is an hour slower or

faster than the actual time, go to “Time Zone Adjust” to cor-

rect it (➜page 47).

4 When the display shows the correct time

Press [ENTER] to complete Plug-in

Auto Tuning.

If the unit couldn’t set the clock automatically

Press [ENTER] to show the “Manual Clock Setting” screen. Set the

time manually (➜page 47).

To start Plug-in Auto Tuning again (after reloca-

tion, for example)

When the unit is on and stopped

1 Press and hold [X, CH] and [W, CH] on the main unit for

about five seconds.

The unit turns off.

2 Press [Í, DVD POWER] to turn the unit on.

Follow the above steps 2–4.

1 Press [SETUP] to show the menus.

Press [3, 4] to select “Channel” and

press [1].

3 Press [3, 4] to select “Antenna Sys-

tem” and press [ENTER].

4 Press [3, 4] to select “TV” or

“CATV” and press [ENTER].

The screen shown in step 2 reappears.

5 Press [3, 4] to select “Auto Channel

Setting” and press [ENTER].

If you have not yet set clock, the “Auto Channel/Clock Set-

ting” screen appears.

6 Press [ENTER].

Auto setting starts. This takes a few minutes. (To stop auto

channel setting, press [RETURN].) When finished, the Com-

plete screen or time display is shown. Press [ENTER].

To return to the previous screen

Press [RETURN].

When you are finished

Press [SETUP].

Add or delete channels if necessary channels are not set or unnec-

essary channels are set.

While this unit is receiving the antenna signal (but not during

recording):

1 Press the numbered buttons to select

a channel.

e.g., “5”: [0] ➜ [5]

“15”: [1] ➜ [5]

“115”: [100] ➜ [1] ➜ [5]

≥You can also use [W, X, CH]

when you are going to delete a channel.

2 Press [ADD/DLT].

The channel is deleted if it was set or added if it was not set.

e.g.,

Repeat steps 1 and 2 as necessary.

Antenna system, channel caption, and VCR Plusr guide

channel settings all revert to the default values when you

perform the procedure below. Timer recording settings are

also cleared.

If Plug-in Auto Tuning fails

English

Español

Français

Press ENTER

Pulse ENTER

Appuyer sur ENTER

Select Language

Seleccione la Lengua

Sélection de Langue

RETURN

ENTER

Auto Channel/Clock Setting

Connect antenna cable and if you use a

cable box, tune it to your local PBS CH

then. . .

Please push the ENTER key.

TAB

SELECT

Antenna System

Auto Channel Setting

Channel Caption

Preset Channel Caption

Manual Channel Caption

VCR Plusi CH Setting

CATV

Channel

SETUP

RETURN

Set Up

Disc

Video

Audio

Display

TV Screen

Adding and deleting channels

Antenna System

Auto Channel Setting

Channel Caption

Preset Channel Caption

Manual Channel Caption

CATV

Set Up

Disc

Channel

SETUP

Set Up

Channel

Antenna System

CATV

SETUP

Set Up

Disc

Video

Audio

Display

Channel

Auto Channel Setting

Connect antenna cable and if you use a

cable box, tune it to your local PBS CH

then...

Please push the ENTER key.

Unit’s display

CHANNEL 15 DELETED

1 2 3 4 5 6 7 8 9 ... 32 33

Comments to this Manuals

No comments

Panasonic DMRE80H Operations Instructions Page 4

Comments to this Manuals

Related products and manuals for DVD players Panasonic DMRE80H