Panasonic DMREX99V Operations Instructions download pdf (Page 88)

VQT2J46

Troubleshooting guide

Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chart

do not solve the problem, consult your dealer for instructions.

No power.

The unit does not turn on pressing [Í].

¾ Insert the AC mains lead securely into a known active

household mains socket. (> 10, 83)

¾ Linked timer recordings with external equipment is in recording

standby (“EXT-L” on the unit’s display blinks when [Í] is

pressed). Press [EXT LINK] to cancel the recording standby.

(> 30)

The unit switches to standby mode.

¾ One of the unit’s safety devices is activated. Press [Í/I] on the

main unit to turn the unit on.

The power is turned off automatically.

¾ If you connected this unit to a “HDAVI Control” compatible TV

with an HDMI cable, or connected this unit to a Q Link-

compatible TV with a fully wired 21-pin Scart cable, this unit will

be automatically set to standby mode when the TV is set to

standby mode. (> 46)

This unit turns off when the TV input is switched.

¾ This is a normal phenomenon when using VIERA Link (HDAVI

Control 4 or later). For details please read the operating

instructions for the TV.

The display is dim.

¾ Change “Unit’s Display” in the Setup menu. (> 76)

“0:00” is flashing on the unit’s display.

¾ Set the clock. (> 78)

The time recorded on the disc and the available

time shown do not add up.

The displayed time of this unit is different from

the actual recording time or MP3/WMA recording

time.

¾ Times shown may disagree with actual times.

¾ Available recording space on DVD-RW (DVD-Video format) or

+RW increases only when the last recorded title is deleted. It

does not increase if other titles are deleted.

¾ Even if you delete recorded content from the DVD-R, DVD-R

DL, +R or +R DL, there is no increase in disc space.

¾ More disc space than the actual recording time is used after

recording or editing the DVD-R, DVD-R DL, +R or +R DL 200

times or more.

¾ While searching, the elapsed time may not display correctly.

The clock is not correct.

¾ Under adverse reception conditions, etc., the automatic time

correction function may not work. In this case, “Automatic” is

automatically turned to “Off”. If re-setting the Auto Clock Setting

does not work, set the time manually. (> 78)

Compared to the actual recorded time, the

elapsed time displayed is less.

(Only when recording in NTSC)

¾ The displayed recording/play time is converted from the

number of frames at 29.97 frames (equal to 0.999 seconds) to

1 second. There will be a slight difference between the time

displayed and the actual elapsed time (e.g., actual 1 hour

elapsed time may display as approximately 59 minutes

56 seconds). This does not affect the recording.

The tape counter is not changing.

¾ The tape counter does not change while playing unrecorded

parts. The “second” display changes as follows:

(e.g., Blank after 1 h 36 min.)

¾ The unit’s display also appears like this if the tape is dirty or

damaged. Consult your dealer if this is the case.

“U88” is displayed and the disc cannot be

ejected.

¾ The unit is carrying out the recovery process. Do the following

to eject the disc.

1 Press [Í/I] on the main unit to switch the unit to standby.

If the unit doesn’t switch to standby, press and hold [Í/I] on

the main unit for about 3 seconds. The unit is forcibly

switched to standby.

While the unit is off, press and hold [

∫

] and [CH

]

on the main

unit at the same time for about 5 seconds. Remove the disc.

Television reception worsens or becomes

impossible after connecting the unit.

¾ This can occur because the signals are being divided between

the unit and other equipment. It can be solved by using a signal

booster, available from audio-visual suppliers. If it is not solved

by using a signal booster, consult the dealer.

¾ Broadcast signals may not be output from this unit’s RF OUT

terminal. Select “On” in “RF OUT ( Aerial Signal )” in the Setup

menu. (> 79)

The digital channel information or control panel

does not appear.

Status messages do not appear.

¾ Select the length of time (3–10 sec.) in the “On-Screen

Messages” in the Setup menu. (> 76)

¾ The digital channel information will not appear during playback

or recording.

¾ Analogue broadcasts do not support the digital channel

information.

¾ The control panel is only displayed when connected to a TV

supporting “HDAVI Control 2” or later. (> 47)

The following do not indicate a problem with this

unit:

≥Regular disc/video cassette rotating sounds.

≥Poor reception due to atmospheric conditions.

≥Image disturbance during search.

≥

Interruptions in reception due to periodic satellite broadcasting breaks.

≥Operations are slow to respond when “Power Save in Standby” is

activated.

≥Operations do not work due to a poor-quality disc. (Try again

using a Panasonic disc.)

≥The unit freezes due to one of its safety devices being activated.

(Press and hold [Í/I] on the main unit for 3 seconds.)

≥When the unit is turned on or off, there may be an unexpected

sound.

Power

Displays

TV screen and video

DMR-EX99VEG-VQT2J46_eng.book 88 ページ２０１０年１月１４日　木曜日　午前１０時３１分

1 2 ... 83 84 85 86 87 88 89 90 91 92 93 ... 99 100

Comments to this Manuals

No comments

Panasonic DMREX99V Operations Instructions Page 88

Comments to this Manuals

Related products and manuals for DVD players Panasonic DMREX99V