Panasonic TXP42G15B User Manual Page 83

  • Download
  • Add to my manuals
  • Print
  • Page
    / 88
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 82
On screen messages
Frequently Asked Questions
FAQs, etc.
83
Message Meaning / Action
All tuning data will be erased “Shipping Condition” will erase all tuning data (p. 47).
Are you sure ? Confirm correct operation.
Are you sure you want to delete this timer ?
Press OK to delete timer
Press RETURN to return
Confirm correct operation.
Bad signal
The signal is weak. Check the aerial is plugged in properly. It may
be necessary to have an aerial installer check the signal and aerial
alignment.
Reset channels. (p. 34 and p. 35)
Child Lock is active !
Press OK to enter PIN.
The selected channel is locked in Child Lock (p. 45). You must enter the
PIN number before the channel will be displayed.
Ethernet cable not connected
Check the connection of the LAN cable. If you use a hub, also check the
light on the hub is lit.
The LAN cable might be defective.
Faulty dish
The satellite cable might be short-circuited or there might be connection
problems of the cable. Check the cable and connection and then turn the
TV Off with the Mains power On / Off switch, and turn it On again.
If the message still persists, it may be necessary to have a dish installer
check the dish and cable.
Feature not available
It is not possible to record from COMPONENT, HDMI or PC. Connect the
recorder to the TV using a fully wired SCART cable for recording from the
TV tuner.
Confirm Q-Link or VIERA Link settings (p. 64 - 67).
Found new software version
∗∗∗
.
Press OK to start update
(may take 40 mins)
or Press EXIT to ignore
and you can update when TV is in standby.
There is a new software available.
Gateway does not answer.
Please confirm connection and setting of
router.
A connection failure has occurred and the gateway is not responding.
Check the settings and connections of the router.
Turn the TV and the router Off with the Mains power On / Off switch, and
turn them On again.
Invalid operation - Please check settings
and connections.
Check the Q-Link or VIERA Link connection and setting (p. 64 - 67).
Invalid system time. Please exit ! Cannot get the time information. Check the connection of the RF cable.
IP address conflict
Duplicate IP address has been detected. Check the IP address of other
equipment such as computers, routers and ensure that there are no
duplicate IP address.
IP address not set
An IP address is required to use interactive content through the internet.
Enter an IP address.
Manual IP setting not correct
The system is unable to set the IP address. Consult your Internet Service
Provider or telecommunications company.
Max. number of Timers already set ! The maximum number of timer programming events is 15.
New channels found!
Press OK to update channel list
Press EXIT to ignore.
There may be new channels available.
This message will appear each time a change is made by the
broadcasters. This message can be deactivated by setting “New Channel
Message” to Off in “DVB Tuning Menu”.
Selecting OK will perform “Update Channel List”.
No channel found.
Please check aerial or local signal
availability.
Press OK to start Auto Setup.
Please follow the message.
If it is still failed, consult your local Panasonic dealer.
No module inserted Check the CI module inserted completely (p. 49).
No recording - Check media The tape or disc may be “write protected”, missing or damaged.
No recording - Already recording
The equipment may already be recording.
No recording - Unknown reason
The recording may not be performed. Check the equipment.
Disc or tape may be full.
No service
The broadcaster has stopped the service. Check the channel in the TV
Guide. (p. 18 and p. 19)
No signal The TV cannot detect the signal. Check the connection of the RF cable.
On screen messages
Page view 82
1 2 ... 78 79 80 81 82 83 84 85 86 87 88

Comments to this Manuals

No comments