Panasonic WVCP650_SERIES Operations Instructions

Colour CCTV CamerasWV-CPR650/WV-CPR654(Lens : option)Before attempting to connect or operate this product,please read these instructions completely.FR

!3 Video Output Connector (VIDEO OUT)This connector is used to connect with the VIDEOIN connector of the monitor.!4 Power Cord SocketThis socket is us

Copper wire #24 #22 #20 #18size (AWG) (0.22mm2) (0.33mm2) (0.52mm2) (0.83mm2)Resistance 0.078 0.050 0.030 0.018Ω/mResistance 0.026 0.017 0.010 0.006Ω/

2. 24 V AC Power SupplyConnect the power cable to the AC/DC compatibleinput terminal on the rear panel of the camera.Copper wire #24 #22 #20 #18size (

-10-Type of RG-59/U RG-6/U RG-11/U RG-15/Ucoaxial cable (3C-2V) (5C-2V) (7C-2V) (10C-2V)Recommended (m) 250 500 600 800maximumcable length (ft) 825 1

-11-SYSTEM CONNECTIONa) Single Camera Connection (RS485 InterfaceModel/Half Duplex)SUPERDYNAMICSUPERDYNAMICSUPERDYNAMICSUPERDYNAMICSUPERDYNAMICb) Dais

-12-Installation of Auto Iris Lens ConnectorInstall the lens connector (YFE4191J100) when using avideo drive ALC lens.The installation should be made

Caution for Mounting the LensThe lens mount should be a C-mount or CS-mount (1”-32UN) and the lens weight should be less than 450g(0.99 lbs). If the l

The following adjustment should be made by qualifiedservice personnel or system installers.1. Loosen the screws on the back focal adjustingring.2. Tur

• Mounting from the bottomThis camera is designed to be mounted from thebottom, as shown below. The mounting hole is astandard photographic pan-head s

-16-1. CAMERA SETUP MENUCAM SET UP RS485UNITNUMBERSET UPCameraIDON/OFFCameraIDEditingSUPER-DONCamera IDDisplayPositionManualLevelSelectionSUPER-DOFFLi

CAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION: TO REDUCE THE RISK OF ELECTRICSHOCK, DO NOT REMOVE COVER (ORBACK), NO USER SERVICEABLE PARTSINSIDE.

-17-ManualLevelAdjustmentMotionDetectorOFF/ONLens DriveSignalSelectionDC VideoSpecialmenuDetectionLevelAdjustmentDetectionMasking AreaSelectio

-18-Left ButtonSet SwitchRight ButtonDown ButtonUp ButtonUp Button (): This button is used to move thecursor upwards. Use this button toselect an item

-19-• Opening the Setup MenuPress and hold down for a second or longer. ** SET UP **CAMERA RS485 END SET UP DISABLE↵↵The SET UP menu appear

-20-• Editing the SPECIAL menuTo edit the SPECIAL menu (change settings), proceedas for editing the CAM SET UP menu above.Move the cursor to RET, then

-21-SETTING PROCEDURESUNIT NUMBERThis item is used to select the camera number that isused with RS485 communication.1. Move the cursor to the paramete

-22-X ON/X OFFThis item is used to select applying the flow control ornot.1. Move the cursor to the X ON/X OFF parameter.2. Select NOT USE (not apply

-23-3. Move the cursor to the character you want tochange by pressing / / / .4. After selecting the character, press . Theselected character appears

-24-2. Move the pointer to the character to be edited bypressing or . Then move the cursor to thecharacter area and select a new character.3. Press

-25-2-1. ALC Mode with SUPER-D ONSuper Dynamic Function (SUPER-D)The important object in a scene is usually placed in thecentre of the monitor’s scree

-26-2. Move the cursor to MASK SET and press . The48 mask areas appear on the monitor screen. Thecursor is blinking in the top left corner of thescre

-27-4. Repeat step 1 to 3 to mask the desired area. Tocancel masking, move the cursor to that area andpress .5. After masking is completed, press for

-28-4. Gain Control Setting (AGC ON/OFF)You can set the gain (brightness level portion of animage) to automatic level adjustment (ON) or fixedlevel (O

-29-6. Synchronization Setting (SYNC)You can select internal sync mode (INT) or line-lockmode (LL). Additionally, this model accepts the VBSsignal (co

-30-6. The VS gen-lock mode has its own menu for hori-zontal phase adjustments. When the cable lengthof the video output or the gen-lock input ischang

-31-8. Adjust the horizontal phase by pressing or. The adjustable range is 0 - 2.0µs.9. Move the cursor to SC COARSE. The cursor startsblinking.10. P

-32-4. After confirming the cursor is on EXT (VS), press. The phase adjustment menu appears on themonitor.6-2. VS Gen-lock Mode (EXT(VS))1. Move the c

-33-2. After confirming the cursor is on LL, press .The vertical phase adjustment menu appears onthe monitor.3. Move the cursor to COARSE. The cursor

-34-• To reset COARSE and FINE to the values pre-set at the factory, press or simultane-ously. COARSE and FINE adjustments arepreset at the factory

-35-2. Press to start the white balance setup. Thewords PUSH SW start blinking to indicate that thewhite balance is being set.Blinking ** CAM SET U

-36-8. Motion Detector Setting (MOTION DET)The motion detector detects the moving objects in thescene by monitoring the brightness level changes. Youc

-1-THIS APPARATUS MUST BE EARTHED.To ensure safe operation the three-pin plug supplied must be insertedonly into a standard three-pin power point whic

-37-Note:Masking or adjusting the detection level is neededto prevent malfunction under the following condi-tions:• When shooting an object under flic

-38-10. Special Menu (SPECIAL)This menu lets you adjust and set up the video signalof the camera to meet your requirements.Move the cursor to RET on t

-39-To reset to the factory settings1. Move the cursor to the CAMERA RESET parame-ter. The words PUSH SW start blinking.2. While holding down and ,

-40-When the camera is aimed at a bright light, such as aspotlight, or a surface that reflects bright light, smearor blooming may appear. Therefore,

Pick-up Device: 753 (H) x 582 (V) pixels, Interline Transfer CCDScanning Area: 4.8 (H) x 3.6 (V) mm (Equivalent to scanning area of 1/3” pick-up tube)

-42-Power Source and WV-CPR650: 220 - 240V AC 50 Hz, 6.3WPower Consumption: WV-CPR654: 24V AC 50 Hz, 6.3W12V DC, 690 mADimensions (without lens): 67 (

Matsushita Electric Industrial Co., Ltd.Central P.O. Box 288, Osaka 530-91, JapanN1097-1117 YWV8QA4721BN Printed in JapanImprimé au JaponN 30

CONTENTSPREFACE ...

1. The following functions are built in.(1) Auto Light Control (ALC)/Electronic LightControl (ELC)(2) The SUPER-D function eliminates interferenceby s

1. Do not attempt to disassemble the camera.To prevent electric shock, do not remove screwsor covers.There are no user serviceable parts inside. Ask a

SUPERDYNAMICWV-CPR650SUPERDYNAMICWV-CPR650Hi-Z G/L 75ΩVIDEO OUTPOWER220-240V-50HzGEN-LOCKRS485(A)(B)GNDVIDEO OUTPOWERGEN-LOCKRS485(A)(B)GNDAC 24VIN

q Auto Iris Lens ConnectorThis connector is used to connect with the auto irislens by a 4-pin male connector that is supplied asa standard accessory (