Panasonic SCHTB18EB Operations Instructions download pdf (Page 20)

VQT5J46

Reference

Troubleshooting

Before requesting service, make the following checks. If

you are in doubt about some of the check points, or if the

solutions indicated in the following guide do not solve the

problem, consult your dealer for instructions.

No power.

≥ Insert the AC mains lead securely. (> 10)

≥ If the indicators blink and the main unit turns off

immediately after you have turned it on, unplug the AC

mains lead and consult your dealer.

The remote control does not work properly.

≥ The battery is depleted. Replace it with a new one.

(> 8)

≥ It is possible that the insulation sheet has not been

removed. Remove the insulation sheet. (> 8)

≥ It may be necessary to set the code of the remote

control again after changing the battery of the remote

control. (> 19)

≥ Use the remote control within the correct operation

range. (> 8)

The “TV” indicator blinks.

Unplug the AC mains lead and consult your dealer. If

other indicators are also blinking, be sure to inform your

dealer of these indicators.

The main unit is automatically switched to

standby mode.

“Auto Power Down” function is on.

The main unit will automatically switch to standby mode

when no signal is input and no operation is performed for

approx. 2 hours. Refer to page 18 to turn this function off.

Pairing cannot be done.

Check the Bluetooth

device condition.

The device cannot be connected.

≥ The pairing of the device was unsuccessful or the

registration has been replaced. Try pairing the device

again. (> 11)

≥ This system might be connected to a different device.

Disconnect the other device and try pairing the device

again.

The device is connected but audio cannot be

heard through this system.

For some built-in Bluetooth

devices, you have to set the

audio output to “SC-HTB18” manually. Read the operating

instructions for the device for details.

The sound is interrupted.

≥ The device is out of the 10 m communication range.

Bring the Bluetooth

device closer to the main unit.

≥ Remove any obstacle between the main unit and the

device.

≥ Other devices that use the 2.4 GHz frequency band

(wireless router, microwaves, cordless phones, etc.) are

interfering. Bring the Bluetooth

device closer to the

main unit and distance it from the other devices.

No sound.

≥ Turn muting off. (> 17)

≥ Check the connections to the other device. (> 9)

≥ Make sure that the received audio signal is compatible

with this system. (> 23)

≥ Turn this system off and then on again.

≥ If the connections are correct, there might be a problem

with the cables. Redo the connections with different

cables.

≥

Check the audio output settings on the connected device.

The volume is lowered when the main unit is

turned on.

If the main unit is turned off with the volume setting in the

greater half (above 50), the main unit will automatically

lower the volume to the middle (50) when the main unit is

turned on. (> 19)

The dialog is too persistent or the dialog does

not sound natural.

This system has a function to make the dialog stand out

when the volume is low. (> 17)

To return to the factory defaults.

While the main unit is on, press and hold [Í/I] on

the main unit for more than 4 sec.

(All the indicators will blink twice when this

system is reset.)

If this system does not operate as expected,

returning the settings to the factory defaults

may solve the problem.

≥

The remote control code will return to “1” when

this system is returned to the factory preset. To

change the remote control code, refer to page 19.

General operation

Bluetooth

Sound

SC-HTB18EGEB_VQT5J46-1.book 20 ページ２０１５年２月４日　水曜日　午後３時１８分

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 26 27 28

Comments to this Manuals

No comments

Panasonic SCHTB18EB Operations Instructions Page 20

Comments to this Manuals

Related products and manuals for Speaker sets Panasonic SCHTB18EB