Panasonic BMED500 Operations Instructions download pdf (Page 16)

Description and settingOperation mode

Set to this mode when you make iris

cameras enroll people.

Set to this mode when you configure

the control unit's operations via the

administration PC. (Refer to the

administrator’s guide supplied with

the administration software

SETTINGS

■ Description

To use the control unit, the following settings are necessary

with the setting switches or numeric buttons on the setting

board.

• Setting/confirmation of the operation mode/IP address

(Operation mode switches)

• Electric lock setting (DSW 2)

You will set the existence, type, polarity and unlocking

timer of electric locks.

• IP address

You will set if you connect the control unit to the PC via

LAN and control this unit from the PC.

In addition to these settings, you need the configuration

through the administration PC. (Refer to the administrator’s

guide of the administration software.)

Note: When you set the control unit's operations through

the administration PC, you need to change the opera-

tion mode to the SETUP mode.

■ To Do Setting without the

Buzzer Sound

When you open the door, the buzzer will beep to notify you

that the door is open. Then, the recognition procedures with

iris cameras will be unavailable. If you open the door for

maintenance, etc., do the following procedure.

1. Open the door with the supplied key.

The buzzer will beep and recognition is stopped.

2. Pull the door sensor.

3. Restart the recognition from the administration PC.

You can do setting without the buzzer sound and you

can continue the recognition with iris camera during the

setting. (Setting changes will not be reflected until turn-

ing on the power again.)

4. After the setting, close the door.

The buzzer will beep again.

5. Restart the recognition from the administration PC.

When you open the door again for setting, do steps 1 to

3 again.

■ Operation Mode Setting

The control unit has four operation modes. They are config-

urable with 1 to 3 of the operation mode switches. (The fac-

tory default setting is shown in the figure.)

Notes:

• Change the operation mode after turning off the power

of the control unit. When you change the mode while

power is on, the setting will not be reflected to the con-

trol unit until turning on the power again.

• To turn the power off, refer to p.19.

POWER ALARM S3 S2 S1

CN1

1 2 3 4 5

6 7 8 9

RESET

MIN

+–

BZ1

VR1

MAX

OFF FSK

2 3 4 5 6 7 8

Door sensor

Pull this immediately after

opening the door.

Operation mode switches

(DSW3)

POWER ALARM S3 S2 S1

CN1

IC102

E102E101CN504CN503

CN101

1 2 3 4 5

6 7 8 9

RESET

MIN

DSW1

DSW2

+—

BZ1

VR1

MAX

OFF FSK

2 3 4 5 6 7 8

OFF FSK

2 3 4 5 6 7 8

OFF FSK

2 3 4 5 6 7 8

OFF

2 3 4 5 6 7 8

Unsettable

(Do not change these positions. Error may occur.)

Operation mode

setting

IP setting mode This is the mode to set/confirm the IP

address/gateway address of the

control unit.

OFF FSK

2 3 4 5 6 7 8

OFF FSK

2 3 4 5 6 7 8

OFF FSK

2 3 4 5 6 7 8

SETUP mode

Recognition

mode

Set to this mode when you make iris

cameras recognize people.

OFF FSK

2 3 4 5 6 7 8

Enrollment mode

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 25 26

Comments to this Manuals

No comments

Panasonic BMED500 Operations Instructions Page 16

Comments to this Manuals

Related products and manuals for Supplementary music equipment Panasonic BMED500