Panasonic AK-MSU930P User Manual download pdf (Page 7)

BRIGHT: Dot matrix display brightness setting

This is used to set the brightness of the

dot matrix display.

BUZZ: Buzzer setting

This is used to set the buzzer to ON or

OFF.

<CARD>: SD card read/write setting

This is used to write the camera’s data

on the SD card or read it from the card.

System switches [SYSTEM]

These are the system setting switches used to set the

down-converter mode, select the down-converter filter,

select GBR or YPbPr for the HDTV video output, select

GBR or YPbPr for the SDTV video output, select the up-

converter mode, select whether the CCU waveform

monitor control connector is to be used for SDTV or

HDTV applications, and so on.

HEAD, CCU RCV LEVEL:

Camera head, CCU unit light reception

strength level displays

These indicate the light reception

strength margins of the camera head and

CCU.

RET1, RET2, RET3, RET4: Return video settings

These are used to set the input

allocations of the return signals.

D/C MODE: Down-conversion system selection

This is used to select the down-

conversion system.

U/C MODE: Up-conversion system selection

This is used to select the up-conversion

system.

D/C LINK: Down-conversion link

This is used to decide whether to go with

the down-conversion system control

based on the AUX external input or set

the down-conversion independently.

U/C LINK: Up-conversion link

This is used to decide whether to go with

the up-conversion system control that is

linked to the down-conversion system or

set the up-conversion independently.

HD BAR: HD color bar made setting

This is used to select the HD color bar

mode.

SD BAR: SD color bar mode setting

This is used to select the SD color bar

mode.

PATHO: Pathological pattern output

This is used to forcibly output the

pathological pattern.

SET UP: Color bar setup setting

This is used to set the color bar setup.

OUTPUT SEL: Output selection

This is used to set the analog output of

the CCU to RGB or YPbPr.

MONI SEL: Monitor switch selection setting

This is used to set the monitor switch

selection to PM, WFM or the PM-WFM

link mode.

Parts and their functions

Black gamma control switch [BLK GAMMA CONTROL]

This is operable when the lamp of the BLK GAMMA ON

switch among the MODE ON/OFF switches is lighted. It

is selected to adjust the black gamma curve.

When the switch is selected, its lamp lights.

BLKR, BLKM, BLKB GAM:

Black gamma curve (R, MASTER or B)

Adjustment range: –32 (black compression) to

+31 (black expansion)

LEVEL: Black gamma level

Setting: LOW (brightness level: approx. 20%),

HI (brightness level: approx. 30%)

Matrix control switch [MATRIX CONTROL]

This is pressed to change the correction amounts for the

R-G, R-B, G-R, G-B, B-R and B-G chroma saturation.

MTX 12, SATU, PHASE

These are used to select the following 12-axis matrix

adjustment items: G, G_Cy, Cy, Cy_B, B, B_Mg, Mg,

Mg_R, R, R_Ye, Ye and Ye_G.

FUNC switches [FUNC]

ALC LEVEL: Auto iris level

This is used to adjust the auto iris level of

the lens iris.

SPEED: Auto iris speed

This is used to set the feedback speed of

the auto iris.

WINDOW: Auto iris window

This is used to set the image detection

area window of the auto iris.

PEAK: Peak/average setting

This is used to set the ratio between the

average and peak values of the auto iris

image detection.

FAN POWER: Fan power switch

This is used to set the power of the

camera head’s fan to ON or OFF.

FAN SPEED: Fan speed

This is used to set the speed of the

camera head’s fan.

2D-M: Component 2-dimensional low-pass filter

This is used to set whether to apply the

2-dimensional low-pass filter to the

SDTV component output.

2D-E: Composite 2-dimensional low-pass filter

This is used to set whether to apply the

2-dimensional low-pass filter to the

SDTV composite output.

COMB: Comb filter mode

This is used to set the comb filter mode.

SETUP MODE: Auto setup mode setting

This is used to select the auto setup

mode setting.

REF FILE: File select

This is used to select the file attribute to

be referenced when auto setup has been

started.

MPED SET: Auto setup MPED convergence value

This is used to set the position where the

master pedestal is to be converged when

auto setup has been started.

1 2 3 4 5 6 7 8 9 10 11 12 ... 15 16

Comments to this Manuals

No comments

Panasonic AK-MSU930P User Manual Page 7

Comments to this Manuals

Related products and manuals for Tools Panasonic AK-MSU930P