Panasonic DMRES35V User Manual download pdf (Page 67)

RQTV0136

Operation Page

Picture Page

Cannot operate the TV. ≥Change manufacturer code. Some TVs cannot be operated even if you change the code. 15

Cannot operate the DVD. ≥Press [DRIVE SELECT] to select the DVD. 10

Cannot operate the VHS. ≥Press [DRIVE SELECT] to select the VHS. 10

The remote control does not work. ≥The remote control and main unit are using different codes. Change the code on the remote

control.

≥Press and hold [ENTER] and the indicated number button at the same time for more than

2 seconds.

≥The batteries are depleted. Replace them with new ones.

It may be necessary to reset the code on the remote control again after changing the batteries.

≥Point the remote control at the remote control sensor on the main unit.

≥Remove obstacles between the remote control and main unit.

≥Coloured glass may obstruct the signal reception/transmission.

≥Do not place the signal sensor in direct sunlight or in areas that may be subject to sunlight

exposure.

≥The child lock function is activated.

The unit is on but cannot be

operated.

≥Some operations are prohibited by the disc.

≥The unit is warm (“U59” appears on the unit’s display). Wait until “U59” disappears.

≥One of the unit’s safety devices may have been activated.

Reset the unit as follows:

(1) Press [Í/I] on the main unit to switch to standby.

If the unit does not switch to standby, press and hold [Í/I] on the main unit for about

10 seconds. The unit is forcibly switched to standby.

Alternatively, disconnect the AC mains lead, wait for about 1 minute, then reconnect it.

(2) Press [Í/I] on the main unit to turn the unit on.

≥The child lock function is activated.

–

Cannot eject a disc. ≥The unit is recording.

≥The unit may have a problem. While the unit is off, hold down [∫] and [CH, W] on the main unit

simultaneously for about 5 seconds. Remove the disc and consult the dealer.

≥The child lock function is activated.

–

Cannot tune channels. ≥Check the connections. 12

Startup is slow. ≥Make sure that “Quick Start” is set to “On”.

Even if “Quick Start” is set to “On”, startup is slow if the clock is not set, there was a power failure

or the AC plug has just been connected.

≥A few dozen seconds after turning on the unit, you can play a disc or start recording to discs other

than DVD-RAM.

≥Startup takes time for a few minutes after 5:15 a.m. due to system maintenance of this unit.

–

Takes time to read DVD-RAM. ≥It may take time to read a disc if it is being used for the first time in this unit or it has not been used

for a long time.

–

TV reception worsens after

connecting the unit.

≥This can occur because the signals are being divided between the unit and other equipment. It can

be solved by using a signal booster, available from audio-visual suppliers.

–

The images from the unit do not

appear on the TV.

Picture is distorted.

≥Make sure that the TV is connected to the VIDEO OUT terminal, S VIDEO OUT terminal or

COMPONENT VIDEO OUT terminals on the unit.

≥Make sure that the TV’s input setting (e.g., AV 1) is correct.

≥The TV is not compatible with progressive signals. Press and hold [∫] and [“ DVD, COPYING] on

the main unit at the same time for about 5 seconds. The setting will change to interlace.

12, 13

–

The TV screen is distorted when

switching the DVD/VHS.

≥The colour of the screen may turn to monochrome or the screen may be distorted depending on

the TV used when you switch the DVD/VHS. However, this is not a malfunction.

–

On-screen messages do not

appear.

≥Select “Automatic” in “On-Screen Messages” in the Setup menu. 58

The grey background does not

appear.

≥Select “On” in “Grey Background” in the Setup menu. 58

The 4:3 aspect ratio picture

expands left and right.

Screen size is wrong.

≥Use the TV to change the aspect. If your TV does not have that function, set “Progressive” in the

Picture menu to “Off”.

≥Check the settings for “TV Aspect” in the Setup menu.

There is a lot of after-image when

playing video.

≥Set “Copy NR” in the Picture menu to “Off”. 35

When playing DVD-Video using

progressive output, one part of the

picture momentarily appears to be

doubled up.

≥Set “Progressive” in the Picture menu to “Off”. This problem is caused by the editing method or

material used on DVD-Video, but should be corrected if you use interlace output.

There is no apparent change in

picture quality when adjusted with

the Picture menu in the on-screen

menus.

≥The effect cannot be seen with certain types of video. –

Troubleshooting guide

RQTV0136.book 67 ページ２００６年４月１９日　水曜日　午後１時２８分

1 2 ... 62 63 64 65 66 67 68 69 70 71 72 ... 75 76

Comments to this Manuals

No comments

Panasonic DMRES35V User Manual Page 67

Comments to this Manuals

Related products and manuals for DVD players Panasonic DMRES35V