Panasonic SCHT1000 Operations Instructions download pdf (Page 34)

RQT7061

RADIO &

SOUND

The radio

Preparation

≥Switch [HOME THEATER, TV] to “HOME THEATER”.

≥Press [FM/AM] to select “FM” or “AM” as the source.

1 Press [X TUNING] or [TUNING W] to

select the frequency of the required

station.

Remote control: Press [6] or [5].

TUNED: Displayed when a radio station is

tuned.

ST: Displayed when a stereo FM

broadcast is being received.

Press and hold [X TUNING] or [TUNING W] ([6] or [5]

on the remote control) until the frequency starts scrolling to

start automatic tuning. Tuning stops when a station is found.

2 Adjust the volume.

[Main\unit\only]

∫ If noise is excessive

Press [FM MODE].

Each time you press the button:

FM: Changes between stereo and forced monaural.

AM: BP1()BP2 (BPlBeat Proof)

Select either BP1 or BP2, whichever receives better reception.

The FM mode is canceled when you change the frequency.

∫ FM frequency step

The step is factory-set to 0.2 MHz, but you can change it to receive

broadcasts allocated 0.1-MHz steps.

1 Press [FM/AM] to select “FM”.

2 Press and hold [FM/AM].

After a few seconds the display changes to show the current

minimum frequency. Continue to hold the button down. The

minimum frequency changes and the step is changed.

To return to the original step, repeat the above steps.

[Note]

Any FM and AM frequencies preset in channels will be initialized by

this procedure. Preset them again.

Preset channels to make selection simple.

Up to 12 stations can each be set in the FM and AM bands.

[Main\unit\only]

1 Tune to “FM 87.9” MHz or “FM

87.5” MHz (➡ left).

2 Press and hold [MEMORY].

Release the button when “AUTO” is displayed.

The tuner presets all the stations it can receive into the

channels in ascending order.

“SET OK” is displayed when the stations are set. The last

station to be set is then played.

3 Tune to “AM 520” kHz.

Repeat step 2 for AM automatic presetting.

“ERROR” is displayed

Presetting was unsuccessful. Preset manually.

[Main\unit\only]

1 Tune to the station (➡ left).

2 Press [MEMORY].

3 While “MEMO” is flashing

Press [X, W CHANNEL] to select a

channel and press [MEMORY].

The station occupying a channel is erased if another station is preset

in that channel.

1 Press [FM/AM] to select “FM” or

“AM”.

2 Press the numbered buttons or

[W X CH] to select the channel.

e.g., “2”: [0] ➡ [2]

“12”: [1] ➡ [2]

[Note]

If there is nearby electrical interference during auto tuning the

frequency may come to a halt without locating a channel. Turn off the

power of the nearby electrical equipment.

Manual tuning

VOLUME

SKIP

STOP PAUSE PLAY/x1.3

SLOW/SEARCH

CANCEL

123

789

100

HOME THEATER TV

CH SELECT

RETURN

L1/OPT

FUNCTIONS

TOP MENU

ENTER

DIRECT NAVIGATOR

PLAY LIST

MIX

2CH

TEST

FM/AM

TV/VIDEO

INPUT SELECTOPEN/CLOSE

DISPLAY

DVD

VCR Plus+

POWERPOWER

PRO LOGIC

6, 5

HOME

THEATER,TV

W X CH

r s VOLUME

FM/AM

DOWN

TIME SLIP

REC

ERASE

MEMORY

FM/AM

DVD

REC MODE

FM MODE

VOLUME

OPEN/CLOSE

TUNING

TIME SLIP

CHANNEL

PHONES

X, W CHANNEL

FM/AM

MEMORY

FM MODE

VOLUME DOWN, UP

X TUNING W

Numbered

buttons

TUNED

Preset tuning

Automatic presetting

Manual presetting

Selecting channels

MEMO

TUNED

7061en.book 34 ページ２００３年７月１日　火曜日　午前１１時４４分

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 55 56

Comments to this Manuals

No comments

Panasonic SCHT1000 Operations Instructions Page 34

Comments to this Manuals