Panasonic CS-A9CKPG User Manual Page 37

  • Download
  • Add to my manuals
  • Print
  • Page
    / 82
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 36
Operation Details
COOL – Cooling Operation
To set the room temperature at your preference
cooling comfort.
AUTO – Automatic Operation
Sense indoor temperature to select the optimum
mode.
Temperature is not displayed on the remote control
during AUTO operation.
DRY – Soft Dry Operation
A very gentle Cooling Operation, prior to
dehumidification. It does not lower the room
temperature.
During Soft Dry operation, the indoor fan operates at
Low fan speed.
HEAT – Heating Operation
(for Heat Pump Model only)
Heat is obtained from outdoor air to warm up the
room. When the outdoor ambient air temperature
falls, the heating capacity of the unit might be
reduced.
Defrosting Operation
Depending on the outdoor temperature, the operation
occasionally stops to melt the frost on the outdoor
unit.
FAN – Air Circulation Operation
(for Cooling Model only)
When the room temperature reaches the set
temperature, operation commences at Low airflow
volume. It stops when the room temperature drops to
4°F below the set temperature.
(It is useful when using a heater).
Hi fan speed will not operate when using the air
circulation Fan mode.
Setting the Horizontal Airflow Direction
• Adjust it manually
Notes
If the unit is not going to be used for an extended
period of time, turn off the main power supply. If it is
left at the ON position, approximately 2.5 W of
electricity will be used even if the indoor unit has been
turned off with the remote control.
If operation is stopped, then restart immediately, the
unit will resume operation only after 3 minutes.
P
O
W
E
R
P
O
W
E
R
T
I
M
E
R
T
I
M
E
R
Q
U
I
E
T
Q
U
I
E
T
P
O
W
E
R
F
U
L
P
O
W
E
R
F
U
L
P
O
W
E
R
F
U
L
P
O
W
E
R
F
U
L
E
C
O
N
O
M
Y
E
C
O
N
O
M
Y
E
C
O
N
O
M
Y
E
C
O
N
O
M
Y
P
O
W
E
R
P
O
W
E
R
T
I
M
E
R
T
I
M
E
R
Q
U
I
E
T
Q
U
I
E
T
MANUAL
Five stages of adjustment
can be made between
14 ~ 36 angle.
MANUAL
Five stages of adjustment
can be made between
0 ~ 61 angle.
Heat Pump Model
MANUAL
Five stages of adjustment
can be made between
14 ~ 36 angle.
MANUAL
Five stages of adjustment
can be made between
0 ~ 61 angle.
– When the discharge air
temperature is low such
as at the start of heating
operation, the air blows
in a horizontal direction.
As the temperature
rises, the hot air blows
in a downward direction.
– To stop this operation,
press MANUAL.
HEAT Operation
AUTO
COOL / DRY Operation
AUTO
Swing up/down
Automatically
36°
Swing up/down
Automatically
Move up/down
Automatically
36° 61°
COOL / DRY Operation
AUTO
FAN Operation
AUTO
Setting the Fan Speed
Press 4 to select:-
FAN Low Fan Speed
FAN Medium Fan Speed
FAN High Fan Speed
AUTO
FAN Automatic Fan Speed
The speed of the indoor fan is adjusted
automatically according to the operation.
The indoor fan stops occasionally during
cooling operation.
Setting the Vertical Airflow Direction
Press 5 or 6 to select:-
Cooling Model
Use this air conditioner under the following
conditions:
Heat Pump Model
DBT: Dry Bulb Temp
WBT: Wet Bulb Temp
Maximum Temperature
Minimum Temperature
WBT
73.4
51.8
DBT
109.4
60.8
WBT
78.8
51.8
Indoor Outdoor
(Unit in °F)
DBT
89.6
60.8
DBT: Dry Bulb Temp
WBT: Wet Bulb Temp
Maximum Temperature-Cooling
(Maximum Temperature-Heating)
Minimum Temperature-Cooling
(Minimum Temperature-Heating)
DBT
89.6
(86)
60.8
(60.8)
WBT
73.4
(–)
51.8
(–)
DBT
109.4
(75.2)
60.8
(23)
WBT
78.8
(64.4)
51.8
(21.2)
Indoor Outdoor
(Unit in °F)
Cooling Model
SETTING THE TIMER
Ensure that the current time is correct before setting
the timer. The timer cannot be set if the time display
is flashing.
ON-TIMER Operation
To start the air conditioner operation automatically.
Press 1 to set the operation.
Press 2 to increase or decrease the time.
Then press 3.
To cancel this operation, press 4.
OFF-TIMER Operation
To stop the air conditioner operation automatically.
Press 5 to set the operation.
Press 2 to increase or decrease the time.
Then press 3.
To cancel this operation, press 4.
Timer Mode Operation Details
When the ON-Timer is set, operation will start
before the actual set time. This is to enable the
room temperature reaches the set temperature at
the set time.
Once the ON/OFF Timer is set, operation will
start/stop at the set time everyday.
The current time is not displayed when the timers
are set.
When both timers are used together, the TIMER
mode indicator on the indoor unit remains lit even
when the operation is stopped by the OFF-TIMER.
CHECK
AUTO
AUTOHEAT DRYFANCOOL
FAN
AUTO
RESET CLOCK
MODE
POWERFUL
ECONOMY
FAN SPEED
AIR SWING
OFF
CANCEL
ON
SET
1
2
3
TIMER
OFF/ON
QUIET
AUTO
MANUAL
3
6
4
1
7
5
2
8
Heat Pump Model
COOL,DRY, –>15 minutes
in advance
HEAT, AUTO–>30 minutes
in advance
Cooling Model
COOL,DRY, –>15 minutes
AUTO in advance
CONVENIENCE OPERATION
Powerful Mode Operation
To obtain the set temperature quickly.
Press 6.
* Powerful mode indicator (orange) on the indoor
unit will light up.
* Powerful mode will operate for 15 minutes only.
To cancel this operation, press once more.
Economy Mode Operation
To save electrical power consumption.
Please use this mode when the room has reached
your desired temperature.
Press 7.
* Economy mode indicator (green) on the indoor unit
will light up.
Press once more to cancel this operation.
Economy/Powerful Mode Operation Details
Economy and Powerful operation cannot be
selected simultaneously.
The changes of the temperature and airflow volume
are automatic.
The remote control display remains unchanged.
If operation mode button is pressed, economy or
powerful operation will be cancelled.
During FAN – Air circulation operation, the powerful
and economy operation are not available.
(for Cooling Model only)
Quiet Mode Operation
To provide quiet operation.
Press 8.
*
Quiet mode indicator on the indoor unit will light up.
To cancel this operation, press once more.
Operation Details
Air flow sound will reduce during operation.
Airflow
volume
Super Low
Automatic
Economy Mode
Operation
COOL / DRY
HEAT
(for Heat Pump
model only)
Temperature
1°F higher
than set temp.
1°F lower
than set temp.
Airflow
volume
Super High
Automatic
Powerful Mode
Operation
COOL / DRY
HEAT
(for Heat Pump
model only)
Temperature
5°F lower
than set temp.
5°F higher
than set temp.
37
CS-A9CKPG CU-A9CKP6G / CS-A12CKPG CU-A12CKP6G
Page view 36
1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 81 82

Comments to this Manuals

No comments