Panasonic DMREH55 Operations Instructions download pdf (Page 68)

RQT8365

Messages

On the television (Continued)

Page

On the unit’s display

The following messages or service numbers appear on the unit’s display when something unusual is detected during startup and use.

The messages are alternately displayed.

This is a non-recordable disc. ≥The unit cannot record on the disc you inserted. Insert a DVD-RAM, +RW or unfinalized

DVD-R, DVD-RW (DVD-Video format) or +R.

≥You cannot directly record to DVD-R DL, and +R DL discs with this unit. You must first

record to the HDD, and then copy from the HDD to disc.

≥You inserted an unformatted DVD-RAM, DVD-RW, +R, +R DL or +RW.

4–6

—

This disc is not formatted

properly.

Insufficient Hard Drive space.

Four hours (SP) of free hard

drive space is needed in order

to start copying to DVD-R/+R

DL (D.Layer) disc.

Too many titles on the Hard

Drive. To allow titles to be

copied to a DVD-R/+R DL

(D.Layer) disc, please delete

unnecessary titles.

≥

[-R]DL]

[+R]DL] It is not possible to copy when there is not enough free space on the HDD or

when the total number of the recorded titles on the HDD and the titles to be copied are

greater than 500.

Delete unwanted titles from the HDD.

Rental Expired. ≥The DivX VOD content has zero remaining plays. You cannot play it. (DivX) —

≥The operation is prohibited by the unit or disc. —

HARD ERR

≥If there is no change after turning the unit on and off, consult the dealer where the unit was

purchased.

—

No AUDIO

≥

When connecting to CPPM incompatible equipment with an HDMI cable, CPPM copy proctected

DVD-Audio cannot output audio through the HDMI AV OUT terminal. Connect the audio cable of

the Audio/Video cable (Red, White) or optical digital cable to the corresponding terminals.

14–16

No READ

≥The disc is dirty or badly scratched. The unit cannot record, play, or edit.

≥You have used a DVD lens cleaner and it has finished. Press [< OPEN/CLOSE] on the

main unit to eject the disc.

PLEASE WAIT

≥Displayed when the unit is started. This is not a malfunction.

≥The unit is carrying out its recovery process. You cannot operate the unit while “PLEASE

WAIT” is displayed.

—

SET 

(“∑” stands for a number.)

≥The remote control and main unit are using different codes. Change the code on the

remote control.

Press and hold [ENTER] and the indicated number button at the

same time for more than 2 seconds.

SLEEP ≥In order to extend HDD life, the HDD is in SLEEP mode. 9

SP 35:50

LP 151h

“SP”, “LP” and the numbers are

examples.

≥Available space on the HDD or disc.

The example “SP 35:50” is displayed when less than 100 hours are available and the

example “LP 151h” is displayed when over 100 hours are available.

“SP” and “LP” are recording modes, “35:50” means “35 hours 50 minutes” and “151h”

means “151 hours”.

UNFORMAT

≥You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or DVD-

RW (DVD-Video format) that has been recorded on other equipment.

Format the disc to use it. However all the recorded contents on a disc are deleted.

—

UNSUPPORT

≥You have inserted a disc the unit cannot play or record on. 4–6

F74 ≥The HDMI connection could not be authenticated due to a transfer malfunction.

Consult your local dealer for more information.

—

F75 ≥The HDMI connection could not be authenticated due to an internal data malfunction.

Consult your local dealer for more information.

—

U59 ≥The unit is hot.

The unit switches to standby for safety reasons. Wait for about 30 minutes until the

message disappears.

Select a position with good ventilation when installing the unit. Do not block the cooling fan

on the rear of the unit.

—

U61 ≥(When a disc is not inserted) Displays when a malfunction has occurred during recording,

playback or copy. This is displayed when the unit is in the recovery process to return to

normal operation; it is not broken. Once the display clears you can use the unit again.

—

U71 ≥The connected equipment is not HDMI compatible. —

U72

U73

≥The HDMI connection acts unusually.

–The connected equipment is not HDMI compatible.

–Please use HDMI cables that have the HDMI logo (as shown on the cover).

–The HDMI cable is damaged.

—

U88

≥

(When a disc is inserted) Displays when there was something unusual detected with the disc

while playback or copy. This is displayed when the unit is in the recovery process to return to

normal operation; it is not broken. Once the display clears you can use the unit again.

U99 ≥The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch the unit to

standby. Now press [POWER Í/I] on the main unit again to turn the unit on.

—

H or F ≥There is something unusual. (The service number displayed after H and F depends on the

unit’s condition.)

≥Check the unit using the troubleshooting guide. If the service number does not disappear,

do the following.

1. Disconnect the plug from the AC outlet, wait a few seconds, then reconnect it.

2. Press [POWER Í/I] to turn the power on. (The unit may be fixed.)

If the service number does not disappear despite doing the above, request service from

the dealer. Inform the dealer of the service number when requesting service.

—

69–74

EH55English.book Page 68 Thursday, April 6, 2006 9:28 PM

1 2 ... 63 64 65 66 67 68 69 70 71 72 73 ... 83 84

Comments to this Manuals

No comments

Panasonic DMREH55 Operations Instructions Page 68

Comments to this Manuals

Related products and manuals for DVD players Panasonic DMREH55