Panasonic TH85PF12E User Manual download pdf (Page 10)

SERIAL

6 7 8 9

1 3 4 5 2

SERIAL Terminals connection

Notes:

• Use the RS-232C straight cable to connect the computer to the Plasma Display.

• The computer shown is for example purposes only.

• Additional equipment and cables shown are not supplied with this set.

The SERIAL terminal conforms to the RS-232C interface

speciﬁ cation, so that the Plasma Display can be controlled

by a computer which is connected to this terminal.

The computer will require software which allows the

sending and receiving of control data which satisfies

the conditions given below. Use a computer application

such as programming language software. Refer to the

documentation for the computer application for details.

The SERIAL terminal is used when the Plasma Display is controlled by a computer.

Pin layout for SERIAL Terminal

Basic format for control data

The transmission of control data from the computer

starts with a STX signal, followed by the command, the

parameters, and lastly an ETX signal in that order. If there

are no parameters, then the parameter signal does not

need to be sent.

STX C1 C2 C3 P1 P2 P3 P4: P5 ETX

Start

(02h)

3-character

command (3 bytes)

Colon Parameter(s)

(1 - 5 bytes)

End

(03h)

Notes:

• If multiple commands are transmitted, be sure to wait for

the response for the ﬁ rst command to come from this unit

before sending the next command.

• If an incorrect command is sent by mistake, this unit will

send an “ER401” command back to the computer.

• SL1A, SL1B, SL2A and SL2B of Command IMS are

available only when a dual input terminal board is

attached.

COMPUTER

RS-232C Straight cable

D-sub 9p

Communication parameters

Signal level RS-232C compliant

Synchronization method Asynchronous

Baud rate 9600 bps

Parity None

Character length 8 bits

Stop bit 1 bit

Flow control -

Signal names for D-sub 9P connector

Pin No. Details

R X D

T X D

GND

•

Non use

(Shorted in this set)

•

These signal names are those of computer speciﬁ cations.

Connections

Command

Command Parameter Control details

PON None Power ON

POF None Power OFF

AVL ** Volume 00 - 63

AMT

0 Audio MUTE OFF

1 Audio MUTE ON

IMS None

SL1

SL2

SL3

PC1

SL1A

SL1B

SL2A

SL2B

Input select (toggle)

Slot1 input

Slot2 input

Slot3 input

PC input

Slot1 input (INPUT1A)

Slot1 input (INPUT1B)

Slot2 input (INPUT2A)

Slot2 input (INPUT2B)

DAM None

ZOOM

FULL

JUST

NORM

SELF

ZOM2

ZOM3

SJST

SNOM

SFUL

14:9

Screen mode select (toggle)

Zoom1

(For Video/SD/PC signal)

16:9

Just (For Video/SD signal)

4:3 (For Video/SD/PC signal)

Panasonic Auto (For Video singal)

Zoom2 (For HD signal)

Zoom3 (For HD signal)

Just (For HD signal)

4:3 (For HD signal)

4:3 Full (For HD signal)

14:9

With the power off, this display responds to PON command

only.

(Male)

(Female)

Note: To use serial control for this unit, make sure to set the “Control I/F Select” in the “Network Setup” menu to

“RS-232C”. (see page 53)

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 65 66

Comments to this Manuals

No comments

Panasonic TH85PF12E User Manual Page 10

Comments to this Manuals

Related products and manuals for Plasma TVs Panasonic TH85PF12E