Panasonic WVBL730_SERIES Operations Instructions

CCTV CamerasWV-BLR730/WV-BLR734(Lens : option)Before attempting to connect or operate this product,please read these instructions completely.FRANÇAIS

-8-• Calculation method of maximum cable lengthbetween camera and power supply.10.5 V DC ≤ VA − (R x 0.42 x L) ≤ 16 V DCL : Cable length (meter)R :

-9-Video Cable1. It is recommended to use a monitor whose resolu-tion is at least equal to that of the camera.2. Set the termination switch to the 75

-10-Note:Use the cable that is described below for RS485site communication.• Shielded, two twisted pairs cable• Low impedance• Wire gauge size is thic

-11-SYSTEM CONNECTIONa) Single Camera Connection (RS485Interface Model/Half Duplex)b) Daisy Chain Connection (RS485Interface Model/Half Duplex)WV-BLR7

-12-Installation of Auto Iris Lens ConnectorInstall the lens connector (YFE4191J100) when using avideo drive ALC lens.The installation should be made

Caution for Mounting the LensThe lens mount should be a C-mount or CS-mount (1”-32UN) and the lens weight should be less than 450 g(0.99 lbs). If the

The following adjustment should be made by qualifiedservice personnel or system installers.1. Loosen the screws on the flange-back adjustingring.2. Tu

• Mounting from the bottomThis camera is designed to be mounted from thebottom, as shown below. The mounting hole is astandard photographic pan-head s

-16-1. Camera Setup MenuThis camera utilizes a user setup menu that is dis-played on-screen.The setup menu contains various items that form atree-type

-17-MotionDetectorON/OFFLens DriveSignalSelectionDC VideoSpecialmenuDetectionLevelAdjustmentDetectionMasking AreaSelectionUpsidedownAPGainPede

CAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION: TO REDUCE THE RISK OF ELECTRICSHOCK, DO NOT REMOVE COVER (ORBACK), NO USER SERVICEABLE PARTSINSIDE.

-18-Left ButtonSet SwitchRight ButtonDown ButtonUp ButtonUp Button (): This button is used to move thecursor upwards. Use this button toselect an item

-19- ** CAM SET UP **CAMERA ID OFF ALC/ELC ALC SHUTTER OFFAGC ONSENS UP OFFSYNC INTMOTION DET OFF LENS DR

-20- ** SPECIAL **UP SIDE DOWN OFFAP GAIN ...I...PEDESTAL .I... - +CAMERA RESET PUSH SWRET END• Editing the

-21-SETTING PROCEDURESUNIT NUMBERThis item is used to select the camera number that isused with RS485 communication.1. Move the cursor to the paramete

-22-X ON/X OFFThis item is used to select applying the flow control ornot.1. Move the cursor to the X ON/X OFF parameter.2. Select NOT USE (not apply

0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().,'":;&#!?= +-*/%$ÄÜÖÆÑÅ SPACE POSI RET END RESET ...-23-● CAMERA Se

-24-2. Move the pointer to the character to be edited bypressing or . Then move the cursor to thecharacter area and select a new character.3. Press

-25-2-1. ALC Mode with PRESET ONIn normal use, the important object in a scene isplaced in the center of the monitor’s screen. In the fac-tory setup m

-26- ** ALC CONT ** BACK LIGHT COMPPRESET OFFMASK SET LEVEL ...I... - +RET END ** ALC CONT ** BACK LIGHT

-27-Blinking2. Move the cursor to MASK SET and press .The 48 mask areas appear on the monitor screen.The cursor is blinking in the top left corner of

CONTENTSPREFACE ... 2FEATURES ...

-28-3. Shutter Speed Setting (SHUTTER)Note: If ELC is selected, this item is not available.You can select an electronic shutter speed of 1/50(OFF), 1/

-29-4. Gain Control Setting (AGC ON/OFF)You can set the gain (brightness level portion of animage) to automatic level adjustment (ON) or fixedlevel (O

-30-Important Notices:1. The priority for the sync modes is as follows.1. Multiplexed Vertical Drive (VD2) (Highest pri-ority)2. Line-lock (LL)3. B/W

-31-4. After confirming the cursor is on EXT (VS), press. The phase adjustment menu appears on themonitor.6-1. VS Gen-lock Mode (EXT(VS))1. Move the c

-32-2. After confirming the cursor is on LL, press .The vertical phase adjustment menu appears onthe monitor.3. Move the cursor to COARSE. The cursor

-33-• To reset COARSE and FINE to the values pre-set at the factory, press or simultane-ously. COARSE and FINE adjustments arepreset at the factory

-34-1. Move the cursor to the LENS DRIVE parameter.2. Select DC if you are using the auto iris lens thatrequires a DC drive signal.Select VIDEO if you

-35-9. Special Menu (SPECIAL)This menu lets you adjust and setup the video signal ofthe camera to meet your requirements.Move the cursor to RET on the

-36-When the camera is aimed at a bright light, such as aspotlight, or a surface that reflects bright light, smearor blooming may appear. Therefore,

Pick-up Device: 771 (H) x 582 (V) pixels, Frame Interline Transfer CCDScanning Area: 6.4 (H) x 4.8 (V) mm (Equivalent to scanning area of 1/2” pick-up

1. The following functions are built in.(1) Auto Light Control (ALC)/Electronic LightControl (ELC)(2) Back Light Compensation (Auto: Factory pre-set,

-38-Power Source and WV-BLR730: 220 - 240 V AC 50 Hz, 5.5 WPower Consumption: WV-BLR734: 24 V AC 50 Hz, 5.6W12 V DC, 600 mADimensions (without lens):

Matsushita Electric Industrial Co., Ltd.Central P.O. Box 288, Osaka 530-91, JapanN0898-0 YWV8QA5031AN Printed in JapanInprimé au JaponN 30

1. Do not attempt to disassemble the camera.To prevent electric shock, do not remove screwsor covers.There are no user serviceable parts inside. Ask a

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS-4-Hi-Z G/L 75Ω<WV-BLR730><WV-BLR734>CCDCCDVIDEO OUTPOWERRS485(A)(B)GND220 - 240 V~50HzGEN-L

q Auto Iris Lens ConnectorThis connector is used to connect with the auto irislens by a 4-pin male connector that is supplied asa standard accessory (

!3 Video Output Connector (VIDEO OUT)This connector is used to connect with the VIDEOIN connector of the monitor.!4 Power Cord SocketThis socket is us

Copper wire #24 #22 #20 #18size (AWG) (0.22mm2) (0.33mm2) (0.52mm2) (0.83mm2)Resistance 0.078 0.050 0.030 0.018Ω/mResistance 0.026 0.017 0.010 0.006Ω/