Panasonic DMREX99V User Manual download pdf (Page 97)

VQT2J45

Digital broadcasts cannot be received.

¾ Check the connections. (> 10, 11, 86)

¾ Digital broadcast may not have started in your region yet.

¾ The aerial may not be pointing in the direction of the TV

station, or the direction of the aerial may have changed due

to strong winds or vibration. If problem persists consult your

local TV aerial installer.

¾ Perform “DVB Auto Setup by Signal Quality” in the Setup

menu. (> 79)

TV reception worsens after connecting the unit.

¾ This can occur because the signals are being divided

between the unit and other equipment. It can be solved by

using a signal booster, available from electronics retailers.

After “DVB Auto Setup by Signal Quality” or “DVB

Auto Setup by Region” only some or no DVB

channels are found.

¾ Check to ensure your area is covered by DVB

transmissions.

¾ Check that the aerial and antenna cable are designed for

DVB.

¾ Perform “DVB Auto Setup by Signal Quality” in the Setup

menu. (> 79)

Picture regularly breaks up on some channels, “No

Signal” message is displayed.

Check “Signal Condition”. If “Signal Quality” or “Signal Strength”

are displayed in red or constantly changing, check aerial. If

problem persists consult your local TV aerial installer. (

79)

Check that the aerial and antenna cable are designed for DVB.

¾ Interference (known as impulse noise) from household

appliances such as light switches, fridges, etc. may cause

picture break up and/or audio distortion. Use a high quality

quad shielded coaxial cable fly lead between this unit and

antenna wall socket to minimise impulse noise pickup. If

problem persists consult your local TV aerial installer.

¾ Check aerial connection.

¾ Adjust the aerial reception with “DVB Manual Tuning”.

(> 79)

¾ Perform “DVB Auto Setup by Signal Quality” in the Setup

menu. (> 79)

Picture very infrequently breaks up on some or all

channels.

¾ Electrical atmospheric interference caused by local or

distant lightning storms or heavy rain with wind in “leafy”

locations may cause pictures to break up and audio to mute

or distort momentarily.

¾ Impulse noise interference from an infrequently used

electrical appliance, or a passing vehicle or lawn mower

with a “noisy” ignition system.

¾ Perform “DVB Auto Setup by Signal Quality” in the Setup

menu. (> 79)

Unusual station sorting.

¾ The station sorting of this unit is pre-defined. Use

Favourites to sort the stations as you want them. (> 78)

The digital channel information does not appear.

¾ Select the length of time (3–10 sec.) in the “On-Screen

Messages” in the Setup menu. (> 81)

¾ The digital channel information will not appear during

playback or recording.

¾ Perform “DVB Auto Setup by Signal Quality” in the Setup

menu. (> 79)

No Digital Teletext

¾ Not all functions of Digital Teletext work on this unit.

¾ When subtitle is on or additional information in the digital

channel information is displayed, Digital Teletext does not

work.

¾ Perform “DVB Auto Setup by Signal Quality” in the Setup

menu. (> 79)

After the Auto-Setup, there aren’t any stations in the

station list although found stations were displayed

during Auto-Setup.

¾ “Shipping Condition” was performed or the unit was in the

delivery status. The Auto-Setup was then started and

interrupted.

Do an Auto-Setup again and let it continue right through to

the end.The data is only saved after this has been

completed.

The Signal Strength is over 100% (> 10)

¾ Reduce the signal amplification at your aerial. (> 79)

After performing an update, you can no longer

receive broadcasts.

¾ Depending on the content of the software update, some

settings may have returned to the preset values.

Perform “Shipping Condition” in the Setup menu and then

set the channel. (> 79, 84)

VIERA Link doesn’t work.

¾ Check the HDMI cable connection. Check that “HDMI” is

displayed on the front display when the unit is powering on.

¾ Make sure that “VIERA Link” is set to “On”. (> 82)

¾ Check the “HDAVI Control” settings on the connected

device.

¾ Some functions may not work depending on the version of

“HDAVI Control” of the connected equipment. This unit

supports “HDAVI Control 5” function.

¾ If the connection for the equipment connected with an

HDMI cable was changed, or if there was a power failure or

the plug was removed from the household mains socket,

“HDAVI Control” may not work. In this case, perform the

following operations.

1 When the HDMI cable is connected to all equipment with

the power on, turn the TV (VIERA) on again.

2 Change the TV (VIERA) settings for the “HDAVI Control”

function to off, and then set to on again. (For more

information, see the VIERA operating instructions.)

3 Switch the VIERA input to HDMI connection with this

unit, and after this unit’s screen is displayed, check that

“HDAVI Control” is working.

The Control Panel does not appear.

¾ The control panel is only displayed when connected to a TV

with “HDAVI Control 2” or later function. (> 49)

The operation on this unit (music playback etc.) is

interrupted.

¾ The operation on this unit may be interrupted when you

press buttons on the TV remote control that do not work for

VIERA Link functions.

General Issues: DVB-T

General Issues: VIERA Link

DMR-EX99VEB_VQT2J45.book 97 ページ２０１０年１月７日　木曜日　午後１時４１分

1 2 ... 92 93 94 95 96 97 98 99 100 101 102 ... 107 108

Comments to this Manuals

No comments

Panasonic DMREX99V User Manual Page 97

Comments to this Manuals

Related products and manuals for DVD players Panasonic DMREX99V