Panasonic SCBT200 Operations Instructions download pdf (Page 48)

RQT9510

Troubleshooting guide

Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions

indicated in the chart do not solve the problem, consult your dealer for instructions.

The following do not indicate a problem with this unit:

≥Regular disc rotating sounds.

≥Image disturbance during search.

To reset this unit Page

Power

Operation

To restore the unit if it freezes

due to one of the safety

devices being activated

≥Press and hold [Í/I] on the main unit for 3 seconds. (The settings remain

unchanged.)

—

To return all settings other

than some settings to the

factory preset

≥Select “Yes” in “Default Settings” in the Setup menu.

This returns all values in the Setup menu and the on-screen menu, except for

“Remote Control”, “On-Screen Language”, “IP Address / DNS Settings”, “Proxy

Server Settings”, “DVD-Video Ratings”, “BD-Video Ratings” and “Network Service”

to the default settings.

To return to the factory

preset

(No setting)

≥Reset the unit as follows:

1Press [Í/I] on the unit to turn off the unit.

2 Press and hold [5/9] and press [Í/I] and [< OPEN/CLOSE] on the unit at

the same time for more than 5 seconds until “PLEASE WAIT” is displayed on

the unit.

3 The power is turned on and then turned off automatically.

—

No power. ≥Insert the AC mains lead securely into a household mains socket. 13

The unit switches to

standby mode.

≥When the time set for the sleep timer has passed, the power will be turned off.

≥One of the unit’s safety devices is activated. Press [Í/I] on the main unit to turn

the unit on.

—

Power of this unit is turned

off when the input for the

TV is changed.

≥If connected with an HDAVI Control 4 compatible TV (VIERA) with the “Intelligent

Auto Standby” setting activated on the TV, when switching the TV input, the unit

will be automatically turned to standby if the TV audio is not output from the unit’s

speakers. For details please read the operating instructions of the TV.

The remote control doesn’t

work properly.

≥The remote control and main unit are using different

codes. Change the code on the remote control.

Press and hold [OK] and the indicated number button

at the same time for more than 5 seconds.

≥The batteries are depleted. Replace them with new ones.

≥It may be necessary to set the code of the remote control again after changing the

batteries for remote control.

≥You are not pointing the remote control at the main unit’s remote control signal

sensor during operation.

≥Coloured glass may obstruct the signal reception/transmission.

≥

Don’t place the signal sensor in direct sunlight or in areas that may be subject to sunlight exposure.

5, 51

—

The unit is on but cannot be

operated.

≥Confirm the correct drive is selected.

≥Some operations may be prohibited by the disc.

≥The unit is hot (“U59” appears on the display). Wait for “U59” to disappear.

≥One of the unit’s safety devices may have been activated.

Reset the unit as follows:

1Press [Í/I] on the main unit to switch the unit to standby.

If the unit doesn’t switch to standby, press and hold [Í/I] on the main unit for

about 3 seconds. The unit is forcibly switched to standby.

Alternatively, disconnect the AC mains lead, wait one minute, then reconnect it.

2Press [Í/I] on the main unit to switch it on. If the unit still cannot be operated,

consult the dealer.

≥Condensation has formed. Wait 1 to 2 hours for it to evaporate.

—

Play fails to start even when

[1PLAY] is pressed.

Play starts but then stops

immediately.

≥Insert the disc correctly with the label facing up.

≥The disc is dirty.

≥You tried to play a blank media or unplayable media on this unit.

≥

[DivX] If playing DivX VOD content, refer to the homepage where you purchased it.

≥The producers of the disc can control how discs are played. So you may not

always be able to control play as described in these operating instructions. Read

the disc’s instructions carefully.

44, 45

—

Cannot eject disc. ≥The unit may have a problem. While the unit is off, press and hold [5/9] and

[< OPEN/CLOSE] on the main unit at the same time for about 5 seconds.

Remove the disc and consult the dealer.

—

Startup is slow.

It takes time before play

starts.

≥Startup takes time in the following situations.

–Immediately after a power failure or the AC mains lead is connected.

–When the unit is connected with an HDMI cable.

—

Played back image is

distorted or does not

playback correctly. (

[AVCHD])

≥High definition video (transfer rate of 18 Mbps or faster) cannot be played back

correctly if it was recorded on a DVD compatible to double speed or slower.

—

Cannot set “On” in “24p

Output”.

≥Only when the unit is connected to the HDMI terminal of a TV supporting 24p you

can select “On”.

Reference

SCBT200&205EB_RQT9510-B.book 48 ページ２００９年５月２１日　木曜日　午後５時２２分

1 2 ... 43 44 45 46 47 48 49 50 51 52 53 ... 59 60

Comments to this Manuals

No comments

Panasonic SCBT200 Operations Instructions Page 48

Comments to this Manuals

Related products and manuals for Home cinema systems Panasonic SCBT200