Panasonic MN103001G/F01K User Manual Page 298
- Page / 466
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Watchdog Timer
12-6
3 — When this bit is read, a "0" is returned.
4 WDOVF The value of the watchdog timer overflow output.
5 WDOVT Watchdog timer overflow output selection
0: Pulse output
1: Level output
6 WDRST Binary counter reset, watchdog timer overflow output (WDOVF flag) reset
0: No reset
1: Reset
When a "1" is written to this bit, the reset pulse is generated for the width of
one clock pulse, and then this bit returns to "0". "0" is returned whenever
this bit is read.
7 WDCNE Watchdog timer count operation control flag
0: Count operation stopped
(oscillation stabilization wait operation is possible)
1: Count operation enabled
[Notes]
1. When resetting the value of watchdog overflow by writing the WDRST flag, do not simultaneously
overwrite the WDOVT flag.
If this flag is overwritten, the value of watchdog overflow reset is not guaranteed.
2. When changing the values of WDCK2 to 0, first stop the watchdog timer and reset the counter.
Reset control register
Register symbol: RSTCTR
Address: x'34004004
Purpose: This flag causes the program to generate an internal reset.
Bit No. 76543210
Bit
-------
CHIP
name RST
Reset 00000000
Access RRRRRRRR/W
Bit No. Bit name Description
0 CHIPRST This flag is used to generate a self-reset (an internal reset of the chip due to an
internal cause). A self-reset is generated when this flag is overwritten from "0" to
"1".
A self-reset is not generated if this flag is already set to "1" when it is written with
a "1".
The value stored in this flag is retained even after the reset.
The CHIPRST flag is cleared either by an external reset signal (RST) or by writing
a "0" to this flag through the software.
- MN103001G/F01K 1
- LSI User’s Manual 1
- Table of Contents 10
- 7. Internal Memory 11
- 8. Bus Controller (BC) 11
- 9. Interrupt Controller 12
- 10. 8-bit Timers 12
- 11. 16-bit Timers 13
- 12. Watchdog Timer 13
- 13. Serial Interface 13
- 14. A/D Converter 14
- 15. I/O Ports 14
- 16. Internal Flash Memory 15
- 17. Ordering Mask ROM 15
- Appendix 15
- List of Figures and Tables 16
- List of Tables 23
- 1. General Specifications 27
- 1.1 Overview 28
- 1.2 Features 28
- _____________ 29
- TOP VIEW 31
- General Specifications 32
- Table 1-4-1 Pin Assignments 32
- 2.2 Block Diagram 37
- 2.3 Programming Model 38
- LD EXT DROM ROM 42
- USE WAIT W WAIT 42
- Reset 00000 0000 000 0 00 0 43
- 2.4 Instructions 44
- 2.5 Interrupts 48
- 1413121110987654321 51
- 3 Cycles 54
- Operation extension interface 58
- 3.2 Extension Instructions 59
- Bit 31 Bit 0 60
- 10000000000000000 83
- Dm[31:24] 84
- Dm[23:16] Dm[15:8] Dm[7:0] 84
- Multiply-and 88
- MCRH, MCRL access instruction 89
- 4. Memory Modes 97
- MN103001G 99
- /MN1030F01K 99
- Memory Modes 102
- 5. Operating Mode 103
- 5.1 Overview 104
- 5.2 Reset Mode 105
- 5.3 Low Power Mode 106
- 6. Clock Generator 107
- 6.1 Overview 108
- 6.2 Features 108
- 6.3 Block Diagram 108
- 6.4 Description of Operation 109
- SYSCLK MCLK IOCLK 110
- 7.1 Overview 112
- 7.2 Features 112
- CPU core 113
- Internal Memory 114
- 8.1 Overview 116
- 8.2 Features 116
- 8.3 Bus Configuration 117
- 8.4 Block Diagram 117
- 8.5 Pin Functions 119
- 8.6 Description of Registers 121
- Settings other than those 122
- CAO (ADE)+CAS (REN) 127
- ≥ WEN 11111: 31MCLK 127
- Reset 1 1 11111111111111 137
- 31 30 29 28 27 26 25 24 23 22 140
- External address (8 MB space) 140
- Extension address 140
- Bus Controller (BC) 141
- Processor mode 141
- Extension memory mode 141
- 8.8 Operation Clocks 142
- 8.9 Mode Settings 142
- 4 2 1 1/2 143
- Internal Read 143
- 6 to 9 6 to 9 6 to 9 6 143
- 8.11 Store Buffer 144
- DK detection start 149
- Consumed internally 157
- Consumed internally by the BC 157
- “Description of Registers.” 164
- A[0]=1 data outdata outA[0]=0 167
- “0”( )“L” 167
- “0”(“L”) 168
- “0” (“L”) 175
- Row Column ColumnRow 178
- Refresh count value 183
- 8.15 Bus Arbitration 184
- 8.16 Cautions 187
- 9.1 Overview 190
- 9.2 Features 190
- 9.3 System Diagram 190
- 9.4 Block Diagram 191
- Interrupt control 192
- 9.5 Description of Registers 194
- Bit No.1514131211109876543210 198
- 9.6 Description of Operation 218
- Interrupt Controller 220
- 10.1 Overview 222
- 10.2 Features 222
- 10.3 Block Diagram 223
- 8-bit Timers 224
- 10.4 Functions 229
- 10.5 Description of Registers 230
- Bit No.76543210 237
- Reset 0 0 0 0 0 0 0 0 237
- 10.6 Description of Operation 240
- TMnBR value TMnBR value-1 245
- 10.6.3 Cascaded Connection 246
- TM0BR value 250
- TM0BR value-1 250
- TM1BR value 250
- TM1BR value - 1 250
- 11.1 Overview 256
- 11.2 Features 256
- 11.3 Block Diagram 257
- 16-bit Timers 258
- I/O port block 259
- Timer 13 259
- Timer 12 259
- Timer 11 259
- Timer 10 259
- (TM10CB) 260
- 11.4 Functions 261
- 11.5 Description of Registers 262
- TM10CA valueTM10CA value-1 273
- TM10CA value-2 273
- Pin input 274
- (TM10IOA) 274
- TM10BC overflow 276
- Don' t Care 277
- TM10BC value 281
- TM10CNE flag 281
- Change in the value 283
- TMnBR value -1 291
- 12.1 Overview 294
- 12.2 Features 294
- 12.3 Block Diagram 295
- 12.4 Description of Registers 296
- (n + WDCK x 2) 299
- Watchdog Timer 300
- SYSCLK 255-cycle width 301
- 13.1 Overview 304
- I/O Port Block 307
- Interrupt request 313
- Bi-directional transfer 316
- Undirectional transfer 316
- Start sequence resend 325
- Serial interface n 327
- (n = 1, 2) 327
- Serial interface 3 339
- Bit No. 7 6 543210 345
- Reset 0 0 000000 345
- Access RRRRRRRR 345
- Serial Interface 349
- 10-bit sequential 356
- Selector 356
- 14.2 Features 357
- 14.3 Block Diagram 358
- 14.4 Description of Registers 359
- 14.5 Description of Operation 361
- ■ Operating mode selection 361
- Sampling cycle 365
- 15.1 Overview 368
- 15.2 Port 0 372
- Access R R R R R R/W R/W R/W 373
- 15.3 Port 1 376
- I/O Ports 377
- 15.4 Port 2 381
- 15.5 Port 3 385
- 15.6 Port 4 388
- I/O Ports 390
- Access R R R/W R/W R/W R R R 393
- 15.7 Port 5 395
- Bit No. 76543210 402
- Reset 00111111 402
- 15.8 Port 6 404
- 15.9 Port 7 407
- Bit name ----P73S - - 409
- Access RRRRR/WRRR 409
- 15.10 Port 8 411
- 15.11 Port 9 414
- Reset 01100000 417
- 15.12 Port A 419
- 15.13 Port B 423
- 15.14 Port C 427
- Pin name Treatment 430
- 16.1 Overview 432
- 16.2 Features 432
- 16.3 Block Diagram 432
- Internal Flash Memory 435
- Internal Flash Memory 436
- Table 16-5-2 Pin Functions 436
- 16.6 On-board Write Mode 438
- 17.1 Overview 440
- Ordering Mask ROM 441
- Ordering Mask ROM 442
- Appendix-2 444
- Appendix-3 445
- Appendix-4 446
- Appendix-5 447
- Appendix B. Instruction Set 447
- Appendix-6 448
- Appendix-7 449
- Appendix-8 450
- Appendix-9 451
- Appendix-10 452
- Appendix-12 454
- Appendix-13 455
- Corrections 458
- Note) n= 0, 1, 2, 3 462
- LSI User's Manual 465
- SALES OFFICES 466
Related products and manuals for Computers Panasonic MN103001G/F01K
Computers Panasonic CF-31 User Manual
(40 pages)
(40 pages)
Computers Panasonic CF-T2 User Manual
(40 pages)
(40 pages)
Computers Panasonic CF-Y7 series User Manual
(44 pages)
(44 pages)
Computers Panasonic CF-47 User Manual
(36 pages)
(36 pages)
Computers Panasonic CF-T1 User Manual
(72 pages)
(72 pages)
Computers Panasonic CF-18 User Manual
(130 pages)
(130 pages)
Computers Panasonic KX-TDE User Manual
(16 pages)
(16 pages)
Computers Panasonic KXP7100 User Manual
(115 pages)
(115 pages)
Computers Panasonic KXP7100 User Manual
(4 pages)
(4 pages)
Computers Panasonic CF-48 User Manual
(38 pages)
(38 pages)
Computers Panasonic CF-E1M User Manual
(64 pages)
(64 pages)
(12 pages)
Computers Panasonic CF-27 User Manual
(28 pages)
(28 pages)
Computers Panasonic CF-18 User Manual
(44 pages)
(44 pages)
© 2020, manymanuals.com. All rights reserved. | 0.697 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals