Panasonic SC-RT50 User Manual download pdf (Page 34)

RQT8655

The radio

Preparation

pTurn off TV while using radio since noise may occur.

pPress [THEATER] to switch the remote control to operate this unit.

Press [FM/AM] to select the “FM” or “AM”.

2 Press [] or [



] to select the

frequency of the required station.

TUNED: Displayed when a radio

station is tuned.

ST:

Displayed when a stereo FM

broadcast is being received.

Press and hold [



] or [



] until the frequency starts scrolling

to start automatic tuning. Tuning stops when a station is found.

Adjust the volume with [

A B

VOLUME].

w If noise is excessive

Press [FM MODE].

Each time you press the button:

FM: Changes between stereo and forced monaural.

AM: BP1 BP2  BP3  BP4 (BPNBeat Proof)

$

Select between BP1 and BP4 that receives good reception.

The FM mode is cancelled when you change the frequency.

w FM frequency step

The step is factory-set to 0.2 MHz, but you can change it to receive

broadcasts allocated 0.1-MHz steps.

1 Press [FM/AM] to select “FM”.

2 Press and hold [w] on the main unit.

After a few seconds the display changes to show the current

minimum frequency. Continue to hold the button down. The

minimum frequency changes and the step is changed.

To return to the original step, repeat the above steps.

[Note]

Any FM/AM frequencies preset in channels will be changed by this

procedure. Preset them again.

Preset channels to make selection simple.

Up to 30 stations can each be set in the FM and AM bands.

Press [FM/AM] to select the “FM” or “AM”.

2 Press [] or [] to tune to the

lowest frequency.

FM: 87.9 MHz or 87.5 MHz

AM: 520 kHz

3 Press and hold [ENTER].

Release the button when “AUTO FM” or “AUTO AM” is lit on

the display.

The tuner presets all the stations it can receive into the

channels in ascending order.

p“SET OK” is displayed when the stations are set. The last

station to be set is then played.

pThe unit of display is MHz for FM radio and kHz for AM radio when

the selector is in FM/AM mode.

p“ERROR” is displayed

Presetting was unsuccessful. Preset manually.

1 Tune to the station (

➡

left).

2 Press [ENTER].

While “MEMO” is flashing on the display

Press the numbered buttons or [

CH]

to select a channel and press [ENTER].

e.g., “2”: [0] ➡ [2]

“12”: [1] ➡ [2]

The station occupying a channel is erased if another station is preset

in that channel.

1 Press [FM/AM] to select “FM” or “AM”.

2 Press the numbered buttons or

[9:CH] to select the channel.

e.g., “2”: [0] ➡ [2]

“12”: [1] ➡ [2]

[Note]

If there is nearby electrical interference during auto tuning the

frequency may come to a halt without locating a channel. Turn off the

power of the nearby electrical equipment.

w Use FM outdoor antenna if radio reception is

poor.

pDisconnect the FM indoor antenna.

pThe antenna should be installed by a competent technician.

[Note]

pDisconnect the outdoor antenna when the unit is not in use.

pDo not use the outdoor antenna during an electrical storm.

Manual tuning

SRD MUSIC

Numbered

buttons

9:CH

THEATER

, 

ABVOLUME

■

H.BASS

SRD ENH

SURROUND MUSIC

SFC/EQ

C. FOCUS,

FM MODE

SRD MUSIC

, , , 

ENTER

ABVOLUME

9:CH

FM/AM

Preset tuning

Automatic presetting

Manual presetting

Selecting channels

75 j coaxial cable

(not included)

Antenna plug

(not included)

Back of

the main unit

FM outdoor antenna

(Using a television

antenna)

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 51 52

Comments to this Manuals

No comments

Panasonic SC-RT50 User Manual Page 34

Comments to this Manuals

Related products and manuals for Acoustics Panasonic SC-RT50