Panasonic PT-DS8500U Operations Instructions Page 64
- Page / 129
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
ADVANCED MENU
64
- ENGLISH
Settings
INPUT RESOLUTION
Input resolution adjustment achieves the best image
when the screen ickers or halo is observed around
the contour. Set the values appropriately for the signal
resolution that is being used.
Press ▲▼ to select [INPUT 1 )
RESOLUTION].
Press <ENTER> button.2 )
The [INPUT RESOLUTION] screen will be
z
displayed.
Press ▲▼ to select [TOTAL DOTS], 3 )
[DISPLAY DOTS], [TOTAL LINES] or
[DISPLAY LINES], and the press ◄►
to adjust it.
Each item automatically displays a value in
z
response to the type of the input signal. If
vertical stripes appear on the screen or the
image is partly missing, increase or decrease
the displayed value while observing the screen
to achieve the optimal value.
Note
The vertical stripes will not appear on the all white signal
z
image.
The picture may be distorted during the adjusting
z
operation, but this is not a fault.
The [INPUT RESOLUTION] can be adjusted only when
z
RGB signal input is applied with RGB1 and RGB2 IN.
CLAMP POSITION
Use the clamp position adjustment to achieve the
optimal value when dark areas of the image are
crushed or displayed in green.
Press ▲▼ to select [CLAMP 1 )
POSITION].
Press ◄► to adjust.2 )
The value changes from 1 to 255.
z
The optimal value for the clamp position
z
adjustment
If dark areas are crushed :
The optimal value is the point where the dark
area is best improved.
If the dark areas are displayed in green :
The optimal value is the point where the green
areas become black and the crushing effect is
rectied.
Note
The [CLAMP POSITION] can be adjusted only when the
z
RGB signal input is applied with RGB1 and RGB2 IN.
The [CLAMP POSITION] may not be adjusted, depending
z
on the signal.
EDGE BLENDING
The built-in edge blending feature allows multiple
projector images to be seamlessly overlapped.
Press ▲▼ to select [EDGE 1 )
BLENDING].
Press ◄► to switch [EDGE 2 )
BLENDING].
The setting will change as follows each time
z
◄► is pressed.
OFF ON USER
OFF
When the multi-screens are not
going to be used.
ON
When the default linear blending
ramps are sufcient.
USER
When a user-dened blending
ramp is required. These ramps can
be dened and uploaded to the
projector through the RS-232 port.
Consult your dealer for details.
Press <ENTER> button.3 )
The [EDGE BLENDING] screen will be
z
displayed.
Press ▲▼ to specify the area to be 4 )
adjusted.
To blend the top edge:
z
set [UPPER] to [ON].
To blend the bottom edge:
z
set [LOWER] to
[ON].
To blend the left edge:
z
set [LEFT] to [ON].
To blend the right edge:
z
set [RIGHT] to [ON].
Press ◄► to toggle [ON] and [OFF].5 )
Press ◄► to adjust the overlap width 6 )
and the starting point.
- Operating Instructions 1
- PT-DZ8700U 1
- PT-DS8500U 1
- PT-DW8300U 1
- Important Safety Notice 2
- Heightened luminance 4
- Lengthened lamp 4
- Reduced standby power 4
- Contents 5
- Maintenance 7
- Appendix 7
- - ENGLISH 10
- Cautions when transporting 11
- Cautions when installing 12
- ENGLISH 13
- Security 14
- Cautions on use 14
- Cleaning and maintenance 15
- Disposal 15
- Accessories 16
- About Your Projector 17
- Projector body 18
- Setting projector ID number 20
- Using a wired remote control 20
- Setting up 21
- Connections 34
- How to remove the projection 37
- Powering ON/OFF 38
- Powering up the projector 39
- Making adjustment and 39
- Powering off the projector 40
- Direct power off function 40
- Projecting 41
- Using the SHUTTER function 46
- On-screen display function 46
- Switching the input signal 46
- STATUS function 46
- Automatic adjustment 47
- Using the FUNCTION button 47
- Displaying the internal 47
- Changing the picture aspect 48
- Menu Navigation 49
- MAIN MENU 50
- SUB MENU 50
- PICTURE menu 52
- CONTRAST 53
- BRIGHTNESS 53
- COLOR TEMPERATURE 54
- SYSTEM DAYLIGHT VIEW 55
- SHARPNESS 56
- NOISE REDUCTION 56
- DYNAMIC IRIS 56
- (PT-DZ8700U/PT-DS8500U only) 57
- POSITION menu 58
- (PT-DZ8700/PT-DS8500 only) 60
- (PT-DW8300 only) 62
- ADVANCED MENU 63
- INPUT RESOLUTION 64
- CLAMP POSITION 64
- EDGE BLENDING 64
- FRAME DELAY 66
- RASTER POSITION 66
- DISPLAY LANGUAGE menu 67
- DISPLAY OPTION menu 68
- (PT-DZ8700 only) 70
- AUTO SIGNAL 71
- AUTO SETUP 71
- (Only RGB input) 72
- BACK COLOR 74
- STARTUP LOGO 74
- PROJECTOR SETUP menu 75
- COOLING CONDITION 76
- LAMP SELECT 76
- LAMP RELAY 76
- LAMP POWER 77
- BRIGHTNESS CONTROL 77
- STANDBY MODE 81
- SCHEDULE 81
- NO SIGNAL SHUT-OFF 84
- REMOTE2 MODE 84
- FUNCTION BUTTON 84
- DATE AND TIME 84
- LENS CALIBRATION 85
- FILTER COUNTER RESET 85
- LOAD ALL USER DATA 86
- INITIALIZE 86
- SERVICE PASSWORD 86
- SAVE ALL USER DATA 86
- P IN P menu 87
- TEST PATTERN menu 88
- SIGNAL LIST menu 89
- Managing the sub memory 90
- SECURITY menu 91
- DISPLAY SETTING 92
- TEXT CHANGE 92
- MENU LOCK 92
- MENU LOCK PASSWORD 92
- CONTROL DEVICE SETUP 93
- Network connections 95
- NETWORK menu 100
- Monitor Lamp indicators 107
- Replacement 109
- Troubleshooting 112
- Technical Information 114
- Control commands via LAN 115
- Serial terminal 117
- REMOTE 2 IN terminal 120
- List of compatible signals 122
- Specications 124
- Dimensions 126
- About brand 126
- Attachment procedure 127
- ヱㄏㄔㄐㄏㄊチヤㄐㄓㄑㄐㄓㄕㄊㄐㄏ 129
Related products and manuals for Data projectors Panasonic PT-DS8500U
(74 pages)
(62 pages)© 2020, manymanuals.com. All rights reserved. | 0.112 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals