Panasonic PT-DS8500U Operations Instructions Page 78
- Page / 129
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
PROJECTOR SETUP menu
78
- ENGLISH
Settings
When [MODE] is set to [AUTO]
Q
Press ▲▼ to select [LINK].5 )
Press ◄► to switch [LINK].6 )
The setting will change as follows each time
z
◄► is pressed.
OFF GROUP A
GROUP D GROUP C GROUP B
OFF
Brightness is corrected using the
brightness sensor of one of the
projectors, without linking with other
projectors.
A smaller [BRIGHTNESS CONTROL
GAIN] value means the constant
brightness can be maintained for longer.
GROUP
A - D
Brightness is corrected using brightness
sensors of multiple projectors linked
with each other.
Up to 4 groups from A to D can be set
within the same sub-network using
the network function that links multiple
projectors.
Up to 8 projectors can be registered in
1 group and linked with each other.
Press ▲▼ to select [APPLY].7 )
Press <ENTER> button.8 )
The selected [MODE] and [LINK] are activated,
z
then the [BRIGHTNESS CONTROL STATUS]
screen will be displayed.
If <ENTER> button is pressed while [MODE] of
z
the brightness control is not switched to [OFF],
the lamp power at the time is saved as the
reference power.
If <ENTER> button is pressed while [LINK] is
z
[GROUP A - D], the group name is displayed on
the screens of the projectors that are set in the
same group.
Note
When setting [MODE] of the brightness control to [AUTO]
z
or [PC], execute brightness control with the shutter open
for at least 2 minutes.
If the shutter is closed within about 10 minutes after
z
the lamp is turned on while the brightness control is set
to [MODE], [AUTO], or [PC], the brightness cannot be
measured. In this case, the brightness may be corrected
about 2 minutes after the shutter is opened.
While [MODE] of the brightness control is set to [AUTO]
z
or [PC], the [DYNAMIC IRIS] function is kept [OFF (No
correction)].
While [MODE] of the brightness control is set to [AUTO]
z
or [PC], the [LAMP POWER] is xed to [HIGH] or [LOW].
When changing the lamp power, return [MODE] of the
brightness control to [OFF], then change the lamp power
and adjust the brightness control again.
While [MODE] of the brightness control is set to [AUTO]
z
or [PC], the lamp power is measured automatically
about 8 minutes after the lamp is turned on and then
corrected so that the screen brightness will be the same
as the reference brightness when the brightness control
is executed. The lamp power is not measured for about
8 minutes after the lamp is turned on as it does not
stabilize within this period.
While [MODE] of the brightness control is set to [AUTO],
z
if the lamp is kept on for more than 25 hours, the
brightness is corrected automatically every 25 hours.
While [LAMP SELECT] is set to [DUAL] and [MODE]
z
is set to [AUTO], if the lamp goes off, the brightness is
corrected as much as possible about 1 minute after.
While [MODE] of the brightness control is set to [AUTO]
z
and [LINK] is set to [OFF], the brightness is corrected
until the maximum quantity of correction is achieved.
The brightness may be dispersed largely because of dust
z
sticking to the lens, screen, or inside of the projector,
depending on the environment in which the projector has
been installed.
If the brightness uctuates signicantly because of aging
z
of the lamp or if the lamp has been replaced, re-adjust
the brightness control.
J
BRIGHTNESS CONTROL STATUS
This function displays the status of the brightness
control.
Press ▲▼ to select [BRIGHTNESS 1 )
CONTROL STATUS].
Press <ENTER> button.2 )
The [BRIGHTNESS CONTROL STATUS]
z
screen will be displayed.
LINK GROUP A
- Operating Instructions 1
- PT-DZ8700U 1
- PT-DS8500U 1
- PT-DW8300U 1
- Important Safety Notice 2
- Heightened luminance 4
- Lengthened lamp 4
- Reduced standby power 4
- Contents 5
- Maintenance 7
- Appendix 7
- - ENGLISH 10
- Cautions when transporting 11
- Cautions when installing 12
- ENGLISH 13
- Security 14
- Cautions on use 14
- Cleaning and maintenance 15
- Disposal 15
- Accessories 16
- About Your Projector 17
- Projector body 18
- Setting projector ID number 20
- Using a wired remote control 20
- Setting up 21
- Connections 34
- How to remove the projection 37
- Powering ON/OFF 38
- Powering up the projector 39
- Making adjustment and 39
- Powering off the projector 40
- Direct power off function 40
- Projecting 41
- Using the SHUTTER function 46
- On-screen display function 46
- Switching the input signal 46
- STATUS function 46
- Automatic adjustment 47
- Using the FUNCTION button 47
- Displaying the internal 47
- Changing the picture aspect 48
- Menu Navigation 49
- MAIN MENU 50
- SUB MENU 50
- PICTURE menu 52
- CONTRAST 53
- BRIGHTNESS 53
- COLOR TEMPERATURE 54
- SYSTEM DAYLIGHT VIEW 55
- SHARPNESS 56
- NOISE REDUCTION 56
- DYNAMIC IRIS 56
- (PT-DZ8700U/PT-DS8500U only) 57
- POSITION menu 58
- (PT-DZ8700/PT-DS8500 only) 60
- (PT-DW8300 only) 62
- ADVANCED MENU 63
- INPUT RESOLUTION 64
- CLAMP POSITION 64
- EDGE BLENDING 64
- FRAME DELAY 66
- RASTER POSITION 66
- DISPLAY LANGUAGE menu 67
- DISPLAY OPTION menu 68
- (PT-DZ8700 only) 70
- AUTO SIGNAL 71
- AUTO SETUP 71
- (Only RGB input) 72
- BACK COLOR 74
- STARTUP LOGO 74
- PROJECTOR SETUP menu 75
- COOLING CONDITION 76
- LAMP SELECT 76
- LAMP RELAY 76
- LAMP POWER 77
- BRIGHTNESS CONTROL 77
- STANDBY MODE 81
- SCHEDULE 81
- NO SIGNAL SHUT-OFF 84
- REMOTE2 MODE 84
- FUNCTION BUTTON 84
- DATE AND TIME 84
- LENS CALIBRATION 85
- FILTER COUNTER RESET 85
- LOAD ALL USER DATA 86
- INITIALIZE 86
- SERVICE PASSWORD 86
- SAVE ALL USER DATA 86
- P IN P menu 87
- TEST PATTERN menu 88
- SIGNAL LIST menu 89
- Managing the sub memory 90
- SECURITY menu 91
- DISPLAY SETTING 92
- TEXT CHANGE 92
- MENU LOCK 92
- MENU LOCK PASSWORD 92
- CONTROL DEVICE SETUP 93
- Network connections 95
- NETWORK menu 100
- Monitor Lamp indicators 107
- Replacement 109
- Troubleshooting 112
- Technical Information 114
- Control commands via LAN 115
- Serial terminal 117
- REMOTE 2 IN terminal 120
- List of compatible signals 122
- Specications 124
- Dimensions 126
- About brand 126
- Attachment procedure 127
- ヱㄏㄔㄐㄏㄊチヤㄐㄓㄑㄐㄓㄕㄊㄐㄏ 129
Related products and manuals for Data projectors Panasonic PT-DS8500U
(74 pages)
(62 pages)© 2020, manymanuals.com. All rights reserved. | 0.977 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals