Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number
10PrecautionsRefer installation work to the dealer.Installation work requires technique and experi-ences. Failure to observe this may cause fire, elec
11Do not rub the edges of metal parts with your hand. Failure to observe this may cause injury. Do not touch this product, the power cord or the conne
12Code labelThe code labels (accessory) are required at inquiry for trouble. Use caution not to lose these labels. It is recommended to paste one of t
13Precautions for installationThis product is designed to be installed under eaves.Install the product under eaves to avoid direct sunlight.Installing
14Procure fixing screws separately. The screws that secure this product are not supplied. Prepare them according to the mate-rial and strength of the
15Major operating controlsDome cover* Do not touch the dome cover with your bare hands.EnclosureCamera fixing screwSD memory card slot coverNetwork ca
16About the [INITIAL SET] buttonAfter turning off the power of the camera, turn on the power of the camera while holding down this button, and wait fo
17When installing the camera on a ceiling or a wall, there are 3 methods as specified below. • Usingatwo-gangjunctionbox(☞ pages 18 and 19) •
18Using the side cable access hole SW458MWhen installing the camera directly on the ceiling or wall with cables exposed, cut out a portion of the encl
19Note: • Thedirectionof“gTOP” on the camera attachment (accessory) determines the upwards direc-tion of the image on the PC monitor. • Forcei
2The model number and serial number of this product may be found on the surface of the unit.You should note the model number and serial number of this
20Using the mount bracket (accessory) SW458Note: • Whenthecameraismountedontheceilingorwallwithaholeforcablerunning,orthecamerais
21x Determine the direction of the mount bracket according to the installation environment (how the cables are wired, etc.) before mounting it to a c
22<Using a conduit>Align the direction of the conduit to the direction of the female thread for the conduit on the mount bracket, and mount the
23c In the direction determined in x, fix the camera attachment (accessory) on the mount bracket using the fixing screws (accessory). (Recommended t
24IMPORTANT: • WheninsertinganSDmemorycard,makesurethedirection. • Before removing the SD memory card, select “Not use” for “SD
25Network cableM12 connector (male)Alarm input/output cable 4P alarm cable (accessory)LAN cable (category 5 or better)Power cable (12 V DC)2P power ca
26z Connect the microphone/line input cable and the microphone (for use of the audio reception function).Input impedance: 2 kΩ±10 %Recommended cable
27IMPORTANT:•InputandoutputoftheExternalI/Oterminal2and3canbeswitchedbyconfiguringthesetting. “Off” is selected by default. It is
28Waterproof treatment for the cable joint sectionsAdequate waterproof treatment is required for the cables when installing the camera with cables exp
29Connection example when connecting to a network using a PoE hub Powered speaker (option)Powered speaker (option)Microphone (option)Microphone (optio
3ContentsImportant safety instructions ... 4Limi
30Camera mountingInstallation shall be conducted after turning off each device.z Attach the camera attachment (accessory) on the ceiling or wall.<U
31Using the mount bracket SW458z Attach the camera onto the camera attachment (accessory) while aligning the “OPEN” mark of the camera with the projec
32x Engage the camera attachment fixing screws of the camera with the screw hole of the camera attachment (accessory) and rotate the camera in the di
33Cable guide Cable guideConnected cable b Accommodate the connected cables inside the cable guide of the camera mount bracket.IMPORTANT: •To pre
34Configure the network settingsConfiguring the camera so that it can be accessed from a PCThefollowingaredescriptionsforwhenthecamerawithdef
35c Selectthecamerayouwanttoconfigure,andclick[AccessCamera].Note: •Whencamerasaredisplayedin[IPSettingSoftware]screen,clickth
36Before asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after checking and tr
37•BasicPower source: 12 V DC, PoE (IEEE802.3af compliant)Power consumption:12 V DC*: 540 mA/ 6.5 WPoE 48 V: 125 mA/ 6.0 W (Class 2 devices)* ONLY C
38Scanning system: ProgressiveMinimum illumination: Color: 1.5 lx {0.15 footcandle} (F2.4, Auto slow shutter: Off (1/30 s), Gain: On(High)) 0.1 lx {0
39•LensFocal length: 0.837 mmMaximum aperture ratio: 1:2.4 (Fixed)Angular field of view:Horizontal: 182° Vertical: 176°•NetworkNetwork:SW458 10BAS
4Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5)
40Image compression method*1: JPEG (MJPEG)Image quality: 0 SUPER FINE/ 1 FINE/ 2/ 3/ 4/ 5 NORMAL/ 6/ 7/ 8/ 9 LOW (10 steps: 0-9)Transmission type: P
41Installation Guide (this document) ...1 pc.Warranty card (P model only) ...
43
Information for Users on Collection and Disposal of Old Equipment and used BatteriesThese symbols on the products, packaging, and/or accompanying docu
5Limitation of liabilityTHIS PUBLICATION IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, TH
6The network camera WV-SW458/WV-SW458M is designed to operate using a PC on a network (10BASE-T/100BASE-TX), and can be installed under eaves (shelter
7About the user manualsThere are 2 sets of operating instructions for the WV-SW458, WV-SW458M (P model), WV-SW458E, WV-SW458ME (E model) as follows.
8Note: • For further information about PC system requirements and precautions for when usingMicrosoft Windows 7, Microsoft Windows Vista
9Network securityAs you will use this unit connected to a network, your attention is called to the following security risks. q Leakage or theft of i
Comments to this Manuals