Panasonic MINAS A4P Series User Manual Page 150
- Page / 232
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
150
Normal Mode Auto-Gain Tuning
(1) Turn to the normal auto-gain tuning
mode from the monitor mode, by
pressing the SET button, then press
the mode switching button three times.
For details, refer to P.81, "Structure
of Each Mode" of Preparation.
(2) Enter the machine stiffness No. by pressing .
Display of rotational speed
of the motor (initial display)
Machine stiffness No.
Machine stiffness No. (High)
Machine stiffness No. (Low)
Tuning finishes
normally
Tuning error
Value changes toward the direction as
an arrow shows by pressing and
changes toward the reversed direction
by pressing .
(3) Shift to MONITOR/EXECUTION mode
by pressing .
(4) Operation at MONITOR/EXECUTION mode
Keep pressing until the display
changes to .
• Pin-29 of the connector, CN X5 to be
Servo-ON status.
Keep pressing for approx.3sec,
then bar increase as the right fig. shows.
The motor starts rotating.
For approx. 15 sec, the motor repeats
max. 5 cycles of CCW/CW rotation,
2 revolutions each direction per one cycle.
Tuning may finish before 5th cycles,
however, this is not an error.
(5) Write the gain value to EEPROM to prevent
them from being lost due to the power shut off.
Drive method
Ball screw direct connection
Ball screw + timing belt
Timing belt
Gear, Rack & Pinion
Others, low stiffness machine
Machine stiffness No.
8 to 14
6 to 12
4 to 10
2 to 8
0 to 8
Content
Display of error.
Value of parameter
related to gain (such as
SV/Pr10) is kept as same
as before the execution.
Cause
One of alarm, Servo-OFF or
deviation counter clear has
occurred.
Load inertia cannot be identi-
fied.
Measure
• Avoid an operation near the limit switch or home sensor switch.
• Turn to Servo-ON.
• Release the deviation counter clear
• Lower SV.Pr10 to 10 and SV.Pr11 to 50, then execute the
tuning.
• Adjust the gain manually. (Calculate the load inertia, and then
enter.)
How to Operate from the Console
<Caution>
Do not use the normal mode auto-gain tuning with the motor and driver alone. SV.Pr20 (Inertia ratio)
becomes to 0.
<Notes>
- AC Servo Motor and Driver 1
- MINAS A4P Series 1
- [Preparation] page 2
- [Setting] page 2
- [Operation Setting] page 3
- [Adjustment] page 4
- [When in Trouble] page 4
- [Supplement] page 5
- Before Using 9
- Safety Precautions 10
- [Before Using the Products] 11
- Maintenance and Inspection 12
- Introduction 14
- MSMD5AZS1S 15
- Parts Description 18
- How to Install 22
- [Preparation] 27
- • Wiring of the Main Circuit 28
- 11.0 or 32
- Tips on Wiring 34
- (by Tyco Electronics, AMP) 38
- (by Tyco Electronics , AMP) 38
- Cautions 40
- Wiring for Connector CN X5 42
- Interface Circuit 43
- Common input signals 44
- Setup with the Front Panel 48
- Built-in Holding Brake 50
- Dynamic Brake 52
- Parameter Setup 56
- Composition of Parameters 57
- List of Servo Parameter 58
- UnitTitle Function/Content 60
- Title Function/Content 65
- <Notes> 72
- Closed Control” 72
- List of Step Parameters 77
- Mode Change 81
- Monitor Mode 82
- Teaching Mode 87
- Parameter setup mode 91
- How to Use the Console 100
- SELECTION display 101
- [Setting] 103
- Outline of PANATERM 103
- How to Connect 103
- " 104
- Procedure of log on 104
- Log on of the "PANATERM 104
- [Operation Setting] 105
- Overview of Operation Setting 106
- Step Operation 107
- Homing Operation 114
- Limit Sensor 121
- Direction of homing 122
- Data Set 123
- Temporary Stop Operation 126
- Block Operation 127
- Step parameter 129
- 16-bit positioning parameter 129
- Sequential Operation 130
- Timing Chart 132
- –1 0 0 1 1 2 136
- Close the cover 137
- Absolute System 138
- What Is Full-Closed Control ? 140
- [Adjustment] 141
- Gain Adjustment 142
- Applicable Range 144
- How to Operate 144
- Adaptive Filter 147
- Normal Mode Auto-Gain Tuning 148
- Manual Gain Tuning (Basic) 152
- Gain Switching Function 155
- Instantaneous Speed Observer 160
- Damping Control 161
- [When in Trouble] 163
- When in Trouble 164
- Troubleshooting 172
- [Supplement] 175
- EC Directives 176
- EMC Directives 176
- Conformed Standards 176
- Installation Environment 176
- Surge Absorber 178
- Junction Cable for Encoder 182
- 105˚C 600V 183
- MFMCA0**2FCD 184
- MFMCA0**2FCT 184
- MFMCB0**0GET 184
- MFMCA0**3FCT 184
- 3) Table for wiring 185
- Part No. DV0P4420 188
- Fig.2 Fig.1 189
- DV0P2990 190
- Recommended components 191
- Dimensions (Driver) 192
- Mass 0.8kg 192
- Mass 1.1kg 192
- Mass 1.5kg 193
- Mass 1.7kg 193
- Mass 3.2kg 194
- Mass 6.0kg 194
- Dimensions (Motor) 195
- MSMD series 196
- MSMD 200W to 750W 197
- MSMA 1.0kW to 2.0kW 199
- MDMA 1.0kW to 1.5kW 201
- MDMA 4.0kW to 5.0kW 203
- MGMA 3.0kW to 4.5kW 205
- MFMA 2.5kW to 4.5kW 207
- MHMA 2.0kW to 5.0kW 209
- Motor with Gear Reducer 217
- Rotary encoder lead wire 218
- Position 222
- Voltage 222
- Block Diagram by Control Mode 224
- Full-closed Control Mode 225
- Input power supply 226
- Function 227
- Operation modeAuto tuning 227
- • Servo parameter (SV.Pr) 228
- FAX (03)3538-2964 231
- FAX (072)870-3151 231
- After-Sale Service (Repair) 232
Related products and manuals for Tools Panasonic MINAS A4P Series
Tools Panasonic 250280 User Manual
(8 pages)
(8 pages)
Tools Panasonic EY6813-U1 User Manual
(10 pages)
(10 pages)
Tools Panasonic SV-AV20U User Manual
(62 pages)
(62 pages)
Tools Panasonic MINAS E-series User Manual
(216 pages)
(216 pages)
Tools Panasonic EY6535 User Manual
(16 pages)
(16 pages)
Tools Panasonic EY6450 User Manual
(12 pages)
(12 pages)
Tools Panasonic EY7960 User Manual
(152 pages)
(152 pages)
Tools Panasonic EY7840 User Manual
(148 pages)
(148 pages)
Tools Panasonic EY7840 User Manual
(144 pages)
(144 pages)
Tools Panasonic EY4640 User Manual
(196 pages)
(196 pages)
Tools Panasonic EY4541 User Manual
(176 pages)
(176 pages)
Tools Panasonic EY7540 User Manual
(136 pages)
(136 pages)
Tools Panasonic EY7541 User Manual
(140 pages)
(140 pages)
Tools Panasonic EY7411 User Manual
(140 pages)
(140 pages)
Tools Panasonic EY7270 User Manual
(120 pages)
(120 pages)
Tools Panasonic CGR18650AF User Manual
(1 pages)
(1 pages)
Tools Panasonic LC-XC1238AP User Manual
(1 pages)
(1 pages)
Tools Panasonic EY6812 User Manual
(12 pages)
(12 pages)
Tools Panasonic EY6930 User Manual
(9 pages)
(9 pages)
© 2020, manymanuals.com. All rights reserved. | 0.126 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals