Panasonic MDDDT5540 User Manual Page 25
- Page / 133
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
- 25 -
List of Available Components
CN I/F Connector (For Controller)
Wiring Instructions
Place the peripheral devices such as the
controller max. 3 m away from the amplifier.
• CN I/F Connector Specifications
• The CN I/F pins assignment is shown in "Optional Parts" in Appendix.
Separate these wiring min. 30 cm from the main
circuit wires. Don't lay these wires in the same
duct of the mains or bundle with them.
T
he control power (VDC) between COM+ and COM- should
be supplied by the customer (recommended voltage:
+12VDC to +24VDC).
Do not apply power higher than 24V or 50mA to control
signal output terminal.
If you directly activate a relay using the control
signal,install a diode in parallel to the relay as
shown in the left figure. Without a diode or with
it but placed in the opposite direction, the
amplifier will be damaged.
Use a shielded twist-paired type for the wiring
of pulse input, encoder signal output, etc.
The Frame Ground (FG) is connected to
an earth terminal in the amplifier.
Preparations and Adjustments
MSDS
MOTOR
CN
SIG
CN
CN
POWER
CN
I/F
ALARM
POWER
GAIN
RS232C
COM+
GND
1
CN I/F
COM-
FG
V
DC
2
Controller
max. 3 m
min. 30 cm
Power
supply
Motor
Receptacle on the
amplifier side
10226-52A2JL
Connector to controller side
Part description
Solder type plug (Soldering type)
Connector cover
Part No.
10126-3000VE
10326-52A0-008
Manufacturer
Sumitomo
three M
- AC Servo Motor Driver 1
- Operating Manual 1
- Table of Contents 2
- Important Information 3
- Safety Precautions 4
- DANGER 5
- Check the Model of Motor 9
- Introduction 10
- Before Use 11
- Parts Description 12
- Installation 14
- General Wiring Diagram 18
- (to connect a PC or 19
- controller) 19
- (to connect an encoder) 19
- (to connect a controller) 19
- Main circuit wire diameter 20
- For 3-phase 200VAC 21
- For 1-phase 100V/200V 21
- Main Circuits 22
- Preparations and Adjustment 23
- CN SER Connector 24
- List of Available Components 25
- Velocity monitor 26
- Torque monitor 26
- CN I/F Connector 28
- Maximum rating: 34
- 30V, 50mA 34
- CN MON Connector 35
- Parameter Setting 36
- Setting the Parameters 40
- Overview of PANATERM 41
- How to Connect 41
- Starting PANATERM 43
- Procedure 43
- Trial Run 44
- Run at Position Control Mode 45
- Wiring Diagram 45
- Parameters 45
- Input Signals Status 45
- Input Signal Status 47
- 2.Check LED status 49
- 3. Set Parameters 49
- Adjustments 50
- How to Adjust Gain Manually 55
- Suppress 57
- Resonance characteristics 59
- Characteristics of 59
- Protective Functions 60
- Important information 61
- Maintenance and Inspections 66
- Replacement Guidance 67
- Troubleshooting 68
- The motor does not rotate 69
- Positioning accuracy is bad 71
- EC Directives 76
- EMC Directives 76
- Applicable Standards 76
- Peripheral Equipment 77
- Circuit diagram 78
- UL-1015 AWG16 78
- Holding brake 80
- Dynamic Brake (DB) 82
- Timing Chart 84
- - App. 14 88
- Details of Parameters 100
- Appendixes 101
- Velocity 105
- command 105
- Sequences 107
- Optional Parts 112
- Connector for Monitor 113
- Inductance 120
- Rated set-up 120
- App.47 121
- App.48 122
- App.49 123
- App. 50 124
- App. 51 125
- App. 52 126
- App. 53 127
- App. 54 128
- App. 55 129
- Specifications 130
- After-Sale Service 133
- (Repair 133
Comments to this Manuals
Related products and manuals for Tools Panasonic MDDDT5540
Tools Panasonic EY6903 User Manual
(68 pages)
(68 pages)
Tools Panasonic EY3552 User Manual
(48 pages)
(48 pages)
Tools Panasonic EYFLA2A User Manual
(48 pages)
(48 pages)
Tools Panasonic EY7410 User Manual
(14 pages)
(14 pages)
Tools Panasonic EY7460 User Manual
(44 pages)
(44 pages)
Tools Panasonic 3343109 User Manual
(6 pages)
(6 pages)
Tools Panasonic KW4S User Manual
(6 pages)
(6 pages)
Tools Panasonic EY4640 User Manual
(64 pages)
(64 pages)
Tools Panasonic MINAS A4P Series User Manual
(232 pages)
(232 pages)
Tools Panasonic 250280 User Manual
(8 pages)
(8 pages)
Tools Panasonic EY6813-U1 User Manual
(10 pages)
(10 pages)
Tools Panasonic SV-AV20U User Manual
(62 pages)
(62 pages)
Tools Panasonic MINAS E-series User Manual
(216 pages)
(216 pages)
Tools Panasonic EY6535 User Manual
(16 pages)
(16 pages)
Tools Panasonic EY6450 User Manual
(12 pages)
(12 pages)
Tools Panasonic EY7960 User Manual
(152 pages)
(152 pages)
Tools Panasonic EY7840 User Manual
(148 pages)
(148 pages)
Tools Panasonic EY7840 User Manual
(144 pages)
(144 pages)
Tools Panasonic EY4640 User Manual
(196 pages)
(196 pages)
© 2020, manymanuals.com. All rights reserved. | 0.095 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Ac sarvo motor