Panasonic PT-DS8500U Operations Instructions Page 77
- Page / 129
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
PROJECTOR SETUP menu
ENGLISH -
77
Settings
Note
Only when [DUAL] or [SINGLE] is selected in [LAMP
z
SELECT], [LAMP RELAY] is available
If [DUAL] is selected in [LAMP SELECT], only one lamp
z
is turned on for four hours after the set time.
The setting time will be the local time.
z
(
Æ
page 84)
The time can be input directly using the numeral keys on
z
the remote control.
If the lter is running low, only one lamp will light even
z
when [DUAL] is selected. The lamps will light as normal
once the lter has been replaced and the residual lter
has been reset.
LAMP POWER
The luminance of the projection lamp can be changed
depending on user’s needs or the viewing conditions.
Press ▲▼ to select [LAMP POWER].1 )
Press ◄► to switch [LAMP POWER].2 )
The setting will change as follows each time
z
◄► is pressed.
HIGH LOW
HIGH
Set when high brightness is
necessary.
LOW
Set when high brightness is not
necessary.
Note
When set to [LOW], it is possible to reduce power
z
consumption, reduce operating noise and extend lamp
service life.
BRIGHTNESS CONTROL
This projector has a built-in brightness sensor
for measuring the lamp power and a function for
correcting the screen brightness according to the
change in lamp power.
With this function, you can reduce changes in
brightness caused by aging of the lamps when
multiple screens are projected using multiple
projectors, or minimize any uctuations in brightness.
J
BRIGHTNESS CONTROL GAIN
This function is used to adjust the brightness
when multiple screens are projected using multiple
projectors.
Press ▲▼ to select [BRIGHTNESS 1 )
CONTROL GAIN].
Press ◄► to adjust.2 )
Operation
Adjustment
Adjustment
range
Brightness
Max. quantity
of brightness
control
Press ►. Increases Decreases
Maximum
value 100 %
Press ◄. Decreases Increases
Minimum
value 20 %
Note
When using one projector, the maximum quantity of
z
brightness control is obtained by subtracting the value
of [BRIGHTNESS CONTROL GAIN] from 100 %. If the
[BRIGHTNESS CONTROL GAIN] is set to 100 %, the
maximum quantity of control is 0 % and the brightness
cannot be corrected using the brightness control function.
The brightness will not stabilize for 8 minutes after the
z
lamp is turned on. Make adjustments after at least eight
minutes has elapsed after the power is turned on.
The adjustment in [BRIGHTNESS CONTROL GAIN]
z
will be reected in all of the image signals, internal test
pattern, and on-screen menu.
[BRIGHTNESS CONTROL GAIN] remains effective even
z
if [BRIGHTNESS CONTROL SETUP] is [OFF].
J
BRIGHTNESS CONTROL SETUP
This function is used to set the operation of the
brightness control.
Press ▲▼ to select [BRIGHTNESS 1 )
CONTROL SETUP].
Press <ENTER> button.2 )
The [BRIGHTNESS CONTROL SETUP] screen
z
will be displayed.
Press ▲▼ to select [MODE].3 )
Press ◄► to switch [MODE].4 )
The setting will change as follows each time
z
◄► is pressed.
OFF AUTO PC
OFF
Brightness correction with the
brightness sensor is not performed.
AUTO
Brightness is corrected with the
brightness sensor. If lamp power
changes, screen brightness will correct
automatically.
PC
Nine or more projectors are operated
simultaneously using a computer and
the [Multi Projector Monitoring & Control
Software].
- Operating Instructions 1
- PT-DZ8700U 1
- PT-DS8500U 1
- PT-DW8300U 1
- Important Safety Notice 2
- Heightened luminance 4
- Lengthened lamp 4
- Reduced standby power 4
- Contents 5
- Maintenance 7
- Appendix 7
- - ENGLISH 10
- Cautions when transporting 11
- Cautions when installing 12
- ENGLISH 13
- Security 14
- Cautions on use 14
- Cleaning and maintenance 15
- Disposal 15
- Accessories 16
- About Your Projector 17
- Projector body 18
- Setting projector ID number 20
- Using a wired remote control 20
- Setting up 21
- Connections 34
- How to remove the projection 37
- Powering ON/OFF 38
- Powering up the projector 39
- Making adjustment and 39
- Powering off the projector 40
- Direct power off function 40
- Projecting 41
- Using the SHUTTER function 46
- On-screen display function 46
- Switching the input signal 46
- STATUS function 46
- Automatic adjustment 47
- Using the FUNCTION button 47
- Displaying the internal 47
- Changing the picture aspect 48
- Menu Navigation 49
- MAIN MENU 50
- SUB MENU 50
- PICTURE menu 52
- CONTRAST 53
- BRIGHTNESS 53
- COLOR TEMPERATURE 54
- SYSTEM DAYLIGHT VIEW 55
- SHARPNESS 56
- NOISE REDUCTION 56
- DYNAMIC IRIS 56
- (PT-DZ8700U/PT-DS8500U only) 57
- POSITION menu 58
- (PT-DZ8700/PT-DS8500 only) 60
- (PT-DW8300 only) 62
- ADVANCED MENU 63
- INPUT RESOLUTION 64
- CLAMP POSITION 64
- EDGE BLENDING 64
- FRAME DELAY 66
- RASTER POSITION 66
- DISPLAY LANGUAGE menu 67
- DISPLAY OPTION menu 68
- (PT-DZ8700 only) 70
- AUTO SIGNAL 71
- AUTO SETUP 71
- (Only RGB input) 72
- BACK COLOR 74
- STARTUP LOGO 74
- PROJECTOR SETUP menu 75
- COOLING CONDITION 76
- LAMP SELECT 76
- LAMP RELAY 76
- LAMP POWER 77
- BRIGHTNESS CONTROL 77
- STANDBY MODE 81
- SCHEDULE 81
- NO SIGNAL SHUT-OFF 84
- REMOTE2 MODE 84
- FUNCTION BUTTON 84
- DATE AND TIME 84
- LENS CALIBRATION 85
- FILTER COUNTER RESET 85
- LOAD ALL USER DATA 86
- INITIALIZE 86
- SERVICE PASSWORD 86
- SAVE ALL USER DATA 86
- P IN P menu 87
- TEST PATTERN menu 88
- SIGNAL LIST menu 89
- Managing the sub memory 90
- SECURITY menu 91
- DISPLAY SETTING 92
- TEXT CHANGE 92
- MENU LOCK 92
- MENU LOCK PASSWORD 92
- CONTROL DEVICE SETUP 93
- Network connections 95
- NETWORK menu 100
- Monitor Lamp indicators 107
- Replacement 109
- Troubleshooting 112
- Technical Information 114
- Control commands via LAN 115
- Serial terminal 117
- REMOTE 2 IN terminal 120
- List of compatible signals 122
- Specications 124
- Dimensions 126
- About brand 126
- Attachment procedure 127
- ヱㄏㄔㄐㄏㄊチヤㄐㄓㄑㄐㄓㄕㄊㄐㄏ 129
Related products and manuals for Data projectors Panasonic PT-DS8500U
(74 pages)
(62 pages)© 2020, manymanuals.com. All rights reserved. | 0.775 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals