Panasonic PT-DS8500U Operations Instructions Page 81
- Page / 129
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
PROJECTOR SETUP menu
ENGLISH -
81
Settings
Display the internal test pattern [ALL 9 )
WHITE] on all projectors.
Set [BRIGHTNESS CONTROL GAIN] 10)
of all projectors to 100 %.
Set [BRIGHTNESS CONTROL GAIN] 11)
of the darkest projector to 90 %.
Adjust [BRIGHTNESS CONTROL 12)
GAIN] of the other projectors to that
of the projector that was set to 90 %.
Set [MODE] of [BRIGHTNESS 13)
CONTROL SETUP] of all projectors to
[AUTO] and set [LINK] to [GROUP A].
[APPLY] [BRIGHTNESS CONTROL 14)
SETUP] of all projectors and press
<ENTER> button.
Brightness control will commence.
z
Note
The brightness is corrected automatically each time the
z
lamps are turned on using the power switch etc.
If the brightness uctuates signicantly or the lamp has
z
been replaced, re-adjust the brightness control.
STANDBY MODE
You can select the electrical consumption while in
standby mode.
Press ▲▼ to select [STANDBY MODE].1 )
Press ◄► to switch [STANDBY 2 )
MODE].
The setting will change as follows each time
z
◄► is pressed.
NORMAL ECO
Note
With [ECO] setting, NETWORK function, RS-232C output
z
and some of RS-232C commands are not available.
When switch on the projector, projection will start about
10 seconds late.
SCHEDULE
This sets the command execution schedule for each
day of the week.
J
How to enable the SCHEDULE
function
Press ▲▼ to select [SCHEDULE].1 )
Press ◄► to switch [SCHEDULE].2 )
The setting will change as follows each time
z
◄► is pressed.
ON OFF
Note
If [SCHEDULE] is set to [ON], the setting for [STANDBY
z
MODE] is automatically set to [NORMAL] and cannot be
changed. Even if [SCHEDULE] is then set to [OFF] when
in this state, the setting of [STANDBY MODE] remains at
[NORMAL].
J
How to assign a program
With [SCHEDULE] switched to [ON], 1 )
press <ENTER> button.
The [SCHEDULE] screen will be displayed.
z
Select and assign program to each day 2 )
of week.
Press ▲▼ to select a day of week and press
z
◄► to select a program number.
You can set the program from No.1 to No.7.
z
“- - -” indicates that the program number has
not been set yet.
J
How to set a program
You can set up to 16 commands to each program.
On the [SCHEDULE] screen, press ▲▼ 1 )
to select [PROGRAM EDIT].
Press ◄► to select a program number 2 )
to be set and press <ENTER> button.
Press ▲▼ to select a command 3 )
number and press <ENTER> button.
You can change the page using ◄►.
z
- Operating Instructions 1
- PT-DZ8700U 1
- PT-DS8500U 1
- PT-DW8300U 1
- Important Safety Notice 2
- Heightened luminance 4
- Lengthened lamp 4
- Reduced standby power 4
- Contents 5
- Maintenance 7
- Appendix 7
- - ENGLISH 10
- Cautions when transporting 11
- Cautions when installing 12
- ENGLISH 13
- Security 14
- Cautions on use 14
- Cleaning and maintenance 15
- Disposal 15
- Accessories 16
- About Your Projector 17
- Projector body 18
- Setting projector ID number 20
- Using a wired remote control 20
- Setting up 21
- Connections 34
- How to remove the projection 37
- Powering ON/OFF 38
- Powering up the projector 39
- Making adjustment and 39
- Powering off the projector 40
- Direct power off function 40
- Projecting 41
- Using the SHUTTER function 46
- On-screen display function 46
- Switching the input signal 46
- STATUS function 46
- Automatic adjustment 47
- Using the FUNCTION button 47
- Displaying the internal 47
- Changing the picture aspect 48
- Menu Navigation 49
- MAIN MENU 50
- SUB MENU 50
- PICTURE menu 52
- CONTRAST 53
- BRIGHTNESS 53
- COLOR TEMPERATURE 54
- SYSTEM DAYLIGHT VIEW 55
- SHARPNESS 56
- NOISE REDUCTION 56
- DYNAMIC IRIS 56
- (PT-DZ8700U/PT-DS8500U only) 57
- POSITION menu 58
- (PT-DZ8700/PT-DS8500 only) 60
- (PT-DW8300 only) 62
- ADVANCED MENU 63
- INPUT RESOLUTION 64
- CLAMP POSITION 64
- EDGE BLENDING 64
- FRAME DELAY 66
- RASTER POSITION 66
- DISPLAY LANGUAGE menu 67
- DISPLAY OPTION menu 68
- (PT-DZ8700 only) 70
- AUTO SIGNAL 71
- AUTO SETUP 71
- (Only RGB input) 72
- BACK COLOR 74
- STARTUP LOGO 74
- PROJECTOR SETUP menu 75
- COOLING CONDITION 76
- LAMP SELECT 76
- LAMP RELAY 76
- LAMP POWER 77
- BRIGHTNESS CONTROL 77
- STANDBY MODE 81
- SCHEDULE 81
- NO SIGNAL SHUT-OFF 84
- REMOTE2 MODE 84
- FUNCTION BUTTON 84
- DATE AND TIME 84
- LENS CALIBRATION 85
- FILTER COUNTER RESET 85
- LOAD ALL USER DATA 86
- INITIALIZE 86
- SERVICE PASSWORD 86
- SAVE ALL USER DATA 86
- P IN P menu 87
- TEST PATTERN menu 88
- SIGNAL LIST menu 89
- Managing the sub memory 90
- SECURITY menu 91
- DISPLAY SETTING 92
- TEXT CHANGE 92
- MENU LOCK 92
- MENU LOCK PASSWORD 92
- CONTROL DEVICE SETUP 93
- Network connections 95
- NETWORK menu 100
- Monitor Lamp indicators 107
- Replacement 109
- Troubleshooting 112
- Technical Information 114
- Control commands via LAN 115
- Serial terminal 117
- REMOTE 2 IN terminal 120
- List of compatible signals 122
- Specications 124
- Dimensions 126
- About brand 126
- Attachment procedure 127
- ヱㄏㄔㄐㄏㄊチヤㄐㄓㄑㄐㄓㄕㄊㄐㄏ 129
Related products and manuals for Data projectors Panasonic PT-DS8500U
(74 pages)
(62 pages)© 2020, manymanuals.com. All rights reserved. | 0.088 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals